What means to wash the floors after repair. How to clean and quickly clean the floor. We use laundry soap

First you need to determine which floor you are going to clean - parquet, linoleum, laminate or carpet, because each type of floor has its own methods and means of cleaning. Let's consider each type.

Ways to clean different types of floors

• Parquet or wooden unpainted floor can be washed no more than 2 times a year. Before that, it must be swept with a soft brush or broom. Then wash with soap hot water and wipe dry with a hard natural cloth, preferably burlap. Scrub especially dirty places with a brush with fine sand, but in no case with abrasive detergents. If the floor is varnished, then after sweeping it can be washed with warm water without detergents, especially dirty places can be scrubbed with a brush and soap and immediately wiped dry. After washing, dry lacquered floors should be rubbed with a soft cloth and polish to a shine. By the way, during cleaning, a bucket of water should only stand on a tiled floor, because wooden floors really do not like prolonged contact with moisture. And after cleaning, you have a chance to find a swollen circle from the bottom on the floor under the bucket.
• Linoleum it is best to wash with water and liquid detergent such as Fayeri, Mr. Proper and others. Never wash linoleum with soda, alcohol or any acids, it does not tolerate them. You will just ruin the floor. Stains from iodine, brilliant green, coffee or a felt-tip pen can be wiped off with kerosene, gasoline or turpentine, but immediately after that, wash with water and wipe dry. Shine to linoleum will give a cold decoction of potatoes without salt - just wipe the floor with it.
• Laminate is a multi-layered floor. And so that it does not exfoliate, you must immediately remember that the laminate does not like moisture. Therefore, the floor must first be swept or vacuumed, and then wiped with a damp cloth. You can wipe the floor with vinegar water at the rate of 1 tablespoon per 5 liters of water. When heavy pollution and greasy stains, use detergents with a neutral PH. A felt-tip pen, nail polish, lipstick are rubbed with a household solvent, acetone or methyl alcohol, then the place is wiped with a damp cloth.
• Carpet covering, or carpet, needs systematic cleaning with a vacuum cleaner. For dry cleaning of heavily soiled carpet, a special absorbent is used, which can be bought at the store. Cleaning should be strictly according to the instructions. Most often, the absorbent should be evenly scattered over the carpet, let it stand for a while, and then remove it with a vacuum cleaner. Foam cleaning is carried out with special dry foam in aerosols. It must be sprayed onto the carpet, evenly distributed with a brush, allowed to dry and vacuumed. Wet cleaning is carried out using special shampoos and a washing vacuum cleaner. Stains from tea, coffee, juice, wine, blood are removed with a solution of alcohol or vinegar essence. Stains from mayonnaise, ketchup, toothpaste, ice cream, chocolate and dog (cat) poop are first treated with detergent, then with ammonia. Stains from a felt-tip pen, ballpoint pen, nail polish, mascara and grease are removed using special stain removers.

But, nevertheless, the key to cleanliness of any floor is its regular cleaning!

No matter how carefully you try to carry out work during the repair, it will not be possible to avoid floor contamination. Traces of plaster, whitewashing, painting, construction debris and dust - all this leaves persistent marks on the floor and needs further cleaning. Remember, it will be necessary to wash off any pollution after repair in several stages. The first wash is carried out with clean warm water and collects the main debris. Subsequent washes should be carried out depending on the work being carried out and the contamination present. We will tell you how and how to quickly and easily clean the floor after repair.

The most difficult thing is to wash whitewash from the floor covering. To clean the floor without streaks, frequent changes of water, thorough rinsing of the cloth and the use of suitable improvised means are required.

Salt and vinegar. Replace the water after the initial wash with clean water. Add to the bucket 5 tbsp. l. salt and wash off traces of whitewash. Finish cleaning by washing the floor with a weak solution of vinegar (2-3 tablespoons per 5 liters of water).

Sunflower oil and vinegar. Add a little sunflower oil to warm water (1 tsp per 1 liter of water). Wash the stains with the prepared solution. Drain the water, prepare a weak vinegar solution and re-mop the floor.

Potassium permanganate. Prepare a bright pink potassium permanganate solution.

Wash the floors first with them, and then clean water.

Kerosene. If you need to wash old traces of whitewash, prepare a product from 5 liters of water and 150 g of kerosene. On stubborn stains, apply a few drops of undiluted kerosene and rub with a rag or sponge. For removing bad smell use vinegar solution. Wash the floor with it several times.

Domestos Pine Fresh. This all-purpose cleaner also effectively removes old whitewash. Prepare a solution of 50 ml of product and 5 liters of water and wash the floor with it.

How to clean the floor after painting

To wash a painted floor, prepare a solution of 1 tbsp. l. ammonia and 1 liter of water. Wash off the dirt with the prepared product. If wooden surface you need to restore the shine, walk on it with a cloth dipped in linseed oil.

Rubbing alcohol will help you remove paint stains from a painted surface. Soak a cotton pad in it and apply it on the stain. Leave for a few minutes. Then take a spatula and carefully scrape off the dirt.

Washing parquet

When washing parquet, it is important to remember that the board is afraid of moisture. Therefore, dirt can be removed with a damp, well-wrung cloth. First, collect debris from the floor surface with a vacuum cleaner with a special parquet nozzle. Then prepare a solution of 100 ml of Parquet wash & shine and 10 liters of warm water and rinse the parquet with it. The preparation covers the floor with a water-repellent film and restores the shine to the surface.

If during the repair paint stains got on the parquet, then you can remove it with the usual baby cream, cologne or alcohol. Apply one of the products to a cotton pad and place it on the stain for 1-2 minutes. After the paint has soaked, carefully remove it from the surface of the parquet. Wipe the floor with a damp cloth and wax.

Do not use coarse brushes, metal scrapers, abrasives or strong solvents to clean the parquet. When choosing a product, give preference to substances with a mild composition, such as white alcohol, kerosene, methyl alcohol.

Laminate washing

Despite the fact that laminate flooring is characterized by heat resistance, impact resistance and resistance to stress, it requires careful handling and competent care. To wash the laminated surface, you can use both the special Laminate wash & shine and folk methods. Remember that laminate does not tolerate well high humidity, so it is not recommended to wet it heavily. To wipe off stubborn dirt, use a soft cloth that will not damage the top protective layer.

If you prefer folk methods, then you can use a solution of vinegar (1 tablespoon per 1 liter of water). However, the use of a special tool will allow not only to wash different types pollution, but also gives the surface a radiant look and refreshes the smell in the room.

Sometimes black footprints can remain on the laminate flooring, which are not washed off with water. In this case, use a regular eraser. Dimexide will help remove the mounting foam. You can buy it at a pharmacy. Apply a little on the stain and leave for a while. Then carefully remove the dirt with a spatula and a sponge.

Linoleum washing

All of the above methods are suitable for washing linoleum. However, ammonia, gasoline and alcohol should be used with caution. Before using them, it is better to test in an inconspicuous place.

Since the surface covered with linoleum is not afraid of moisture, it can be washed with a washing vacuum cleaner. This method of cleaning will allow you to easily and quickly cope with stains and whitish spots. If, after washing, the linoleum has darkened and changed its original appearance, treat it with a rag soaked in drying oil, and then rub it with an old woolen sock.

Since the surface covered with linoleum is not afraid of moisture, it can be washed with a washing vacuum cleaner

To manually wash a floor covered with linoleum, you will have to prepare 2-3 clean rags. Only a frequent change of water and rags will allow you to wash such a floor without streaks. If there are particularly stubborn stains on the surface, use turpentine. It perfectly copes with the majority of pollution remaining after repair. To return the linoleum to its original shine, rub it with special mastic or linseed oil.

Here are a few more tips that will greatly facilitate the process of cleaning the floor:

• Do not use baking soda to clean linoleum. It negatively affects the color and structure of the surface.
• Do not let any paint on the floor dry out. Remove it while it's fresh.
• Do not use potassium permanganate solution on varnished surfaces. Otherwise there will be divorces.
• To remove enamel or oil paint from the tiled floor, use the KROT pipe cleaner. It effectively removes dirt and restores shine to the tiles.

By applying the listed cleaning tips and methods, you will be able to handle the final stage of the repair quickly and with minimal effort. But in order not to have to puzzle over how to wash this or that stain, take action before starting the repair: cover the floor with oilcloth or polyethylene and attach their ends with masking tape. So you can reduce the time spent cleaning the floor several times.

How to remove construction dust after repair

After repairs carried out in the apartment, often remains on the floor a large number of construction debris and dust. It can be limescale, cement residues, sand and other contaminants that are quite difficult to remove from the surface. In order for cleaning to be effective, proven effective methods are needed.

In order to make it easier to clean up dirt later, cover the entire area of ​​​​the room with large-sized polyethylene or newspapers before starting repairs. This will make it possible to protect the floor from a large amount of dirt and it is easier to wash it afterwards.

Wear gloves if you are using special detergents, as cleaning solutions contain a lot of chemicals that are harsh on the skin.

Carefully scrape off pieces of cement, alabaster and other materials that have dried to the floor with a spatula, then moisten the stains remaining from them with a damp cloth.

Cleaning of dirt from laminate and parquet should be carried out using only special products intended for these coatings.

Cleaning of the premises should be carried out in the following order:

• collect large pieces of construction debris;
• with a broom dipped in water, sweep away the main dirt, starting from the corners;
• wash the floor with a wet cloth using plenty of water;
• change the water and rinse well again with detergent;
• repeat the procedure several times, changing the water frequently.

Washing off pollution

In order to wash gypsum or lime dust and various building contaminants left after repairs, there are several effective ways.

• Construction dust is well removed with a solution of vegetable oil.

  Pour a few tablespoons of oil into warm water and stir. Wash the room, then empty the bucket. Then wash everything with a solution with a little vinegar. At the end of cleaning, thoroughly rinse the entire area with clean water.

• To wash the room after repair, use ordinary salt. First, wash the entire area with water with the addition of any detergent. Change the water and add about half a cup of salt to the bucket. After washing with salt, wipe the floor with clean water.
• Potassium permanganate (potassium permanganate) will help to remove construction dust after repair. Dilute some powder in water for a vibrant pink color.

  We clean the floor after repair

  Rinse the area thoroughly.

• In order to remove building dust, you can use kerosene. Pour about one hundred grams of kerosene into a bucket of water. Wash the entire floor area. Rinse again if necessary.
• You can wash the floor from construction dust using universal surface cleaners (Domestos, Amway). Dilute the product in warm water according to the instructions. Wash the entire contaminated area. Then wipe with clean water.
• To remove various dirt after repair, you can use special washing floor cleaners (Mr. Muscle or Mr. Proper). Dilute them as indicated in the instructions and thoroughly wash dirty surfaces. Repeat if necessary.
• In order to remove gypsum and lime dust, there is a special Probel cleaner, which can be bought at hardware and building stores. Dilute it with warm water according to the instructions. Rinse the contaminated coating well, then rinse with clean water.

Cleaning of wooden surfaces

Hardwood floors require special care. Very beautiful laminate and parquet coatings require careful personal care. If a large amount of moisture enters, they can be subjected to deformation. To wash such surfaces, use the following methods:

• If you have natural wood floors at home, with painted wooden planks dirt can be removed with a solution of ammonia. Dilute it in water at the rate of 1 tablespoon per liter of water. Rinse wood thoroughly.
• To clean laminate floors after repair, use special detergents for laminate surfaces. After applying them, it will shine and smell fresh. It is better to use a microfiber cloth to wash such a coating. Do not use too much liquid so that the surface does not deform.
• You can remove construction dust from the parquet floor with the help of special parquet cleaners, which are sold in hardware stores. Wipe the parquet with a damp cloth soaked in the solution. Make sure that excess moisture does not get on the parquet, as it may deteriorate. After use, do not rinse the solution, as the floor will be covered with a protective film that adds shine.

By using these cleaning tips, you can effectively remove the dirt left after the renovation. By applying these proven methods, you will make any surface shine with cleanliness.

How to quickly clean the floor after repair

Floor cleaning after renovation
Washing parquet
Laminate washing
Linoleum washing

When repairing, various dirt, dust and debris are sure to appear on the floor. Even if the ceiling or walls are being repaired, the floor is still contaminated with residues of paint, plaster and other materials. For this reason flooring after work, you will definitely have to wash it especially carefully.

The choice of detergents directly depends on two factors - the material of the floor covering and the type of pollution. For a good and high-quality cleaning of the floor surface, you need to choose the best cleaning method and suitable cleaners. About how to wash the floor after repair, and will be discussed in this article.

Floor cleaning after renovation

Cleaning the floor from dirt is often problematic, so cleaning has to be done several times.

The general floor cleaning algorithm is as follows:

• First of all, an ordinary soap solution is used, which must be applied to the surface and left for a while;
• Next, detergents suitable for the surface are used, and at this stage maximum efforts must be made to wipe off the dirt;
• Then the floor needs to be washed again, but now ordinary warm water will be used for this.

In the process of washing, it is necessary to ensure that the rag is relatively clean - do not smear dirt on the floor.

Sometimes, after work, only stubborn dirt remains on the floor, which is difficult to wash. To solve this problem, you can use folk remedy- add some kerosene to the water. Its presence in the solution allows you to eliminate even the most serious pollution.

Of course, the use of kerosene for washing the floor has a drawback - an extremely unpleasant and persistent smell. To get rid of it, you will need to wash the floor again by adding a glass of vinegar to the water - the smell will disappear completely.

If there are traces of whitewash or plaster on the floor, another method will be required. Before you wash the lime from the floor, all solid residues that can be swept away with an ordinary broom are removed. Next, the floor is cleaned with any dishwashing composition.

It will not work to completely eliminate all traces of whitewashing in this way, so the next step is washing off the dirt with warm water and salt. The resulting mixture is one of the best answers to questions about how to clean floors after whitewashing.

If after that there are stains on the floor, then it is necessary to add a little potassium permanganate to a bucket of water, after which the composition will become bright pink. After washing the floor with such a composition, the stains will disappear.

How to wash the floor after repair - cleaning various floor coverings

Washing parquet

Before you wash the parquet after repair, you must first find out what type of pollution you have to deal with - the method of cleaning the surface will depend on this.

Ordinary water-soluble dirt (putty, whitewash) is removed with ordinary water and a small amount of detergents. That is why special preparation and long reflections on how to wash the putty from the floor will not be required. In addition, the use of water to wash off dirt in the case of parquet is also justified for the reason that parquet is not afraid of moisture and is excellent for wet cleaning.

It will be much more difficult to deal with paint or glue that has fallen on the parquet.

Here you will have to use the following recommendations:

• To eliminate serious contamination, solvents are used, but it is necessary to act with extreme caution: solvents can damage the top layer of the parquet and thereby render it unusable;
• It is best to use mild formulations - white spirit, kerosene, methyl alcohol or substances for the care of stoves;
• To wash off dirt, a small amount of solvent is applied to the dirt and rubbed, and the sooner this is done, the easier it will be to remove the stain;
• Before removing dirt, it is better to check how the solvent will work on a small inconspicuous area of ​​\u200b\u200bthe coating.

In addition to the methods of washing off dirt on the parquet, you need to know what methods of influence on this flooring are prohibited:

• Parquet should not be cleaned with coarse brushes and metal scrapers: these devices can damage the varnish layer, thereby completely ruining the coating;
• When wet cleaning, you need to monitor the amount of water used: parquet can be washed, but an excessive amount of water can make it unusable;
• Detergents containing abrasive particles or aggressive solvents should not be used to wash parquet - its surface is not designed for such loads.

Laminate washing

Laminate flooring, like any floor covering, is susceptible to various types of dirt. Eliminating them can sometimes be problematic, but if you choose the right cleaning agent, then there will be no special problems.

To decide how to wash the laminate after repair, you need to understand what kind of dirt you have to deal with.

Depending on the type of contamination, the laundering process of the laminate will look like this:

1. If paint has got on the laminate flooring, then it is best to remove it with white spirit, which is well suited for such contaminants. good option cleaning agent will be automotive chemicals, with the help of which bituminous stains are easily eliminated. Wiping off the paint should be done with soft materials - any abrasive products will damage the surface of the laminate, so they should not be used.
2. Sometimes, during repairs, mounting foam gets on the floor. For rubbing it, Dimexide is used, which can be found at any pharmacy. First, the drug is applied to the stain, and after a while, the dirt is carefully removed with a sponge and spatula. Be very careful not to damage the laminate.
3. On the laminate sometimes after the repair there are black characteristic marks left by the shoes.

   Water will not work here, but an eraser is fine. It is enough just to gently rub the pollution to completely get rid of it.

In any case, after removing the dirt, the floor must be washed, for which laminate cleaners and a wrung out rag are used. After washing, there will be no streaks or dirt left on the floor.

Linoleum washing

On linoleum, too, there are always various traces of dirt that need to be eliminated. Laundering of linoleum is always carried out with clean warm water. In order to easily and efficiently wipe off all dirt, it is necessary to constantly change the rag - otherwise the floor will be covered with stains, which are subsequently quite difficult to get rid of (read: “How to wash linoleum from dirt - cleaning options”).

Soap is often added to the water, which simplifies the process of washing linoleum. What can not be done is to use soda - it has a negative effect on the surface of linoleum, significantly speeding up the process of its fading.

If wet cleaning did not give the desired result, then you can use one of the following methods:

• Turpentine is well suited for cleaning, which makes it possible to qualitatively eliminate most contaminants;
• To eliminate large spots, you can use moistened chalk powder;
• Matte stains can be removed with a special mastic, which is available in many hardware stores (mastic can be replaced with linseed oil, which has a similar effect).

By choosing one of these methods, before washing the lime from the floor, you can reliably and efficiently remove all contamination.

Conclusion

Washing a dirty floor after repair is far from the most a big problem. If you know how to clean the floors after repairs without streaks and carefully clean the surface, then there will be no problems.

When the repair is completed, the question arises: how to wash the floor from construction dust? Often, standard flushing does not help, but only causes new complications.

Many companies offer specialized cleaning products, but not all of them work equally well.

Litter settles after whitewashing, installation, using a drill. Overall elements are easy to remove without additional substances, while small particles are not removed even for 3-4 times.

In this article, we will talk about most of the options for removing dirt after repair.

Training

Have you encountered the problem of floor contamination after construction work before?

If your answer is yes, then we can say with certainty that in the first place the problem is related to poor preparation for repairs.

Before the beginning repair work it is better to stock up on film, polyethylene or newspapers that cover the flooring.

Advice! Paper is not a good cover, because gaps form between individual sheets. A large amount of litter will penetrate into the gaps.

Any coating will not completely provide protection, but it will significantly reduce the degree of pollution.

If you forgot to protect the flooring, do not despair: there is a huge variety of cleaning products and methods that can effectively remove all the dirt.

Before starting work, it is necessary to protect your hands from the aggressive effects of cleaning mixtures. This is where rubber gloves come in handy.

If there is a lot of plaque, and its particles are small, it is recommended to use respirators or special protective masks. Thus, you can protect your respiratory tract from dust, which can adversely affect the body.

Small furniture should be taken out of the room, and it is better to move the overall furniture.

Tools and stages of plaque removal

Putting in order various coatings requires careful selection of tools and materials.

What will be effective for tiles may harm the parquet or not at all help with the processing of tiles.

In most cases, the following materials will be needed to eliminate litter:

• buckets and other containers;
• washcloths;
• special wipes for cleaning;
• vinegar;
• edible salt;
• kerosene;
• ammonia;
• cleaner (preferably organic);
• means for washing dishes and tiles;
• washing liquids;
• substances for cleaning wooden surfaces.

Regardless of the complexity of the contamination, cleaning is carried out in several stages.

1. First, large debris is removed, whether it be large layers of plaster or pieces of brick. After that, from the corners to the center of the room, sweep the dirt with a wet broom.
2. With the help of a wet rag, washing is carried out in several approaches.
3. Next, you need to add a cleaning agent to the container with water, and then rinse the floor again.
4. After repeating this procedure several times, you can wipe the surface dry with a regular microfiber cloth.

Features of different surfaces

Small debris quite often brings a lot of difficulties after repair. It clogs in the cracks, and after getting wet, it can form hard deposits.

Processing is complicated by the fact that different methods are used for each coating, and the wrong selection of materials can greatly harm.

Also, before starting, they remove all furniture, tools and auxiliary materials, thereby clearing the field for themselves.

Painted wood flooring

If your house has a painted floor, then when cleaning it is worth taking care that the coating layer is not damaged and does not lose its properties. There are several methods:

• Ammonium chloride. Mix these components in the ratio of a tablespoon of ammonia per liter of water. Using a rag, the area is wiped, after which it can be soaked with a small amount linseed oil and wipe again. Thanks to this, the paint will shine.
• Acid agent. Depending on the complexity of the contamination, the substance is dissolved in a ratio of one to five, and more solution can also be used. Next, the resulting mixture is applied and left for a while. After that, the substance is mixed well.

These are the most common and proven effective ways to bring the room in order. If you don't want to destroy your flooring, it's best to follow the directions.

Advice! Upon completion of the cleaning, you can cover the area to be treated with a simple solution: add a glass of vinegar to one bucket of water. In this way, you can give the surface a shine.

When all procedures are completed, it is better to complete them with a dry cloth to avoid the appearance of streaks and stains.

Linoleum

Linoleum is one of the most common types of flooring. Its main advantage is the structure, resistant to any damage.

In this regard, purification can be performed using any method. The most popular among them are:

• Washing vacuum cleaner. Unfortunately, the relief structure gets dirty more than the glossy one. Debris is clogged in its “pores”, which is not easy to remove with an ordinary napkin. If you do not have a washing vacuum cleaner at home, you can rent one. You can also replace this device with a regular brush, however, working with it will be a rather time-consuming process.
• Vegetable oil. Taking a solution of oil and water in a ratio of one to a hundred, you can clean it with a simple rag. After that, take a container with clean liquid and add one glass of vinegar to it. With this solution, we clean again, after which we wash the surface.
• Kitchen salt and detergent. It will help in the fight against lime dust. One tablespoon of the substance is diluted in a bucket and cleaning is carried out. After that, add half a glass of salt to a new container with the substance and wipe the area. Upon completion, you can wash the linoleum with plain water.

There are also a huge number of specialized cleaning products that will help to effectively remove dirt.

Advice! Wash with a well wrung out cloth, and the water should not be too cold or hot. Immediately after completion of the procedure, it is necessary to dry with a sponge or cloth.

You can not spill a large amount of liquid, otherwise the linoleum will begin to become covered with tubercles.

Parquet

Parquet is a rather expensive floor covering, and it is recommended to take all measures to protect it before starting repairs.

• With the help of a vacuum cleaner, all small particles are removed. It is better to use a nozzle with a soft structure.
• A special solution for parquets is diluted in a bucket. For this, 100 ml of the product is enough.
• The rag is soaked and squeezed well, leaving it slightly damp.
• After that, the area must be thoroughly wiped. It is not dried or wiped dry. The mixture will create a protective film.
• When removing dirt with a vacuum cleaner, you must act very carefully so as not to damage varnished surface. To give shine to the parquet, it can be wiped with mastic. But it is recommended to do this after careful processing.

Floor tiles

In the bathroom or kitchen, in most cases, the floor is tiled. After repair, debris enters the joints, and also forms a plaque.

Lime plaster brings great harm, which not only crumbles, but also leaves traces. To clean the tiles, use special substances for ceramics.

Cleaning is carried out in four stages:

1. About 100 ml of the product is consumed per bucket, which must be mixed well.
2. Wash in several approaches, constantly rinsing the rag.
3. As soon as the water becomes cloudy or dirty, it should be replaced.
4. We do not recommend wiping a well-cleaned surface dry, otherwise the mixture will not leave a shiny film on the tile.

It is not necessary to buy expensive detergents, it is enough to use a soap or powder mixture.

Vinegar can be used to remove serious dirt, such as lime deposits.

Advice! A cheap way to brighten and shine your tiles is to use a solution with lemon juice.

Summing up the entire article, it can be noted that the main requirement for cleaning the floor from construction dust is the selection of methods depending on the type of surface.

Products for cleaning any coatings are represented by a wide range, but improvised materials can also be used. The main goal is "Do no harm!".

There is a lot of housework, one of the rather difficult stages is washing the floors. But no matter how hard you try, there are often dirt on the floor that is not so easy to remove with a wet rag, stronger means are needed here.

So, all sexes are different, however, as are the methods of cleaning stains from the floor. We'll figure out.

Dirt on wood floor

To effectively clean a wooden floor, prepare everything you need, namely:

• soda;
• vinegar;
• sandpaper;
• stain;
• cotton swabs.

The procedure for cleaning a wooden floor from contamination consists of the following steps.

1. Rub the stains with sandpaper, remove debris.
2. Prepare a mixture for cleaning (it includes 1 liter of water and 3 tablespoons of soda).
3. Wipe the place of contamination with the prepared mixture, wait 1-2 hours and wipe again, and so on until the stains disappear.
4. Wait until completely dry.
5. Wipe the now uncontaminated area with a cotton swab dipped in vinegar.
6. Choose the right stain or paint.
7. Put it on the floor.

The considered mixture is good, but still not perfect. Sometimes you have to use a special chemical composition, which is freely available at the hardware store.

Before treating the floor with such a solution, the following manipulations must be performed:

• open windows;
• cover furniture;
• wear goggles, gloves and a respirator.

When all the necessary preparations are made, lubricate the contaminated area with a chemical composition using a brush. If parts of the coating are swollen, simply scrape them off. Just do it gently and carefully.

The last step that completes the floor cleaning procedure will be washing the area to be treated.

If necessary, the process can be repeated, only to use oxalic acid.

Secrets of parquet beauty

Before deciding what means to clean the stains on the parquet, you need to know how to properly care for it.

Caring for parquet flooring is simple and involves a few steps.

• Sweep the floor with a soft brush every day.
• Vacuum at least once a week.
• In case of excessive moisture, wipe immediately with a towel or damp cloth.

If the floor has been varnished relatively recently, within two weeks after this procedure, you can only clean the parquet with a vacuum cleaner, and forget about wet mops for a while.

But pollution, which is not so easy to deal with, is still unavoidable. Insidious spots appear and do not give rest. The process of dealing with them is difficult, and if it does not bring the desired result, it is also not very pleasant.

But, knowing the main secrets, it will not be difficult to remove even the most “harmful” stains.

Grease stains can be easily removed with:

• warm water with dishwashing detergent added to it;
• denatured alcohol.

But paint stains can only be removed with a water-alcohol solution in a ratio of 1: 3.

Wax on hardwood flooring is not uncommon and requires an ice pack to remove it. After freezing, it will easily move away, all that remains is to scrape it off with a non-sharp object to avoid damage. A similar procedure is the best suited for removing chewing gum, and in the case of tar or tar stains. And the chemical solution will deal with all the remaining traces.

Many parents are faced with pencil drawings on the floor. Creative children are, of course, nice, but painting on the floor does not cause such positive emotions. You should not worry and worry: "White spirit" will save the parquet from children's pranks. If it is not at hand, you can try to erase the art with toothpaste.

There is an opinion that blood leaves stubborn stains. Nothing like this. If the traces are fresh, they can be easily wiped off with plain water, but to remove old ones, ammonia must be added to the water.

Accidentally spilled nail polish is no reason to panic. The stain must be moistened with acetone, and then cleaned well with the rough side of the sponge moistened with alcohol.

Fruit stains are removed using two products that are in every home - this is water and detergent. The second component, if necessary, can be replaced with oxalic acid.

If rubber sole marks are a problem for your parquet floor, an ordinary eraser will come to the rescue.

It is easy to deal with stains on the floor, the main thing is to know what and in what situation it is necessary to apply. And then the procedure for cleaning the floor from dirt will be effective.