How to reduce the transition between tile and laminate. We make the joint between the laminate and the tile invisible. Using a cork compensator

Interest in this design of floors arises for a variety of reasons:

• the desire to zoning the premises by highlighting certain parts of a spacious room;
• separation of the coating into two parts in order to increase the service life of the material, at least in that area of ​​\u200b\u200bthe room where the intensity of walking of residents is much lower.

However, it will not be about how good this design is, but about how to join tiles and laminate without a threshold, doing all the work yourself. This method of laying both parts of the flooring requires the worker to be precise and accurate.

Defects that have arisen during work can be hidden with a special threshold, but even without its use, you can get a perfectly flat, uniform surface. The main thing is that the joint should not be noticeable during visual inspection and in the photo, as this will spoil the opinion about the quality of the work performed.

Preparatory stage of installation

The following steps must be taken before starting work:

• measure the thickness of purchased materials;
• prepare templates for laying;
• trace: mark the junction line on the floor.

After all of the above, it is necessary to decide which of the materials will be laid first. Experts will confirm that you can only start with tiles and nothing else. This sequence is due to the fact that the tiles have a standard thickness, and the laminate can be leveled during installation with a special substrate that will be uniquely used.

But what thickness the indicated layer will be, it is up to the owner to decide. Alignment will be much easier in this case.

You can rely not only on the substrate, but also prepare the surface in advance so that the connection of tiles and laminate without a threshold is as simple as possible (read: ""). If the laying is done on an equal basis with all the others repair work inside a clean, newly built building, you can level the height at the level of the screed.

Achieving the original design of the floors in the room, you can align the base for laying as the owner wishes. In this case, the room is easily divided not just into two parts, but an original pattern is created from two types of coverage.

Laminate in this case acts as a material that will be adjusted to the joint, since it is much easier to process. The thickness is equal to the selected substrate, as mentioned earlier. As for the location relative to the joint and the tile, the gap between the two coatings should be 1.5-2 millimeters.

The article is about how to join tiles and laminate without a threshold, which means that the seam will have to be sealed with a certain tool. The size of the seam is selected depending on the means by which the filling will be performed.

Features of the seam between coatings

There are two main ways to create a seam. Naturally, there is nothing easier than to connect a tile and a laminate without a threshold along a joint represented by a straight line. The only caveat in this case may be that low-quality tiles will have to be processed from the side where the connection with the laminate will take place.

However, the attractiveness of such a connection is low. In the photo, the room will not look original, and the guests will not appreciate the creative delights of the owner.

The non-standard curvilinear shape of the seam is not commonplace, but it is also much more difficult to perform work on laying the material.

The difficulty lies in a number of conditions:

• it is necessary to create a preliminary template completely similar to the contour of the seam line;
• the width of the butt joint must be observed regardless of the number and complexity of bends;
• the material must be cut out in advance and laid the first time, since it is completely impossible to level the tiles on the floor, and the laminate will not look aesthetically pleasing.

Joint processing methods

After you connect the laminate with tiles without a threshold, you need to seal the seam between the coatings. In this case, two main means can be used: sealant or cork compensator.

To replace part of the coating, it will be necessary to completely dismantle it by a rough method and lay a new one. When using, it is also worth knowing that the sealant dries extremely quickly, and therefore its contact with a tile or laminate threatens with unpleasant pollution. To eliminate it, you will have to work hard and perform all possible actions as quickly as possible.

If the joining of the laminate and tiles without a threshold is carried out using a cork compensator, then the owner will need to put a “thread” of the material into the seam. A variety of colors will allow you to choose a material that will harmoniously look at the junction of two materials.

The disadvantage is that any height difference will be noticeable to the naked eye and the "thread" will not fix it. Therefore, the use of a cork compensator is permissible only in the case of very high-quality laying of coatings.

Outcome

Maximum accuracy, patience and clarity of action will ensure high-quality coverage, regardless of how complex the pattern was conceived by the owner. If there are certain difficulties with installation, then you can always turn to specialists who will perform the work quickly and without wasting time and money.

A professional builder, based on the preferences of the client, will take responsibility for the purchase of materials, work, and also provide a guarantee of the quality of the created coating.

Quite often when functional zoning you have to join different floor coverings.

To use special structural solutions for this or a universal plastic joint filler is not only a matter of taste and personal preferences. Today we will talk about the scope and specifics of work with liquid cork and classic sills.

Levels, edge quality and materials - what we are dealing with

The solution of the question of the most correct way of joining different floor coverings begins with a comprehensive assessment of the scope of work. Of primary importance are both the quality of laying the floor in different areas, as well as its type, level difference and operating conditions. But first things first.

The fundamental difference between plastic joint fillers (cork, silicone) and hard linings (nuts, click systems) lies in the property of the latter to provide protection to the ends that are susceptible to moisture, dust and small debris.

Difficulties are also added by the circumstance when one of the joined coatings is arranged according to the floating floor system and does not have a rigid attachment to the rough surface. Most synthetic materials such as linoleum and PVC allure do not show pronounced shrinkage and expansion, but with MDF laminate it can be difficult. The joint in this case should have a compensatory purpose, that is, its width should be at least 0.5–1.5 mm for each meter of the coverage. How a gap of 15–20 mm will look like, sealed with a liquid plug - try to imagine for yourself.

We smoothly approached the basic rule for choosing between seam design options. If you want the most imperceptible seam filled with a plastic composition, take the trouble to bring both coatings to the same level in advance and exclude any differences of more than 0.5 mm. Also keep in mind that the use of plastic filler is not always possible, especially in spacious rooms where the floor is finished with wood or materials that have similar behavior with changes in humidity and temperature.

To summarize, if you are serious about using any plastic filler, be prepared for careful processing and precise trimming of the edges of the joined coatings. It is important to understand that if the finishing floor in both zones has already been laid, then, most likely, the moment has been missed, which means that it will no longer be possible to correctly and aesthetically fill the seam with a liquid cork.

Silicone and cork fillers

It is most reasonable to use plastic silicone fillers to mask forced transitions, for example, between linoleum in a room and tiles laid in a corridor. The conscious use of a liquid plug for zoning flowing spaces is the least beneficial, although customers and contractors have different points of view on this issue.

The optimal joint width for filling with a liquid stopper is from 5–7 to 15 mm. A smaller size will not allow filling the joint groove with high quality, because the liquid nut includes a fairly large cork crumb, and besides, its consistency makes filling thin cracks an extremely tedious process.

From this we can conclude that for the junction of tiles and laminate, this transition method is quite applicable only when the laminate is stretched no more than 10 meters from the junction to the opposite wall, taking into account the 10 mm seam under the plinth on the reverse side. We will consider a small exception to this rule a little later.

As for the structure of the coatings to be joined, the liquid cork is definitely not suitable for joining carpet with any other coating, as well as for filling joints between two linoleum sheets if the thickness of the latter is less than 3 mm.

Technique for sealing joints with plastic filler

For a qualitative reduction of two levels of dissimilar coatings flush, a certain basic reference point is needed. Usually it is taken as a coating rigidly fixed to subfloor: tiles, porcelain stoneware, regular or modular parquet. This part of the floor is laid first and carefully leveled to obtain as even a plane as possible.

The laid coating forms an open end. When laying, close attention should be paid to the accuracy of trimming, however, even the most zealous attitude to this process does not guarantee the reduction of the edge to a common line. Therefore, the open end is processed after laying using a conventional abrasive stone or wheel if the edge has a radius shape. You have already understood that the maximum trimming accuracy at the first stage reduces the complexity of processing at all subsequent ones.

Next, the second part of the coating (usually floating) is brought to a common level with the first zone. For this, either substrates of different thicknesses are used, as is the case with a laminate, or, if the difference in levels exceeds all permissible values, fill the preparatory screed with a self-leveling mixture.

It should be borne in mind here that for high-quality sealing of the seam, it is important to absolutely match the levels on the adjacent 50 cm of the coating, then slight differences are allowed along the floor. Therefore, when leveling the mixture, home-made slats-thicknesses are used, or the dried screed is brought to the desired level by grinding or wiping with tile adhesive.

As for the technique of filling the seam - it is extremely simple. First, all dust and debris is swept out of the gap, then, if recommended by the manufacturer, the joint is opened with a special primer. You just need to fill the gap with the composition, while it is advisable to pre-squeeze the mixture from the tube into a more convenient container. Clamp the cork end-to-end as carefully as possible. After filling one to one and a half meters of the length of the seam, the excess cork is removed with a spatula, and the formed stains are removed with a wet rag.

Sometimes it is allowed to fill seams with a plastic nut, the thickness of which exceeds 20 and even 30 mm. Such a transition is performed using a strip of solid cork compensator, which is immersed in the joint after it is filled with a plastic compound. The surplus can be easily cut off with a knife after drying.

Nuts and pads

All kinds of "hard" sills are installed where plastic embedding is not relevant in principle. Level difference of more than 1 mm, torn edges, pronounced linear expansion of the coating - these are just some of the indications for their use.

The material of floor coverings is also of decisive importance. For connecting linoleum, a flat docking pad is almost the only reliable transition, not counting the solder joint. Solid wood floors also require the use of appropriate fittings (also wooden) for reasons of uniformity and solidity.

In general, hard transitions can be divided into three basic types, which have a fundamental difference in the installation process.

1. Straight sills hidden installation mounted upon completion of the device of both parts floor covering. Installation is carried out on ordinary dowels, the nail heads of which are pre-attached in a hidden mounting groove.

2. Aluminum sills are installed along the installation of the finishing floor of both zones. Their wide shelves at the bottom prevent pulling out, but it is almost impossible to get them under the coating after laying. Such sills cannot be replaced.

3. Straight and flexible click systems can be installed both during the laying of floor coverings and after its completion. These sills can be replaced over time if their face wears off or becomes unusable.

The latter, by the way, is the benefit of rigid butt transitions: they are more resistant to destruction even in areas with high traffic. At the same time, the plastic filler can be replaced relatively painlessly for the rest of the floor.

During the repair process, the question "How to join the laminate and tiles?" arises at a time when it was not possible to reach a compromise. On the one hand, to argue with practicality ceramic tiles impossible. On the other hand, the price for high-quality material is too high, and you want that comfort that only parquet can create. And this is where the idea is born to use two completely different coatings in the same room. Fiction? Not! beautiful and practical solution!

Or maybe tiles?

Builders are unanimous: the most durable flooring is ceramic tiles. Designers also agree with them, saying that along with durability and ease of maintenance, tiles are distinguished by such a variety of textures, shades and patterns that they can be used in any room. However, laminate flooring also has its advantages.

• Firstly, the laminate is distinguished by good noise and heat insulation properties. It is pleasant to walk on it with bare feet. In addition, falling on such a floor, dishes, a tablet or a mobile phone will not break, but hitting a tile is easy.
• Secondly, it's the price. The minimum cost per square meter of laminate is 400 rubles, about 300 more will have to be paid to the master for laying the substrate and the flooring itself. Total 700 rubles. Buy the same floor tiles You can even at a price of 300 rubles per square meter. But its installation will require much more time and more skill. And therefore, tilers will take at least 1000 rubles for work. Total 1300 rubles per 1 square meter. Thus, choosing a laminate for a room of 20 m2, you can save at least 12 thousand rubles!

Laminate or tile: when is the saving justified?

And yet, even having opted for a parquet board, it is advisable to put a stronger material in places that are more prone to abrasion and other mechanical influences:

• in the hallway - around front door;
• in living rooms - by the fireplace, where soot and even sparks on the flooring are likely;
• in the kitchen - near the sink, stove, cutting table.

Thus, you can get the perfect floor covering: practical, durable and quite inexpensive. The only thing you need to immediately think about is how to join the tiles and parquet board so that the result is pleasing to the eye, and the joint itself does not cause inconvenience in operation.

The combination of flooring as a design solution

In addition to achieving purely practical goals, the combination of different floor materials can also serve as a kind of highlight. For example, in this way it is possible to delimit zones in a studio apartment or in a spacious kitchen to separate the dining area from the cooking area. But owners of tiny apartments should not think about how to join tiles and linoleum or tiles and laminate! Trying to split up an already small space, you can visually make the room even smaller.

Another thing - bright, spacious rooms. Here you can demonstrate your design talent to the maximum. For example, a wavy path of a contrasting shade in the living room will not only protect the places with the greatest traffic from abrasion, but will also become the main decoration of the room. And in the nursery it will be appropriate in the area where strollers and scooters, bicycles and rollers are waiting in the wings.

Methods for decorating the junction of laminate and tiles

To the question "How to join tiles and parquet?" Each builder has at least 4 ready-made recipes:

1. using a decorative nut or molding;
2. end-to-end without a nut;
3. using construction foam and sealant;
4. using a cork compensator.

Each method has its advantages and disadvantages and is good for a specific situation.

Installing a nut or molding

In a typical apartment, it most often comes into contact with tiles in doorway between the corridor and the bathroom or toilet. But in this case, the question "How to connect tiles and laminate?" not even voiced, because the specifics of the aforementioned premises are such that the best, and most often, the only justified solution would be to install a high wooden threshold.

But the use of low sills and moldings is advisable in cases where it is not possible to dock 2 floor coverings perfectly evenly and at the same height. And the main task of these decorative elements, with which they do an excellent job, if the height difference does not exceed 10 mm, is to create a neat transition and hide the imperfections of the seam. In addition, it is much easier to install a molding than to achieve a butt joint, and during operation, the threshold will always protect the edge of the laminate from peeling.

Varieties of decorative sills

Traditionally, sills are made from:

• tree;
• plastic;
• aluminum.

Wood is the most familiar material and fits perfectly into any interior, especially if used. It’s just that only a straight joint can be decorated with a wooden profile. But if the connection line is made in a semicircle or, more interestingly, a snake, you will have to use plastic or aluminum moldings, which come in a variety of configurations. Also on sale you can find decorative sills with additional features, for example:

• anti-slip with a ribbed front surface;
• rounded for joints of floor coverings of different heights. Such moldings are installed at a slight slope.

How to close the joints between laminate and tile with molding

Decorative sills are attached to the surface of the subfloor with dowels or self-tapping screws. At the same time, depending on the design of the molding, the fasteners may remain visible or be hidden under the decorating strip. In any case, if it is possible to purchase a prefabricated threshold, consisting of a mount and a removable lining, preference should be given to it.

Important! Laminate, like any other wood flooring, requires compensation for expansion when laying in case of changes in humidity and temperature in the room. Therefore, it is impossible to lay it exactly end-to-end! A small gap must be provided around the entire perimeter - about 5 mm.

Installation of flexible moldings

When it is not possible to find suitable sills, one thing remains - to purchase flexible moldings made of soft plastic. Their installation is quite complicated and painstaking, and it takes no less time than laying a laminate. First, the plastic threshold is carefully heated with a building hair dryer. And only then, when it softens and can take any shape, its lower part - the groove-clip is inserted into the seam and the decorative insert is snapped onto it. After a few minutes, the molding cools down and acquires the necessary rigidity.

How to connect tiles and laminate butt without a threshold

At first glance, if the connection line of two floor coverings has a complex shape, it is easier to arrange it without a threshold, end-to-end, simply by rubbing the seam with grout. But in practice, it turns out that the implementation of this idea requires great experience and professionalism, because even a difference in levels of 2 millimeters will be visible and tangible here. In addition, even minimal burrs on the laminate are also unacceptable.

Use of sealant

One of the options for designing a butt joint is to use mastic, construction foam or sealant. The advantage of the method is the excellent concealment of the seam, even if the seam line has a great depth. In addition, silicone is available in different colors, which allows you to make the seam almost indistinguishable in color from the entire floor. But there are also disadvantages:

• the sealant is not easy to use and requires a highly skilled craftsman. In addition, its excess is very difficult to remove both from ceramic tiles, especially if it is from laminate;
• the reliability of such a butt joint is low. Therefore, a seam made with a sealant is recommended to be updated every 2-3 years.

Making a butt seam of complex shape

In practice, it looks like this:

1. Laying of tiles and laminate on the floor is carried out in such a way that at the future wavy joint, the latter slightly overlaps the tile.
2. The time required for the tile adhesive to dry is maintained.
3. A cardboard template for the future seam is created.
4. Using a template, the joint line is drawn on the already laid laminate, which is then partially disassembled.
5. The tile is cut along the drawn line with a grinder with a diamond wheel.
6. The substrate is removed a few centimeters from the tile.
7. Using building silicone, the laminate is glued to a pre-primed screed.
8. The seam is overwritten, after which the strength of the resulting joint is checked.

Using a cork compensator

To date, a cork compensator is the best way to arrange a joint between a laminate and. It harmoniously fits into any interior and looks very dignified. The only drawback of the compensator, which is simply inserted between two finishing materials, is the high requirements for the seam itself, which must be perfectly even not only in width, but also in depth.

/page/pub/view/kak-sostyikovat-laminat-i-plitku

How to join laminate and tile

The question of how to properly arrange the junction of tiles and laminate quite often arises during repairs. In addition to some technical points that you will need to pay attention to, each case may differ depending on the type of premises and the design approach to its design.

Peculiarities

Usually the need to design a beautiful and practical transition from one material to another arises when designing transitions between rooms. For example, in the kitchen, in order not to spoil the laminate in the corridor with moisture, tiles are laid. Less often, various floor coverings are used to divide a large room into zones: tiles are laid in places with high humidity or the risk of mechanical damage, and laminate is placed in other areas.

Accordingly, the junction of tiles and laminate must be closed so that it does not spoil appearance rooms, did not crumble and did not collect dust, sand and other small debris.

So, connecting different types of flooring has several main advantages.

• First, because each material is in its place and performs its intended function, it wears out less, which increases its service life and strength.
• Secondly, this design gives the owner of the premises the opportunity to save on more expensive materials, giving preference to a product that costs less.
• Thirdly, with the proper design approach, the transition from one floor covering to another within the same apartment can be a stylish and unusual solution.

The main disadvantages are the difficulty of joining two types of flooring and possible difficulties in choosing the right color.

Floor types

There are many types of flooring available on the market today. All of them have their own characteristics, maintenance rules, and if the owner decides to use a combined floor in his apartment, then during the repair he will need to take into account the specifics various materials.

Laminate

Laminate flooring is made by pressing high pressure hardboard or chipboard with a backing and a top film layer.

It successfully imitates wooden parquet, stone or metal.

Ceramic tile

Tiled flooring is usually used in the bathroom and toilet, in the kitchen and, a little less often, in the hallway.

It is quite resistant to abrasion, easily transfers high humidity and does not expand at elevated temperatures.

This resistance to mechanical and chemical damage gives the tile a special durability. Often ceramic tiles (especially when water gets on them) can be very slippery.

PVC tiles

In terms of composition, this type of flooring is largely similar to linoleum and consists of similar materials. PVC tiles do not require complex laying conditions, almost do not slip, are able to provide very good sound insulation and, importantly, are moisture resistant and do not crack. Even in the event of mechanical or chemical damage to one or more tiles, a complete replacement of the coating is not required: it is enough to eliminate the damaged areas and lay new ones in their place.

At a relatively low price, PVC tiles also have some disadvantages: insufficient environmental friendliness and instability to chemicals.

Porcelain stoneware

Porcelain stoneware flooring is characterized by increased strength, almost does not scratch. Porcelain stoneware is resistant to a variety of chemicals and withstands high temperatures. More dense slabs of this material are able to withstand the weight of the car, which allows it to be used even in the garage.

It is clear that these are not all finishes. However, the materials listed above for flooring are most often used in rooms with various types flooring, and it is they who usually cause the need to design joints when moving from one material to another.

How to connect correctly?

To properly join two types of floor coverings (so that the joints do not clog with dirt, dust and small debris and do not make residents stumble), you need to follow a few simple rules.

First of all, joining different materials will become much easier if they are of the same thickness (it can be quite difficult to choose this taking into account the colors, patterns and desired material), or at least not very different.

If the coatings in any case have a drop, then you can remove it (if it fluctuates up to 10 mm) with the help of a threshold.

The main way to combine a combination of laminate and ceramic tiles is to attach materials and, if necessary, cut out the desired shape.

Modern methods

When combining multi-level types of flooring, the owner who decides to carry out repairs may experience some difficulties in combining them.

Butt jointing is possible if both materials have the same thickness and texture.

However, if you want to combine laminate and tile flooring within the same apartment, it is very difficult to make a seamless connection, since the coating often turns out to be multi-level.

If the height difference between the two materials does not exceed 10 mm, then you can safely try to seal the connecting seam with a straight threshold.

It will smooth out this discrepancy and can become a stylish design solution: decorative thresholds are made of wood, aluminum and plastic, and their texture often resembles wood, stone or metal.

If the difference reaches 15 mm, then it would be best to use a flexible threshold. It is made of plastic with a rubber base, and its direct installation should be carried out at the time of laying the coatings. At the same time, the threshold itself is heated with a building hair dryer, which gives it the opportunity to take any necessary shape.

In the doorway

It is not difficult to make a fastening of the docking threshold in the doorway. At the junction of ceramic tiles and laminate with an interval of 10 to 15 cm, holes of approximately 6 mm in diameter must be made using a drill.

The threshold itself is cut in accordance with the width of the opening, and dowels are driven into the holes, which, as a rule, come with the threshold.

Insert the self-tapping screw heads into the central groove of the nut rail, at the same distance as the dowels, align and hammer the nut into place.

Varieties of separators

Separators are of various kinds. Their choice, in turn, depends on the personal preferences of the owner of the coating, the height of the difference between different coatings and some other factors.

Transitional threshold

The use of a transitional threshold when connecting two different materials is the simplest and most common option at the moment. The sills differ in color, shape and texture, if desired, you can find a sill that blends perfectly with tiles and laminate.

They are suitable for coatings of different widths and easily hide errors.

Usually such sills are made of plastic, wood or aluminum. At the same time, aluminum products are the most durable of the three options. The tree is quickly erased and retains an attractive appearance for a little more than three years, plastic completely becomes unusable after an average of a year and a half.

The sills can be equipped with hidden fasteners. Then they will be fixed on the floor with the help of a special fastening bar that will hold them on itself.

However, it is not always necessary for the owner to use a hard and straight threshold. If the design solution includes curved lines and semicircles, then a flexible threshold can be used to join the laminate and tiles.

This type of docking profile has two more subspecies: plastic and metal flexible profiles. It is important to note that in the case of using the second type of connector, the thickness of both floor coverings should be approximately the same, otherwise you will have to remove a small layer from one of the materials.

Mounting foam or sealant

Silicone, mounting foam or sealant is usually used if the transition between the two materials is too wide and deep, and the grout cannot cope and eliminate it. Foam or sealant is poured into the hole and filled. After that, it is necessary to wait for the substance to solidify and get rid of its excess on the surface with a knife. From above it would be nice to cover the remaining strip with grout for ceramics.

It is important to remember that both materials must be the same width in order to apply this method, otherwise the appearance of the transition will look uneven and unattractive.

Also, during the repair, it is worth showing special care, because partial dismantling and correction of the mistakes made will subsequently be impossible.

Cork compensator

Cork compensator is a self-adhesive strip of cork that is attached to the edges of the laminate and ceramic tiles. This type of separator is flexible and soft, which allows it to compensate for the movements of the coatings relative to each other, without damaging either the tile or the laminate.

The cork compensator is installed directly at the junction of two coatings.

Being treated with a hermetic composition, it is able to completely prevent moisture from entering inside.

Liquid stopper

Liquid cork will not crack, and due to its structure, it is able to seal even small joints between different materials without damaging the finishing surface.

The width of the seam that the liquid plug can fill ranges from 5 to 15 mm. It is simply impossible to fill a smaller width, because the liquid cork consists of rather large crumbs, and in the case of a larger width, the gap will simply be sloppy and unreliable.

How to fix?

Depending on which joint design option will be chosen by the owner, there are several basic ways to fix the tile and laminated coating at the convergence point.

threshold

First of all, you need to install floor coverings and dock them. The gap between them should not be too narrow (so that a separator can be placed in it), but not too wide.

Holes are drilled in the floor at the transition point at a distance of about 10-15 cm from each other, into which plastic dowels must be placed.

After that, the threshold itself is superimposed on the butt line. It is fixed with self-tapping screws.

Sometimes, if a threshold with a hidden mount is used, a mounting plate is used instead of self-tapping screws. It is installed on the floor, and then its fasteners snap into place on the nut itself.

In addition, there are options for sills that are installed without drilling.

For example, it will be enough to cut a variety of flexible metal profiles to the required size and glue them to the junction. The main thing is not to forget to remove excess glue from the surface that protrudes on the edge of the nut.

Sealant or mounting foam

To begin with, a joint line is marked, which the filler will hide, and the tile is placed so that its front edge protrudes slightly beyond this line. This is necessary so that you can later cut off the excess length and thereby adjust the dimensions of the tile as accurately as possible.

Then the junction is cleaned of construction and household dust, and a laminate is laid on the floor. Its height and width must be adjusted to match the dimensions of the tile.

Finally, the junction is filled with the chosen means: sealant, mounting foam, less often - glue or grout for the seam.

This method is more time consuming, but allows you to connect two types of flooring without drilling.

Cork compensator

The ends of the two materials are ground and adjusted. It is necessary to rid them of a variety of chips and cracks, after which the tile and laminate are located as close to each other as possible.

When the first part of the work is done, the cork compensator, using, for example, a screwdriver, is carefully pushed into the gap between the materials. Finally, the joint of the two materials and the visible part of the compensator should be treated with a sealant to prevent moisture from penetrating into it.

Liquid stopper

To begin with, the joint between the two materials is cleaned of dust and dirt. Sometimes the gap is pre-coated with a special primer recommended by the manufacturer to facilitate the pouring process. Then the cork is poured inside, and its excess is carefully removed with a spatula. After the composition has hardened, the seam must be wiped with a damp cloth.

How to choose the right option?

When choosing an option for designing a joint between a tile and a laminate, it is worth considering the features of the various separators and the features of the rooms between which the transition is made, or - if the materials replace each other within the same room - the appointment of different zones.

The threshold that separates the floor coverings does a great job of hiding where the two materials meet, although the transition from laminate to ceramic tile will look quite dramatic.

Importantly, the nut helps to hide and soften the transition from one material to another and thanks to a large number varied design solutions, colors and textures, perfectly fitting into any room. Best of all, the sills are suitable for the design of the transition in doorways.

It is worth remembering that the sills are of two types: straight (more resistant to mechanical stress) and flexible (allowing you to make round, wavy transitions between materials). The second type is suitable for zoning a room and will give originality to the appearance of the floor.

As for the material for the connection, it is also worth paying attention to.

For example, wood is suitable for almost any room, as it has a wide colors and stylish, in its own way classic appearance. But at the same time, it is quite rigid and is only suitable for straight sills.

The same problem haunts aluminum products, which are extremely durable and wear-resistant, able to withstand mechanical stress.

A much more elastic option is plastic, with the help of which the owner of the apartment is able to decorate the floor with various undulating transitions.

In addition, it has a huge selection of colors and textures, which allows you to choose a threshold that is ideal for any room and combined with any color of the floor covering. Finally, plastic, supplemented with rubber materials, is the most resistant to elevated temperatures, which allows it to bend and take the desired shape painlessly.

Installing two floor coverings without a threshold is a reliable option, although quite risky.

During the installation process, you need to be very careful, since the slightest mistake and inaccuracy can spoil the appearance of the joint between the materials, make it uneven and ugly. There are several options here: a one-piece joint (installed with grout), an almost invisible joint (ideal for places with a small area of ​​\u200b\u200bmaterial contact), a joint using a cork compensator.

To date, there are a huge number of materials to create maximum comfort in your home. Most homes use several types of flooring. For example, in the living room the floor is covered with carpet, in the hallway they use laminate or parquet, and in the kitchen - tiles. At the junction of various floor coverings, a joint is formed, which not only spoils the appearance and aesthetics of the interior, but also collects dirt and various foreign objects. To make everything look beautiful and practical, the joints between the tiles and the laminate are closed. There are several ways to do this, which will be discussed below.

When and why is it necessary to use different types of floor coverings?

Each material that is used as a floor covering has certain properties and characteristics, and also performs different functions. Carpet is very soft and cushions the fall of small children, so it is great for a child's room. The tile is water resistant, making it a great solution for kitchens and bathrooms. Parquet and laminate give the interior a more elegant and expensive look. All these materials are presented in a wide range in specialized stores.

The use of several types of flooring allows you to conditionally divide the room into different zones. This is especially true in the kitchen. The cooking area can be tiled, since it does not absorb water and grease, which will certainly drip onto the floor during cooking, and it is better to use a laminate for the eating area. And in order for everything to look aesthetically pleasing, the place where there is a docking of tiles and laminate should be closed.

Basic docking methods

Before you start laying several types of flooring, you need to decide where the border between them will be, as well as how it will be closed. To date, there are two main methods for joining various materials:

• rectilinear;
• wavy.

Each of the methods has certain features. And in order to choose the most suitable of them, you need to have a detailed idea of ​​\u200b\u200beach type of joint.

straight joint

Straight joint line suitable for doorways, arches and visual delimitation of space into different zones within the same room. This type of joint can only be used if the gap between different floor coverings is no more than five millimeters. A threshold is best for this type of joint, as it will hide any unevenness resulting from trimming the flooring.

Wavy joint

Wavy joining of tiles and laminate is more difficult to implement and requires certain knowledge and skills. Most often, it is used to delimit a room into separate zones or create a "path" passing through the room. In addition, the joint between different types of flooring of the wavy type is very often used in interior design and allows you to give the interior an original and aesthetic look.

If you decide to use different materials for the floor and want to close their joints with a wavy joint, then it is better to do this with a special template made of cardboard. In addition, if the shape of the joint is very complex, then special equipment may be needed to trim the materials, so you should think very carefully and realistically evaluate your strengths.

threshold

You can also hide the joints between tiles and laminate with the help of a threshold. This is the easiest and cheapest way to give the interior a more attractive look. The advantage in favor of using a nut is that this element can be made of plastic, wood and metal, so you can choose the perfect solution that will harmoniously fit into the interior.

To date, there are the following types of thresholds for the junction of laminate and tiles:

• straight;
• curved;
• flexible.

Straight lines are used to mask joints when moving from one room to another, curved ones are most often used in various design projects, and flexible ones are made using a special technology and have a rubber base, which allows you to give the thresholds any shape and hide joints even in hard-to-reach places.

The sills are very easy to install. Their fastening is carried out with the help of dowels, which can later be hidden by a decorative strip, which achieves a more beautiful and elegant look.

Masking gaps without a nut

This design of the junction of tiles and laminate is quite complex and requires very high accuracy and accuracy in the performance of work, so it makes sense to resort to it only when you need to make a figured connection.

The first step is laying the laminate and tiles. In this case, one material should be laid slightly overlapping on top of the second. Then the marking of the joint boundary is applied. To make everything smooth and beautiful, it is recommended to apply markup using a template. When the line is drawn, the laminate is cut and the flooring is laid. At the same time, if you want both types of flooring to lie on the same level with each other, the substrate must be removed from the laminate. To give aesthetics, the joint of the laminate and tiles without a threshold must be rubbed.

Masking joints with mounting foam or sealant

Using this method, you can remove large gaps between various coatings, which are filled with mounting foam or a special silicone-based sealant. In this case, the laying of laminate and tiles is carried out in the same way as when masking gaps without a threshold. The only difference is that the slots are pre-filled additional materials. If you are using silicone sealant, then on sale you can find several of it color options that will match the color of the flooring.

When working with foam or sealant, you should not fill the gaps with too much building material, because if there is a lot of it, it will come out of the gap. If the excess foam or silicone is not immediately removed, then after they harden, it will be much more difficult to do so. If there is not enough material, then the floor covering will be poorly fixed, and the joints between the tile and the laminate will be constantly clogged with dirt.

In addition, when using foam or silicone, one should take into account the fact that they tightly fix the floor covering, so it will not be possible to replace part of the floor in the future.

Cork joints

Cork joints between tiles and laminate are among the highest quality and most aesthetic. They are made using a cork expansion joint, which looks great with any kind of flooring. Cork can be dyed in any color, which makes this material versatile and allows you to implement any design ideas, regardless of the level of complexity.

It is worth noting that this material has a porous structure, due to which the color of the paint will look more saturated. In this regard, the junction will stand out and catch the eye, which does not suit everyone. In addition, it is impossible to eliminate various defects resulting from uneven cutting of floor coverings with the help of a cork compensator, so it can only be used if the cutting was performed by professionals using specialized equipment. Also, it is better not to use cork if the laminate and tiles were not laid on the same level, since this method of masking gaps on the floor will not only eliminate the defect, but also make it more noticeable.

Using moldings

Moldings are a special profile for joining tiles and laminate. In hardware stores you can find accessories in various colors, made of plastic, wood and aluminum, which allows you to use it in conjunction with any modern type of flooring. The main advantage of moldings is their versatility. They allow not only to hide the border between parquet and carpet, but also to eliminate various defects resulting from improper laying of the floor covering. With the help of fittings, you can hide even very large gaps from the eyes, as well as hide height errors. However, you need to buy fittings even before the floor is completely completed, in order to make sure that the fittings have the necessary elastic qualities and docking reliability.

So, you already know how to close the joint between the tile and the laminate, however, regardless of the choice of masking method, in order for everything to turn out high-quality and beautiful, you must perform correct styling flooring, which begins with the markup. If you already have a ready-made design project and it involves the use of parquet and ceramic tiles in one room, then after pouring the screed on cement, future zones should be drawn.

The first step is to lay the laminate, after which it will be possible to proceed with the tiles, however, it is necessary to strive to ensure that both materials are on the same level. This is quite difficult to achieve, but if you succeed, then masking the border line between both materials will be much easier. If you do not have such work experience, then it is better to abandon amateur performances and turn to professionals for help. Their services will cost much less than completely redoing the floor.

Conclusion

Today there are many various types floor coverings, which have certain advantages and disadvantages. However, the aesthetics of the interior in housing largely depends not on the flooring itself, but on how well the junctions of various materials were hidden. In addition, if the joints are closed poorly, then the laminate at the junction will rub off very quickly and lose its attractive appearance. Therefore, the masking of joints should be approached with all seriousness, because savings in this matter are simply inappropriate.

What type of flooring to choose for the floor is everyone's business. The most important thing is to make beautiful and neat joints that will look harmonious in the interior of the entire room.