... light after arming.

"walk me home..." mode

It is implemented as follows: after turning off the ignition, "blink" the high beam, and then after arming the car, the car guides you with the headlights for 30 seconds. For each "blink" lighting time increases by 30 seconds. Can be set up to 2 minutes.

Automatic door lock when driving. Turn on the ignition, press the central locking button and hold it for a few seconds until it clicks. Now, every time you get into the car and start moving, the central lock will automatically close the car when you reach a speed of 15-20 km/h.

Function of a selective mode of unlocking of doors. Simultaneously press and hold (about 5 seconds) the door lock and unlock buttons on the ignition key. Similar actions lead to the disabling of this mode. Now, when you press the door unlock button once, only the driver's door and the fuel tank hatch will open. Pressing again will unlock all doors.

Function of a selective mode of unlocking of doors with "Intelligent Key". Simultaneously press and hold (about 10 seconds) the door lock and unlock buttons on the ignition key. Within 3 seconds, press the lock switch button on the driver's door. Similar actions lead to the disabling of this mode. The functionality is the same.

Hello dear car enthusiasts!

This is another review from a series of "autopuffs".
The thing is purely specific, so there will be a lot of pictures.

The previous car had this option, so there were no problems.
I didn't think of that when I bought a new car :(
In the Land of the Rising Sun, most likely, democracy is so strong that you can throw a typewriter on the street with open windows and no one will democratize anything. There was no such function in the machine :(.
So we will eliminate this shortcoming :)
In the service, where they put the signaling, the uncles tearfully asked, "Well, put such a little thing," but the uncles were adamant, constantly remembering the mother of Japanese designers. The uncles also scared me with a terrible CANBUS beast that hides in a typewriter and bites the hands of naughty Russian auto electricians.

Time has passed...

The constant return to the machine to close the windows got me, so I took out an old nubuck from under the sofa and began to look for information on taming the evil CANBUS-a-barabas, well, some cheap glass closer. I drove through the service station and found out that the price for such an item is from 600 rubles and more, but with the above beast it is even more expensive.
I thought, thought, thought... and found it on a alisha for ~$29. There were no reviews. At autoforums, people are not aware, everyone sculpts what they have.
Thought, thought, thought … ordered.
After 29 days (for me personally, a record from the PR), this thing came.

Unpacking process and contents

What struck me the most was the inscription on the box “Original car parts” and on the module itself “QASHQA T". Nu-nu…

Well, actually the contents of the box: module, cable, clips, adhesive tape, manual.

After waiting for warm days, it was decided to put this thing.
Looking ahead, I will say that real installation takes 1-2 hours, or even less.
There was a problem with the definition of wires, searching the Internet and autoforums, but the brain turned out to be stronger.

So, installation. A lot of photos. Maybe not everything will be visible, but I myself dance, I sing myself, I sell tickets myself, I took pictures at the time of installation and it was not always possible :).

Well, off we go...

In the presence of the driver's door - 1 piece, by the way, on the right on the rug, which greatly facilitated the process of removing the lining for me.


Remove the decorative door trim. We start to pry from the bottom and go up.




We unscrew the screws on the handle (2 pieces - a curly screwdriver). DO NOT REMOVE the handle otherwise it can be broken.


We pry the casing from below, find the places for installing the clips and pull the casing towards ourselves.



As soon as all the clips are snapped off from below, we begin to snap them off on the sides, feeding the skin towards ourselves. After that, we release the door handle (pull a little towards ourselves) and slightly lifting it up, disconnect the trim from the door.


Wires go to the power window control unit, to remove them, turn the casing to the side clockwise and get access to the connectors. There is usually a latch on the connector, press on it and remove the connector. There are 2 of them.


Congratulations, the door trim has been removed. :) We put aside.


We stupidly look at the connection diagram and count the number of holes on the connectors. converges.


We connect. It is impossible to make a mistake in the direction of connection, there are grooves with keys and each plug has its own connector.


We unscrew the door speaker (3 bolts - a key for 10). And unplug it.


Inside we see a wiring harness that bifurcates. We need a thin part of the harness, there are usually from 2 to 4 wires, this was found out on auto forums. I had 3 of them.


Since there are 2 wires with the inscriptions “LOCK” and “UNLOCK” on the module cable, we will look for them.


From under the above sofa we take out an old device and look for ...
By the way, the arrows show the places where you can disconnect the clamps and access to the body of the tourniquet will become easier :)

Understood LOCK-blue, UNLOCK-orange.


We take out the rubber plug from the top of the door and put the wires in there.

Well, are you tired? :) Most of it is already done, drink coffee for 10 minutes and get to work.

The kit included two connectors.


Let's connect them soon...


As you can see, a separate wire is in the lower part, and the wire of the bundle is on top and at the same time we put a knife on both wires, press on it and close the lid. Here's what happened.


We do the same with the second one. We receive.


We put the wires in place, the plug, electrical tape, foam rubber, do not forget to put the little things back into place with the latches.

We put the speaker in place, fasten the closer module.


The place is not chosen very well, but it is optimal :)


We put the casing in place by the impact method, tighten the screws on the handle, put the trim in place (starting from the top). It should work, what was ...

We happily clap our hands. The module is installed, the review is finished.

Pros.
+ Now, when arming, all windows are closed.
+ On the driver's door, now all buttons have the function of opening / closing with one touch (previously only the driver's glass).
+ Installation costs are minimal.
Minuses.
- There aren't any yet.

Well, lastly.

SUNROOF (for some

Closing

opening

ATTENTION

It is forbidden to put heavy objects on the ceiling

sunroof or on the roof of the car next to it.

It is forbidden to hang any objects in the sun -

skylight protective cover. This may bring
cause the curtain to be deformed or damaged.

Leaving the car for a long time under

direct sunlight, cover the sunscreen
curtain to prevent strong heating of the air
spirit in the car.

Depending on the environment or conditions
movement, the automatic reverse function can
free to turn on upon impact or load,
similar to eating.

Re-initialization procedure after
battery connections

Some Power Window Functions
(automatic closing, auto-reverse) do not work
properly after disconnecting the wire from the battery
battery and interruption of the power supply. For
re-initialization of the electric glass functions
lifts, perform the following procedure.

Turn the ignition switch to the ON position.

If the driver's door glass is closed, fully

turn it off using the switch on the driver's door.

To close the driver's door glass, pull up

and hold the switch on the driver's door. Hold-
turn the switch on for about 5 seconds after
until the window is completely closed and release it.

Check if the glass functions are working properly.

lifts.

If you continuously open and close the glass with
using the power window, this may lead to
disruption of its normal operation. Do the following
actions.

If the normal operation of the power window functions is
collapsed and after performing the above procedure,
repeat it. If necessary, contact the service
station of an authorized NISSAN dealer to check the system
we are power windows.

Automatic mode allows you to fully raise or
lower the window without holding the switch.

To fully lower the window, press
power window switch to the second click and release
those of him. To fully raise the glass, pull
power window switch up to the second click and
let him go. In this case, it is not necessary to hold the switch
body during power window operation.

In order to stop the operation of the power window in the car
automatic mode, press the switch or pull
it in the opposite direction.

DANGER

There is a small gap directly

before the fully closed position of the glass, with
which the presence foreign objects can not be
discovered. When closing windows, make sure that
the openings do not contain fingers or hands of passengers,
in the car, or any objects.

window glass (if you hold the switch in the
closing action).

The automatic reverse function allows automatic
ski to lower the glass if any object is in
window opening when it is closed automatically.
If during the movement of the glass up the control system
detects an obstacle in the window opening, the glass immediately
slowly stop closing and start moving downwards.

Dashboard and controls

middle position

When the switch is set to the middle position, the inside
morning lighting turns on when you open the car door
car.

INTERIOR LIGHTING TIMER
car)

Interior lighting stays on for a while
following cases:

When the ignition is turned off.

When unlocking car doors.

When opening and then closing any

car doors.

The timer is interrupted and the interior lighting is turned off.
etsya in the following cases:

When locking car doors.

The ignition switch is turned to the ON position.

INDIVIDUAL LIGHTING PLATES
(for some versions
car)

INDOOR LIGHTING
DEVICES

ATTENTION

Do not turn on the interior lights for a long
living time with the engine off. It may
lead to battery discharge.

NOTE

The ceiling lamps of the interior lighting will turn off after some
second time, unless the ignition switch is
is set to ACC or ON.

LIGHT SWITCH
PASSENGER CABIN

The interior lighting switch has three positions:
ON

and mean

ON position

If the switch is in the ON position

Then turn on

Chat plafonds interior lighting.

OFF position

If the interior light switch is in the
position OFF

Interior lighting fixtures will not

burn, regardless of other conditions.

SHUTTER CONTROL

The sunblind only works when the
ignition.

DANGER

Do not hold hands, fingers or any other parts
body in the area of ​​the rear sunshade. You
you may get injured.

Opening and closing

Manual control

To close the sunshade, press
and hold the CLOSE side of the switch

For

so that the blind does not close completely, release the switch
chatel.

To open the sunshade, press
and hold the OPEN side of the switch

For

so that the blind does not open fully, release the switch
chatel.

Automatic control

To fully open or close the sun
curtain, briefly press the corresponding side
switch and release it. To stop
sunblind when opening or closing
ion, press either side of the switch.

If the control unit detects an obstacle in the way
curtains, the curtain will automatically open fully.

Dashboard and controls

This lamp can be turned on or off by pressing
switch

CARGO LIGHT
OFFICES

Luggage compartment light automatically
turns on when the tailgate is opened.
After closing the tailgate, the ceiling light will
turns on.

MAKE-UP MIRROR LIGHT
(for some versions
car)

Vanity mirror light on sunscreen
The bubble turns on when you open the cover of this mirror.

To turn on the lampshade for reading cards, use the corresponding
switch switch.

: ON position

: OFF position

REAR INTERIOR LIGHT/
REAR LIGHT FOR READING
(for some versions
car)

Interior lighting dome

(for some vehicle variants)

Reading lamps (for some vehicle versions)

Preparing to start moving

Key with integrated remote control

Key Intelligent Key with spare/mechanical key

1. Intelligent Key

2. Spare/mechanical key (Built in Intelligent key

Key), see Spare/mechanical key for ex-
friction situations (vehicles with Intelligent
Key)" later in this chapter.

NISSAN ANTI-THEFT KEY
(NATS)*

You can use your car only with the help of
we make keys specially made for your car
mobile. Your vehicle can only be used
keys compatible with the NISSAN Anti-Theft security system
System (NATS)* (See the Security System section later in this
chapter).

INTELLIGENT KEY (for some
vehicle options)

Your vehicle can only be driven if you have
Intelligent Keys that are registered in the system
Intelligent Key and security system NATS*. For one car
You can register up to 4 Intelligent Keys on your mobile.
New keys must be registered with an official
NISSAN dealer before they are first used
us together with the Intelligent Key system and NATS system of your
car. Because the registration process requires
clear memory in all Intelligent system components
Key, then you need to submit all the keys you have
NATS official NISSAN dealer.

*: Immobilizer

ATTENTION

Be sure to carry the Intelligent Key with you. By-

when leaving the car, do not leave the Intelligent Key
inside the car.

Be sure to carry the Intelligent Key with you when

driving a car. Intelligent Key System Key
is a high-tech device
with built-in radio transmitter. In order to avoid
key damage, please note the following.

The Intelligent Key is tamper-resistant

moisture, but excessive moisture may damage
feed him. If moisture gets on the Intelligent Key,
wipe it dry immediately.

Do not allow the Intelligent Key to come into contact with pre-

sleeping or salt water, as it can
disable the key.

Do not apply bending force to the key

drop it and do not knock the key on other pre-
metam.

Do not store the Intelligent Key for

for a long time at a temperature pre-
above 60°C.

It is forbidden to change the design of the key

intelligent key.

It is forbidden to use magnetic keychains for

keys.

Do not store the Intelligent Key near

equipment that is a source of strong
magnetic radiation such as television
receivers, audio equipment and personal
computers.

If the Intelligent Key is lost or stolen, the company

NISSAN Recommends Removing Identification Code
this key from the vehicle's memory unit. This pre-
prevents unauthorized access
into the car using your lost key
intelligent key. To erase the identification code
contact an authorized NISSAN dealer.

1.2.8. Opening and closing windows

The switches in the driver's door can control all power windows. In other doors there are power window control keys for each specific door.

Press the key to open the corresponding window.

Always close windows when parking or leave it unattended.

After turning off the ignition, you can still use the power windows for about 10 minutes, if during this time the key has not been removed from the ignition lock or none of the front doors has been opened.

Buttons in the driver's door:

1. Key for left front window.

2. Key for right front window.

Keys for rear windows:

3. Safety switch to disable the window controls in the rear doors.

4. Key for the left rear window.

5. Key for right rear window.

Safety switch

The safety switch 3 in the driver's door can be used to de-energize the power window controls in the rear doors.

The safety switch is unlocked: the buttons in the rear doors are operational.

The safety switch is fixed: the buttons in the rear doors are inoperative.

Automatic lifting and lowering windows

To automatically raise the windows, briefly pull up the button of the corresponding window to the second fixed position. The window will close completely.

To automatically lower the windows, briefly press down the button of the corresponding window to the second fixed position. The window will fully open.

Close all windows to restore automatic operation.

Insert the key into the driver's door lock and hold it for at least one second in the locked position. Automatically raise and lower windows again workable.

Keys 1 and 3 each have two fixed positions for opening and closing windows. This simplifies the process of opening and closing windows.

If the key is pressed or extended to the first position, the window opens and closes as long as the key is pressed or extended. If you briefly press or pull the key to the second position, the window opens or closes with automatic control opening (automatic lowering) or closing (automatic lifting). If you act on the key while the window is opening or closing, the glass stops.

After switching off the ignition, the automatic control of closing and opening the windows is no longer active, even if the key has not yet been removed from the ignition.

If the battery has been disconnected and reconnected or has been discharged, automatic control is not effective and must be restored.

In the event of a power window malfunction, automatic control and overload protection are not fully operational.

Overload protection

Power windows are equipped with overload protection. This reduces the chance of injury when closing windows.

If the closing of the automatic window is prevented or the glass is difficult to move, the window stops and then lowers.

Before trying to close the window again, take ten seconds to see why the window won't close. After ten seconds, the closing force of the window will automatically increase.