home Climate

How to fix a hole in linoleum. How to patch a hole in a concrete wall? What to do with cracks in a concrete wall

Ceiling defects cannot be called a rarity, they are found both in new buildings and in old houses. Most often, the owners of living space are faced with a problem in the form of a hole in the ceiling, so you should study in more detail how to eliminate such a defect.

Causes of a hole in the ceiling

Ceiling defects in the form of a hole occur for the following reasons:

As a result of flooding or damage by a fungus, plaster falls in some areas. A layer of plaster may fall off if its thickness is more than 5 cm. This happens even when using modern materials. To prevent such a problem, the imposition of a plaster mixture in several layers with the obligatory laying of a reinforcing mesh allows.
As a result of the formation of cracks between the floor slabs, peeling of the plaster can also occur. The reason for this can be even a slight crack.
A hole can be formed due to the destruction of the cement plug in the hole for communication systems, for example, for heating risers, sewers and plumbing systems. A constant change in the temperature of the hot water riser can cause condensation to form, which destroys cement mortar used to close the hole.
A hole in the ceiling can be formed in the process of replacing the riser of communication systems. In this case, the task of how to close a hole in the ceiling near the pipe becomes relevant.
In addition, a hole can form in the stretch ceiling structure if it is careless when moving large objects. Panels made of plastic or gypsum practically do not tolerate mechanical stress.
A hole in the suspended ceiling may appear at the junction of the structural elements with the walls.

Ways to fix holes in the ceiling

When looking for solutions to the question of how to fix a hole in the ceiling, the type of ceiling structure should be taken into account.

The question of how to close a hole in a cassette-type ceiling can be solved very simply, it is enough to replace the damaged cassette. Elements of this design are inexpensive and are sold in almost all hardware stores. If it is not possible to purchase the necessary element, then you can put a lamp or a ventilation grill in this place. In addition, you can replace not one damaged panel, but several elements, creating a pattern of plates in a contrasting color.

Damaged PVC panels are more difficult to replace, however, in this case, it is also possible to do the work yourself. In the event of a similar situation, the dismantling of several panels is required due to the peculiarities of their fastening.

Sealing gaps between ceiling and walls

If during the operation of the plasterboard ceiling a gap has formed between the structure and the wall, then to resolve the issue of how to close the hole in the ceiling, you must perform the following steps:

The edge of the drywall sheet adjacent to the wall is cut at an angle of 45 degrees.
Fill the seam with gypsum-based putty and dry thoroughly.
Next, the putty is treated with sandpaper and the seam is fixed with paper tape with an adhesive side.

If a gap has formed between a concrete floor slab and a brick plastered wall, then the following measures are assumed:

The resulting gap is expanded to 1 cm.
Cover with a special primer with a brush. In this case, it is best to use concrete contact or its equivalent.
Next, the gap is filled with putty on a gypsum or acrylic base.
A serpentine tape is laid over the putty to strengthen the seam, trying to press the material into the putty mixture.
The corner is leveled with a spatula and left to dry completely.
The repaired area is treated with fine sandpaper.

How to fix a hole from a fallen piece of plaster

If for some reason a hole is formed in the ceiling from fallen plaster, then you can use several methods.

There is the easiest way to solve the problem than to cover up a hole in the ceiling, it is simply covered with putty. However, there is no certainty that a similar problem will not arise again.

For this reason, it is best to use a more time-consuming, but reliable option. It involves doing the following:

Before closing a large hole in the ceiling, the hole is treated with an antiseptic solution that prevents the formation of fungus.
Then the working area is covered with a layer of deep penetration primer. As a result of this event, the surface around the hole is strengthened and the degree of adhesion of the putty to the base increases.
The primer is dried and putty is applied to the problem area. It is best to perform the last action 2-3 times, while each layer should be well dried.
At the end, the treated area is ground and coated again with a primer.

Fixing cracks between floor slabs

If a gap appears between the concrete slabs of the ceiling, it is recommended to do the following:

The seam between the plates is cleaned, trying to remove the old putty as much as possible.
Before closing a hole in the ceiling, the working area is covered with a primer layer and dried well.
Fill the gap with putty, and glue the sickle tape.
Putty is again applied on top of the reinforcing material and also dried well.
The dried surface is ground, dust is removed and coated with a primer.

If cracks form on the ceiling without a gap between the plates, then it is recommended to glue the problem area with sickle tape, cover it with a thin layer of putty and cover with a primer.

Hole around the riser

A hole around the risers of communication systems is not formed so often, but you still need to know the solution to such a problem.

Seal holes in the ceiling in this case is performed as follows:

A small gap, up to 0.5 cm wide, can be filled with silicone sealant. This material is characterized by good plasticity, therefore, during the thermal expansion of pipes, there will be no obstacles.
In the presence of large holes, the work becomes somewhat more complicated. In this case, before sealing a hole in the ceiling, additional reinforcement is required, for example, welding electrodes. Further actions involve filling the hole with mounting foam in several layers. Excess hardened foam is cut off with a knife and sealed with putty. If the problem arose in a dry room, then you can take a gypsum-based material. Otherwise, it is recommended to use acrylic putty.

In conclusion, it can be noted that it is possible to seal a hole in the ceiling, regardless of the cause of the occurrence, with your own hands. Moreover, the work is available even for home master without experience, if he knows how to cover up holes in the ceiling.

It often happens that before painting a used car, we find a through hole formed due to corrosion. What can be done in this case, if you leave the topic of professional body repair and high costs. Is it possible to fix the hole myself, and if so, how to do it? All this will be discussed below.

ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!

Of course, the possibility of carrying out self-body repair is related to the level of damage to the car. For example, if a through hole is seen in only one place, and the body as a whole or its part is not completely rotten, you can proceed to self-elimination. In other words, if a partial problem is observed, and not a set of defects, it is 100% possible to do without specialists.

Note. In addition, do-it-yourself elimination of through holes is relevant only if they are not too large. Otherwise, you will have to order a professional service.

Filling holes in the body with putty

As a rule, most holes occur on the bottom of the car. And in this case everything around is thoroughly cleaned, auto cosmetics (rust converter) and many other sets are used. Degreasing and primer are also required.

The technology of direct application of putty, without the use of a patch, involves application from the back of the lining area. Thus, it will be possible to substantially achieve the maximum fixation of the composition. Can be used instead of lining as such metal mesh. These are even sold in the store, you can make them yourself, etc.

The putty must be evenly distributed over the surface, filling the entire space of the hole. After the solution has dried, the area is treated with auto-filler. Then, after drying, paint and put protective film.

This option for eliminating a through hole in the body is the simplest. Experts, however, do not recommend using it, since the putty will eventually begin to let in moisture and collapse. This method is most acceptable if restoration is urgently needed, and there are no other alternatives.

Algorithm for the process of eliminating a through hole by applying a patch with a soldering iron

Here's what to do:

To begin with, it is recommended to thoroughly clean the corrosive place from rust. You can use nozzles and a drill (also another set of tools).
A patch is cut from a piece of metal sheet. An option is to use a can of car chemicals, etc.

The patch should completely cover the hole on the element of the car skeleton.

A powerful soldering iron is being prepared, with which the patch is placed.

Now you need to tin the edges of the patch.

Particular attention is paid to the edges of the hole where the patch will be placed.

A piece of metal is soldered with a continuous seam.
It is checked by measuring whether the patch protrudes above the surface of the body with a bubble.

You can diagnose the protrusion using a flexible ruler.

The protrusion (if found) is sunk with gentle hammer blows.

After the patch is recessed, a small dip is bound to occur. It will need to be leveled using putty. We must not forget that the thickness of the putty layer should not exceed 2-3 mm. Otherwise, after drying, the layer will crack easily.

Before puttying, the surfaces are properly prepared: the rust is brushed off with a metal brush, and then the sanding is done.

It is better to use a sandpaper at 120. We must not forget that the matting area should be larger than the directly putty area.

An abrasive risk is applied to the surface. This is done so that the putty has something to hold on to.
Now it is necessary to process all zones after sanding with a degreaser.
Surfaces should be primed first. This is done no later than an hour after sanding, since the cleaned metal without paintwork quickly undergoes oxidation processes.

The first layer is better to take a phosphate primer. This type of primer is a 2-component composition, easily diluted with water.

Attention. It is forbidden to breed a phosphate primer in a metal container. The fact is that phosphate tends to interact with iron, and this is not good. It is better to use a glass or plastic container.

If you could not find a phosphate primer, an aerosol KSL primer in cans is also an option.

As soon as 10-15 minutes have elapsed after applying the first primer, it is necessary to proceed to surface treatment with acrylic. This type of soil is applied already in 2-3 layers. The interval between layers is maintained for about five minutes.

Note. Again, acrylic primer can successfully replace the composition of the AER spray. This is especially true if there is no compressor.

Acrylic dries completely within 3-4 hours. If it is possible to use INFR heating, the drying period can be significantly reduced.

It remains to putty the surface, then sand and prime.

The method of sealing a through hole with a patch is considered the most rational for a number of reasons.

Soldered patches last much longer than just fiberglass putty.
The patch gives a more reliable connection.
You can close holes of almost any size (except for too large, when only the service of specialists is relevant).
The simplicity of technology. Even a beginner can handle the job.

Video on how to close a through hole

Other troubleshooting

AT recent times it is possible to close the holes in other ways. One of them involves working with fiberglass.

Instruction:

The surface of the body is also cleaned and degreased, as in the two cases described above.
Overlays are cut out of fiberglass, the size of which should be 2 cm larger than the size of the hole.
The zone is pre-primed, the composition is given time to harden.
The overlay is applied to a completely dry surface.
Fiberglass overlays are fixed with the help of an adhesive-resin composition.

First, one overlay is glued, then the second, the third, and so on. Again, it is recommended to put a lining on the reverse side.

After the glue dries, the body surface is treated and painted.

As you can see, the holes on the car body caused by corrosion are easy to fix with your own hands. Visual examples can be seen in the video and photo.

Stretch ceiling - a unique finish, the cost of which is low, and the result pleases with its impeccability. The use of such coatings in new buildings is justified. Since it takes 2-3 years for shrinkage to more or less stop. During this period, cracks appear on painted, plasterboard ceilings. The hinge remains like new. But what if there is a hole in stretch ceiling? How to fix? Photos and instructions - further in our article.

How defects appear

At home, an unplanned hole appears quite unexpectedly from a shot cork of champagne or installing a baseboard. Well, if there are small children in the family, then it is unlikely that such a nuisance will be avoided. At least once, but it will definitely arise. At these moments, you should not panic, but it is better to remember what type or PVC) is installed, whether it is a warranty case or not, and evaluate the location of the hole.

Another source of trouble can be electricity. Wrong wiring is the cause of the burnout of the ceiling. Accommodation under tension structures heaters, unprotected light sources becomes the result of black spots and melting. These troubles can be avoided if you provide for the safe placement of electrical appliances, and entrust the wiring to a professional.

Warranty cases

Sometimes the owners forget that they entered into an agreement for the installation of stretch ceilings, and the obligations of the parties are spelled out in it. It often happens that it is a factory defect, poor-quality installation that causes holes in the stretch ceiling. Warranty cases where you should contact the contractor include:

Seam expansion. In such situations, you should contact the company that was involved in the installation. There is a poor-quality installation, or a defective canvas was used, incorrect cutting and hauling.
The formation of holes around the perimeter of the walls. This is the result of poor quality installation.

In such situations, a warranty hole appears in the stretch ceiling.

How to close up - the question is no longer yours, but the manufacturer's. You can safely apply for the elimination of such a marriage.

Non-warranty cases

This category includes all holes that have arisen through your fault. You can solve the problem radically and completely replace the canvas or be smart and correct the error that has appeared.

It is important to understand what material the structure is made of and what the scale of the disaster is.

fabric ceilings

It is easier to work with such canvases, but there are some peculiarities. And if a small hole appeared in the stretch ceiling - how to fix it with your own hands? Let's consider several options:

If the hole is small, you can sew up and carefully paint over the seam with a suitable color.
For large holes, a patch is applied. And, as in the first version, it is painted over. The patch is inserted inside and carefully glued with colorless glue. It is advisable to choose a fabric in the color of the canvas.
Application or sticker will not only hide an unplanned hole, but also transform the surface.

For such work, the dismantling of the canvas will be required.

And it is better to fix the edges of the hole with tape before repair. If you are not sure that you will be able to produce quality repair work, it is better to contact companies specializing in them. They will suggest how to solve the problem and carry out the repair of the coating at a professional level.

PVC ceilings - a hole next to the fastener strips

If such a hole has formed in the stretch ceiling, how to fix it? The question is easy enough to solve. If the hole is small and located at a distance of up to 150 mm from the mounting strips, then you can try to tighten the ceiling by removing the hole by the strip, fix it, cut off the excess. But this option is suitable if the canvas is not initially overstretched during installation:

Secure the cut edges with masking tape. This will prevent further spreading.
Remove the fastening strip from the side of the cut.
Heat the film with a hair dryer and gently stretch it so that the cut is removed.
Install the fixing bar back.

This is one of the most simple problems when a hole appeared in the stretch ceiling. How to fix it, we considered. But what if the hole appeared far from the wall?

PVC ceiling: hole away from the wall

In such options, it is possible to provide for the installation of a spot light device:

Fix the edges of the cut with molar tape.
Install the reinforcing ring under the additional element. It is installed using a special adhesive for film ceilings.
In the formed ring, make a technical hole for equipment, for example, for a spotlight.
Install equipment.

Rogue devices (non-working) can be installed.

If you decide to install a functioning one, you will have to partially remove the tension fabric in order to connect the electrical wiring. But thanks to this, an additional light source will appear, and this is also a plus.

PVC ceiling and applications

Is it possible to close a hole in a stretch ceiling in this way? Yes, this is one of interesting options. In addition to repair, it is also a way to transform the interior by adding zest.

A decorative patch is purchased - such that it can cover the incision. As a rule, they have a self-adhesive backing. The protective film is removed from it, and the application is carefully glued and smoothed. You can remove not all the protective film at once, but as the application is glued. This will help stick it more evenly without bending.

If the warranty is over

How can I fix a hole in a stretch ceiling in this case? If the seam has come apart, then a complete replacement of the film will help. But if the canvas lags behind along the perimeter of the bar, then you can try to eliminate this defect, but first determine what caused this:

Incorrect cutting, the canvas is overstretched. In this case, the repair will not help, you will have to order a new ceiling. But it will cost less, since only the canvas will change.
Poor quality If such a hole has formed in the stretch ceiling, how to fix it yourself? Bought new profile instead of the old one. The clamping guide is removed. The fabric is heated. Better suited for this heat gun. The ceiling is stretched and fixed with a new bar.

If you are not sure that you can determine the source of trouble and cope with the task, it is better to turn to professionals. They will be able to solve the problem qualitatively.

What defects cannot be fixed?

In some cases, repairing the canvas will not make sense. This is if the seam has parted and if a hole has formed more than 200 mm. In the second case, even installing a patch or application will not save, the tension hole will diverge further. Therefore, the replacement of the canvas can not be avoided. Well, if the seam has parted, then it will not work to glue it on its own, so a complete replacement of the canvas will be required. Since organizations involved in the installation of ceilings will not be engaged in gluing old paintings.

It is unpleasant when a hole appears in the stretch ceiling. How to close up a series of holes - we have already considered. But not all troubles can be overcome on your own, so you should listen to folk wisdom about the miser who pays twice. When ordering stretch ceilings, you need to pay attention to the reputation of the company; the materials she uses; warranty periods and more. In the future, this will reduce the risk of low-quality ceiling finishes in your home.

If, through your fault, a hole has appeared in the stretch ceiling, you can easily fix the problem by following this article. If you are not sure that you can handle and carry out the work with high quality, contact the company that did the installation for you.

So, we figured out how to fix a hole in a stretch ceiling.

Stretch ceilings - the most popular option for finishing the ceiling, used both in houses of modern construction, and in "Khrushchev" or "old fund". This finish allows you to hide bumps, cracks, unsuccessful painting and the consequences of leaks. Even new plasterboard ceilings do not give you confidence that your ceiling will be perfect in 2-3 years, because often the joints begin to crumble, and when the building “shrinks” after construction, cracks may appear.

Damage Features

Stretch ceiling avoids disappointment and remains flawless long years. True, a hole may appear on such a ceiling. The reasons for its appearance can be very different: a cork from champagne, unexpectedly "shot" for festive table, a toy thrown high by a child with a sharp angle (as well as darts, children's pistols and arrows), installing a lamp or curtains. Unfortunately, electrical wiring and electrical appliances can also cause damage to the stretch ceiling.

Sometimes it seems that a small hole will not do much harm, especially if it is not located in a visible place. Be careful: repair of even a small damage to the stretch ceiling is required, because over time, the fabric or PVC film will sag at the point of rupture, and the size of the hole will increase.

What to do? Of course, do not panic and remember that most often you can close the hole with your own hands. According to the reviews of the owners of the premises with stretch ceilings, almost every one of them faced a similar problem at least once.

So:

Evaluate whether the defect can be attributed to the warranty case. Poor installation, factory defects, seam gaps - all these points are usually spelled out in the contract that you concluded when installing the ceiling. If holes have formed along the perimeter of the walls in the ceiling sheet, then there is the use of defective material or poor-quality installation.

A discrepancy in the seams is a reason to file a claim with the contractor, because this is a sign of improper cutting and “tightening”. If your case is under warranty, provide the opportunity to eliminate the error to the manufacturer.

If several holes have formed in the ceiling, and they are located in different places, then the best solution would be to completely replace the stretch fabric.
If, nevertheless, a hole arose through your fault, then, first of all, decide which ceiling you will have to work with - from PVC material or fabric.
If you think that the edges of the hole may come apart, then secure them with tape.
Before any gluing of patches, it is necessary to degrease the area to be repaired. Do not use alcohol or solvents, they may damage the ceiling. It is best to use special products for the care of stretch ceilings or a solution of laundry soap.

So, you know the type of ceiling, decided on the complexity of the repair, adequately assessed the damage and are ready to start repairing

Canvas repair

As a result of careless use of an electrical installation tool, a stretch ceiling may be punctured. If you accidentally made a hole in the panel with a screwdriver or a tester, then you can repair such damage without inviting specialists. With a puncture, there is no need to dismantle the entire ceiling.

A small circle cut out of PVC film, similar in quality to your ceiling film, will be invisible from a distance of 2.5 meters. Therefore, feel free to seal the puncture with such a small circle or square, while using glue for PVC materials or vinyl wallpaper.

A wide range of adhesives is available in construction stores. therefore it is important to carefully read the attached instructions. However, all these tools have one common property One thing to keep in mind: all PVC adhesives set extremely quickly, as a result of which any delay in working with a patch can lead to a second (and more difficult) repair.

A stretch ceiling made of fabric is durable, but a puncture can also occur in it. As you know, such ceilings consist of a base (polyester canvas) and a shell. If only the shell is pierced, then the drop silicone sealant able to fix things. If the damage has touched the base, then the puncture must be sewn up with a thin thread (it is better to choose a synthetic thread of a suitable color).

From fabric

Repair fabric ceiling easier than PVC ceiling. A small hole or incision can simply be sewn up and painted. A large hole will require a patch. Important: we smear the patch with colorless glue (the ideal option is glue based on cyanoacrylate) and insert the holes inside.

Smooth out the fabric carefully. We glue the edges of the patch with special care, give time to dry and paint over with the desired color.

One of the “patch” options is a beautiful application(sticker), which can be purchased at special hardware stores. There are many options for such stickers - flowers, clouds, birds, so it will not only eliminate damage, but also decorate the interior. In some cases, to install a patch or application, the ceiling sheet must be dismantled and reinstalled. If you doubt the success of a do-it-yourself repair, you should invite professionals.

If the traces of repair are very noticeable or the applications hiding the gap are tired, it is possible to completely paint the stretch ceiling.

PVC

For a PVC ceiling, the location of the damage is important. A small hole no more than 1.5 cm from the fastening strips can be removed by pulling up the PVC material. This option is only suitable for "non-stretched" ceilings, allowing you to pull the hole up to the bar and secure the material. In order to prevent the material from tearing even more, secure the edges of the hole with masking tape.

If the "tightening" seems to be a difficult procedure, then the fastening fixing bar closest to the hole must be removed. Next, with a conventional hair dryer, we heat the surface of the PVC material and stretch it so that the holes are no longer visible. We install the mounting plate back.

To seal a hole that has formed far from the wall is already much more difficult. Experts recommend installing a point light device at the site of the defect. To do this, a reinforcing ring of a suitable size is installed under the lamp, fixing it with a special adhesive for PVC materials. Modern technologies allow you to install a lamp that turns on using the remote control, so wiring is not prerequisite. You can also install a false device, that is, it will not give light, but it will close the hole perfectly.

The next option is all kinds of decorative patches for PVC ceilings, which are made self-adhesive. One of the sides of such a patch is protected by a special film. If the application is large, then it is not recommended to remove the entire protective film at once, otherwise its edges may be bent.

Defects beyond repair

Unfortunately, incorrect cutting or overstretched fabric can lead to seam separation. Repair will not help here, you will have to install a new canvas. True, replacing the panel will be much cheaper without acquiring new fasteners and fixing strips. You need to contact the company that installed your ceilings for help.

A large hole from exposure to water or fire will also lead to the replacement of the tensioner, do not try to fix damage on a large scale yourself. Do not forget that incorrectly or carelessly installed fastening strips can cause gaps, gaps between walls and ceilings.

Breaks from the water

Unfortunately, cases of flooding of our apartments by neighbors from above are not so rare. A PVC stretch ceiling is able to withstand a large mass of water, while the stretch fabric turns into an impenetrable bag. PVC ceiling is waterproof and stretches beautifully, so in most cases it is able to save your interior. To extract the water, you will have to make two neat punctures - one in the very center of the giant drop, and the other where there is no water. The easiest way to make a puncture is with an awl.

Most likely, after such a nuisance, the tension fabric will have to be replaced. However, if there was little water, the affected elastic material can be restored to good condition.

The fabric ceiling can also suffer from water.- its large volumes will simply tear it at the attachment points, since it does not stretch. In addition, after the “water attack” on the fabric ceiling, most likely, ugly stains will remain, which, however, can be corrected by regular painting.

In order for the stretch ceiling to serve you for many years, ordinary household neatness is enough.

Choosing how to decorate the ceiling, the owner looks at the aesthetics and practical characteristics of the panels. Fabric stretch worse, but stronger, film can keep water from the ceiling, but do not differ in resistance to mechanical stress. For one reason or another, you can tear a canvas from any material, and if the hole is small, then there is no reason to panic. We will tell you how to fix a hole in a stretch ceiling with your own hands.

Holes in the canvas are not uncommon, especially if there are small children in the house:

Small hole or cut appear due to ball games, launching airplanes. The defect may be formed due to careless handling of sharp objects during the repair period, when installing lighting fixtures. Often the film is cut through the corners of tall cabinets.
Big hole in the ceiling- a consequence of an unsuccessful attempt to take out furniture, games, blows with sharp objects (ski poles, cue).

To repair a defect of a small size, you do not have to spend a lot of time and effort. Another thing is when the hole spreads, it all depends on the location of the defect:

Option with a divergence of the seams of the fabric it is also considered maintainable, but here you have to turn to specialists, you won’t be able to fix the situation yourself. The seam is coming apart due to Bad quality factory gluing or too much pressure on the web, for example, when flooding from above.
Holes in the baguette area, wall panel appear due to the departure of the fixing profile.

It happens that the ceiling sags, which is why a crack appears in the canvas.

Reasons for sagging:

violation of the technology of fastening the harpoon to the canvas;
fragility of mounting the panel on the baguette;
looseness wall panels- here the design departs along with the profiles.

Depending on the defect of the stretch ceiling, the repair of the hole will be simple or complex, it will require the attention of the master or is done by hand. But first you need to raise the act of acceptance of work, and clarify the effect of the warranty period. In this case, the repair will cost quickly and free of charge.

Warranty cases

These include:

seam divergence, if it's a bad quality sticker. The fabric installer must replace the fabric/film free of charge.
Release of fasteners. It happens due to non-compliance with the fastening step, when installing profiles in weak walls (GKL) without additional reinforcement, or low-quality fasteners were taken.
Poorly soldered harpoon insufficient dressing of the canvas in a baguette - also warranty cases.

If on-site repair is not possible, the master takes the coating for restoration or stretches a new canvas. The warranty period for canvases is up to 12 years, for fasteners up to 3 years.

Important! Before considering options on how to seal a hole in a stretch ceiling, be sure to review the contract. And even if the repair is not a warranty case, you should notify the company - any intervention in the design can nullify the warranty period.

Non-warranty cases

These include:

Rupture or divergence of the seam under the weight of water, exfoliated plaster. Repairs will have to be done at your own expense.

Important! When arranging a tension fabric, the company can take on the whole range of works: cleaning the base, fixing. Exfoliated plaster is a consequence of poor cleaning of the ceiling. In the case when the procedure was carried out by the services of masters, the repair is carried out under warranty, it is only necessary to prove the occurrence of a warranty case.

All other defects that have appeared due to careless handling of toys, sharp objects, etc., are non-warranty and are corrected by one's own hands.

After the work is completed by the masters, all interventions in the ceiling sheet are considered unauthorized and the warranty period is canceled. Intervention is considered: installation of fixtures, complete or partial dismantling, replacement of baguettes.

When is ceiling replacement required?

Complete dismantling required:

with the formation of large holes, cuts;
the appearance of a defect in an area where it is not possible to decorate with lamps, fill in a baguette.

The option with a seam divergence is considered separately in each individual case: with even gusts, sometimes the master can glue the canvas anew.

The technology of sealing holes in stretch ceilings

Step-by-step instructions for repairing tension panels will come in handy for people who want to cope with the work on their own. There are several repair options: glue, sew, pull or decorate the hole. It all depends on how serious the defect is and where it is located.

Tools and materials for termination

The master will need the following set:

solid base (ladder, table);
roller with a handle;
cuvette for paint;
measuring device (meter, ruler);
spatula with rounded corners;
needle and thread (for fabric ceilings);
scissors;
hair dryer (for film ceilings);
rubber or cyanoacrylate glue;
dye;
a piece of matter;
thick cord for attaching the harpoon.

Personal protective equipment will not interfere. Cloth gloves are necessary when working with PVC film, otherwise fingerprints will remain on the heated material.

Step-by-step instruction

Let's start the analysis with the fact that a small hole appeared in the stretch ceiling, what to do:

First measure the distance from the defect to the wall. If the hole in the stretch ceiling is no further than 5 cm, the web is sufficient. To do this, the harpoon is carefully released to the damage zone, then the free web is cut off to the hole, attach a cord to the edge with wrapping the material around the cord, glue it and you can tuck the homemade harpoon into a baguette. And in order for the alteration zone to stretch better, warm the film with a hairdryer.
If you get a big hole in the stretch ceiling, how to fix it yourself? There are several options:

install a ventilation grate if the dimensions do not exceed the grate and power wires can be connected;
put an additional lamp, under the same conditions.

Advice! To mask a hole with a lamp or a ventilation grill, you need to buy a thermal ring or a thermal square. The element is glued on top of the film, the rest of the material is cut out inside, wires are connected, then the grille or lamp is fixed.

Film canvases cannot be sewn up, the material will instantly spread under your hands. It is also not recommended to glue PVC sheets, you can only fasten the edges of the hole with a piece of adhesive tape so that the hole does not spread further. And then do the repair work.

How to fix a hole in a fabric stretch ceiling

If the cut or tear is very small, they can be sewn up. Nylon thin threads and a sharp needle will come in handy. It is better to choose the threads to match the material, the work is carried out carefully so as not to break through the hole even more. When darning in the corners, the defect is almost invisible, but in the center it will be obvious. Therefore, after the completion of the darning, the ceilings are covered with a water-based emulsion. So you can hide the consequences of the repair and give the coating a smooth look.

How to fix a hole in a fabric stretch ceiling if it is large? Put on a patch. For this, a piece of matter from which the ceiling is made is useful. Usually, the craftsmen cut the edge before starting work, such a piece is enough to renew the coating. There are no scraps left - a material of the same tone with a fabric ceiling will do.

Cut out the patch according to the size of the hole with an allowance for gluing. Glue with cyanoacrylate glue (it will set faster) on the reverse side. Very great care is required when placing the patch, so as not to break through the tear even more. Only the edges of the patch are smeared with glue, then the piece of fabric is carefully straightened and applied. Once the work is completed, you can decorate the ceiling with a water-based emulsion.

Advice! Do not be afraid to paint fabric ceilings. A high-quality canvas can withstand up to 5-6 staining cycles.

How to decorate a hole in the ceiling

If defects appear, it is not necessary to pull or sew up the material. In some cases, decor in the form of stickers is suitable. They are sold in departments of hardware stores. This sticker on the hole has different sizes, shapes. To make the decor appropriate, there should be several stickers - seal the hole and place the elements in other parts of the space, so a new style of the room will appear.

The area near the lighting fixture is even easier to decorate - a wide platform, polyurethane stucco molding, curly elements are suitable. They look good both on PVC films and on fabric sheets, they can be painted to match the ceiling or made contrasting.

Having figured out what and how to make repairs, whether it is possible to close a hole in a stretch ceiling, it is easy to cope with the work. But if the defect is large, you should entrust the matter to specialists. In this case, the owner will receive a guaranteed high result, and the price of the work will be much lower than a complete replacement of the panel.