What to make a home fountain. How to make an indoor fountain at home with your own hands? Master class desktop waterfall, do-it-yourself decorative fountain

Don't let the initial costs scare you. I have found from personal experience that ABSOLUTELY ALL ways of home business without initial costs do not bring the desired income and satisfaction from the (sometimes just HUGE) work done. Therefore, I suggest you do a very interesting job. The essence of the idea is simple: the production of decorative indoor fountains. At low cost, amazing results are obtained.

The system of any decorative indoor fountain is a cycle in which water rises up with the help of a pump and then flows down the stone into a container. Thus, we are talking about a closed system in which the used water is gradually renewed, since the initial supply of water is no longer enough by a certain time.

The pump is usually powered by a set of batteries or a power supply or both. Usually, for decorative indoor fountains, pumps powered by 3 to 9 volts are used. The higher the power, the greater the power of the pump, which allows you to lift more water up, and this, in turn, affects the location of the pipes through which the water flows. You can make a very tricky labyrinth of tubes, from which water will flow out in different directions and with different strengths and, believe me, it looks very, very beautiful!

Now let's talk about the design

The basis of any decorative room fountain can be any. While shopping, pay attention to all kinds of bowls with lids. Your fountain will depend on the chosen diameter of the bowl. The lid should either fit over the bowl or be very tight to the bowl so that it is difficult to tear off. But even if the lid doesn't fit very snugly on the bowl, you can drop glue in three or four places and the problem is solved.

Usually, the lid is made first, so to speak, the whole appearance your fountain. Depending on your idea, a hole is drilled in a certain place on the lid and a tube is inserted into it. At the beginning, it is desirable that it reaches the bottom of the bowl from below, and from above it is 5-10 centimeters higher than the calculated size of the fountain. Even if you don’t need these tolerances, you will always have time to cut off unnecessary ends, but it’s better to have them just in case. In the role of tubes, any kind of tubes, cambric and pipes are suitable. And it doesn’t matter what they are made of: let it be aluminum tubes or flexible PVC tubes, for example, from droppers.

Next, a base is made around the tube to create an appearance. Most often, a mixture of cement and pebbles is used. With cement, everything is clear, but I’ll tell you about the pebbles separately. Wherever you are (in the city, in the country, in the forest, at the sea, etc.), always pay attention to the pebbles. The more non-standard and bizarre the shape, the more unexpected its color, the better! And in general, try to notice all sorts of non-standard things (pebbles, twigs, roots, etc.) in order to use all these materials for the production of fountains in the future. When creating the base, simply throw cement on the lid and, while it has not hardened, sprinkle pebbles into it, immediately forming the landscape of the future fountain. Don't forget that the water needs to get inside the bowl and flow through the landscape. Therefore, try to make some kind of depression at the bottom of your landscape so that water collects there and immediately drill a hole there (but a small one, otherwise the water will immediately flow into the bowl. And it is much better when the water remains in the depression for a short time. It turns out a small lake) . If you do not get along with cement, then you can use all kinds of adhesives, sealants, polymer compounds, epoxy resins. Our task is to create a landscape from natural material, fastening it together and with the base. The fastening material must be moisture resistant so that the artistic composition does not fall apart.

You can also use various hi-tech tricks. Forged landscapes, bronze, metal, plastic or glass.

You can produce complex textures and geometric patterns using a 3D printer. Then your fountains will have no competition at all.

Video: 3D printed tabletop fountain

If you do not consider yourself an unrecognized artist or sculptor, it does not matter. Sometimes a masterpiece is obtained from just a pile of pebbles. Add absolutely any materials (usually they are just glued to the landscape), but do not forget that water is a very patient cutter. Therefore, it is desirable to use materials that do not decompose with water. Otherwise it will bad smell rotten water. But even with organic materials there are very interesting cases. For example, when I wanted to plant a real swamp moss on the fountain, then quite unexpectedly it began to become covered with white mold. But the most interesting thing is that there was no smell! The mold itself is a penicillin, and most likely it even helped filter the water. But it turned out very nice. The fountain has turned into a real living organism that does not age, because. swamp moss can live for centuries without growing in size.

After external design You just have to connect the pump to the supply tube and connect it to power. ALL!

After you try to make 3-4 fountains, try adding light to the landscape elements. I recommend using LEDs. First, you can choose the colors of the LEDs you want to highlight some specific parts of your landscape. Secondly, at the moment LEDs are sold with different light power, flashing, with fading pulsation, etc., which will also help you a lot when decorating the landscape. Thirdly, they are almost eternal, do not burn out and are not afraid of contact with water.

Dame one more smart advice. It is desirable to add a pair of relay contacts to the receiving container at a certain level (it is set experimentally) so that the water closes them and when the water level drops below the specified rate, the electrical circuit breaks so as not to drive the pump without water. But here there are two options. The first and easiest is to turn off the power to the pump.

But, as practice has shown, very few people read the instructions for using a decorative indoor fountain, which says that when the fountain stops working, you first need to add water. Therefore, it was necessary to improve the fountain a little and add a circuit to it, which, when the contacts are opened, lights up a flashing “Add water” sign below and emits an intermittent low signal. At the same time, safety precautions are observed, since the power supply of the pump and the circuit ranges from 3 to 12 volts and will not affect the touch of water with your hands.

That's all! Then turn on your imagination and create! For example, when I made a lot of landscape-type fountains, I started making fountains in the form of water mills, adding various moving figures to them. It turns out great!

Video - how to quickly and easily make a fountain for your home

The essence of business

All this is usually sold in the city market, or through social media. There is always a crowd in the market near my trading place. Fountains typically sell for between $50 and $150. But some copies left me and at a price of $ 300.

Some clients themselves later approached me and asked me to make a custom-made fountain, taking into account their personal wishes. Naturally, the price in this case was automatically increased by 50%. You can also walk around the offices and offer them decorative fountains. A lot of people are willing to take it. Only it is necessary to make fountains for offices a little more massive and larger in size. For example, for one office, I made a fountain 150 cm high, and it occupied a square 100 × 100 cm wide.

The profit arithmetic here is very simple, so you yourself can calculate the profit at the expense. If a copy is not sold for a long time, then I lower the price on it and they immediately buy it.

Now many have a desire to have (especially in summer) a small fountain that would make the atmosphere more exotic. But many are sure that this idea is beyond their means. At home, you can try to realize this dream. Homemade can be done in a few hours, even if you have never created such things.

Such products are divided into indoor (decorative) and yard, arranged on summer cottages or in the courtyards of multi-storey buildings (if they do not interfere with garages, etc.). There are many different designs of home fountains. Consider how the opportunity to make at least a small one with your own hands indoor fountain chik. To begin with, we will think over the future design according to the following parameters:

1. Desired sizes.
2. The form.
3. The number of cascades in your fountain.
4. Proper design of the closed water system of the product, otherwise the fountain will not work normally.

So you have passed the first stage, and you have a drawing of your fountain on paper. Now comes the next stage: you need to prepare materials and parts for the assembly you invented. Here is a rough list:

1. Small. If you are planning to make a desktop version, then you can use an aquarium pump-pump.
2. Hermetically sealed container made of metal or plastic. For these purposes, you can adapt any dishes available in the house (vase, plastic bucket, basin).
3. For decoration, you can use pellets, shells, decorative colored glass, etc.
4. Electric cords, sockets for connecting the pump.

Self-made fountain at home

The assembly begins with the installation of the pump on the bottom (bottom) of the container you have chosen. To do this, you can use synthetic adhesives or suction cups (if an aquarium pump is used, they are included in its kit). The rise of water to the upper level is carried out using a tube (plastic, silicone). We put it on the outlet of the pump and fix it strictly vertically. Further, in order to mask the pump and isolate it from the external environment, it is necessary to close the equipment with a home-made or purchased, suitable-sized frame. If you are going to make it yourself, then do not forget to prepare the materials and tools you need for this.

if you have plastic box with dimensions suitable for the pump, then, by cutting ventilation holes in it, use it as a casing. In extreme cases, you can shove the pump under a layer of colored pebbles. Next, you need to turn on your imagination, since the final result depends on it. We take any tank we like (a beautiful mug, a large sink, a plate, etc.)

It must be installed on some elevation.

This can be achieved by creating a slide of stones with your own hands, on which we mount our decorative tank with epoxy glue, into which a tube is inserted from the output end of the pump.

If there are no stones, then you can make cubes from foam or use ready-made plastic ones. To do this, we drill a hole in the vessel we have chosen according to the diameter of the tube, which is inserted into the tank (into its internal cavity), by 6-12 mm. We seal the hole and fix all the elements with our own hands, using waterproof glue and sealants.

Every year, millions of people spend huge amounts of money to visit exotic places on the planet. You can recreate the natural beauty in miniature by making a decorative indoor fountain with your own hands. The lively murmur of water has a beneficial effect on the emotional state of a person. Plus, you can't take your eyes off her.

The design gives the room not only a luxurious look, but also moisturizes the air in the hot season. To create a decorative indoor fountain with your own hands, it is not necessary to purchase expensive installations. The main thing is to be patient, turn on the imagination, pick up the tools and work wonders. First, let's look inside the structure to understand how it works. Then we will get acquainted with the types of indoor fountains. And finally, consider the step-by-step instructions for creating a natural miniature for the home.

The fountain is not only an element of decor. Since it wonderfully humidifies the air, it should not be installed near wooden furniture.

Why does water flow

"All rivers flow into the sea, but it does not overflow." So it is said in the most ancient book of mankind. We see confirmation of these words every day when snow or rain falls from the sky to the ground. The Great Designer launched the water cycle in nature. Imitating him experienced craftsmen created with their own hands a decorative indoor fountain that pleases the heart all year round. How does this system work?

The design is based on a unique water cycle in a closed system. They start it with the help of a connected to the power supply. It lifts the liquid up, after which it gracefully flows into the storage bowl.

There are decorative fountains in which several identical containers are used. They are built at different heights, connected by tubes. Pouring liquid into the vessel, which is located at the top, the system starts. Usual physics plus creativity and golden hands. The result is an exotic corner with a quiet murmur of water, which calms the nerves.

How to create a decorative indoor fountain with your own hands: step by step instructions

Before getting down to business, you need to think about the size and place where the structure will be installed. For example, in a small room a huge fountain is inappropriate to place. And, conversely, in a spacious room, a miniature structure may go unnoticed. Decorative fountain set on the floor, wall or table. Much depends on the overall design of the room and the number of household members.

Depending on the movement of water, fountains are:

1. Cascading - liquid falls down decorative steps or ledges.
2. Closed - water moves in flasks or flat containers attached to the wall.
3. Gushing - the jet is directed upwards, after which it falls into a miniature pool.

There are backlit options in the form of wall paintings that create a unique setting in the room.

When choosing a place for the structure, small children and pets should be considered. The main thing is that the building does not interfere with anyone.

But how to make a fountain at home with your own hands to fill it with exquisite exoticism.

Of course, you first need to understand the principle of the structure, and then collect the necessary items:

• suitable container;
• aquarium pump;
• flexible hose;
• waterproof glue;
• decorative elements (expanded clay, shells of various sizes, colored soil, wood, ceramic products);
• backlight (optional).

A vessel of any shape is suitable as the main bowl. The main thing is that water does not flow out of it. The upper part of the pump for a small fountain is equipped with a sprinkler. Since the dimensions of the structure are very small, the tip does not need to be worn. Otherwise, water will flood the nearby territory of the room.

It is quite possible to construct a miniature pump on your own, since the unit has a relatively low power.

Let's start the creative process

Those "who despise the day of humble beginnings" never succeed. Therefore, by collecting necessary tools and materials for construction, the wise guys get down to business.

Consider the traditional master class for creating an indoor fountain with your own hands at home:

1. A piece of about 10 cm is cut off from a suitable hose (you can use an aquarium). Its diameter should match the pump tip.
2. Attach the pump to the bottom of the tank with suction cups and connect it to the tube.
3. The resulting space is filled with expanded clay or stones, leading a tube between them.
4. To give the fountain a presentable look, all elements of the device are carefully masked with all kinds of shells, pebbles or glass.
5. Depending on the preferences and the interior of the premises, the design of the structure is carried out using various objects.

Stylish exotic in the interior of the bedroom

A small table fountain can be built from a flower pot with a diameter of about 25 cm.

For work you will need:

• durable container;
• pump;
• translucent balls or pebbles;
• aquarium plants;
• paints for painting on ceramics or glass.

Used for the foundation of the fountain. To give the design a stylish look, the container is painted with special waterproof paints. To circulate the liquid, a pump is installed, a hole is made and the tube is brought up.

The bottom of the fountain is decorated with decorative balls, shells or pebbles. After filling the system with water, aquarium plants are placed inside. They give the design an exotic look and originality. simple circuit creating a design opens wide opportunities for beginners.

The brook murmurs in the fountain and without a pump

Perhaps only a few have seen natural geysers in all their glory. There, as you know, there are no pumps, and there is no electricity. But such a release of water causes unprecedented admiration. Of course, at home it is impossible to create such a phenomenon without electricity. However, there is a way out!

For the construction of a miniature fountain without a pump, use:

• several containers;
• thin tubes;
• connecting adapters;
• sealant (if the containers are made of plastic);
• decor elements.

First of all, a small hole is drilled at the bottom of each bowl. Thin tubes are pulled through them, after which they are sealed with cold welding. The procedure will protect the system from fluid loss.

We all rejoice at the arrival of summer, but when the sun begins to bake strongly, we want coolness. Therefore, many tend to spend more time near the fountains, which will not only freshen the air, but also cheer you up with the sound of falling water. But it is not necessary to go to the square to admire this action. Each person, regardless of whether he lives in an ordinary city apartment or in a private house, can make his own decorative fountain.

Pros and cons of creating

A decorative fountain is primarily an element designed to decorate the surrounding space. It has several key advantages:

But artificial fountains have certain disadvantages:

• The need for special care and periodic monitoring. This structure must be cleaned regularly to prevent debris from clogging the pump. It is also necessary to monitor the health of the equipment and promptly eliminate the problems that arise.
• Considering that the pump requires mains electricity, running the fountain will incur certain costs, which can be especially high if the installation is to be operated for a long time.

Types of structures

Decorative fountains can differ from each other in various ways. For example, according to the type of accommodation, it is customary to classify them into home and street. The former are designed to decorate rooms, while the latter are used in open spaces, where they act as an integral element of landscape design.

According to the type of construction, fountains can be divided into several types:

Depending on the nature of the movement of the water flow, fountains can be divided into the following types:

It is also customary to highlight annular a fountain in which an annular-shaped pipe is provided, and holes are located in it at the same distance from each other. At the moment water is supplied through them, a stream appears that resembles a ring.

An interesting variation is the installation in the form of a hemisphere or hemisphere. In its composition, it has several parallel disk nozzles connected in a special way. At the moment of supplying water under pressure, the jet acquires a spherical shape, which gives the entire structure a very unusual and spectacular appearance.

Shapes and sizes

Although the fountain can be of any size and shape, when choosing them, it is recommended to be guided by common sense and do not forget that it will be somewhat more difficult to care for the installation of a more intricate shape and large dimensions.

The bowl of the fountain can have a symmetrical or non-standard asymmetrical shape. For example, it can be made in the form of an oval, square, circle, triangle, as well as any other geometric shapes, including those that follow the contours of the silhouette of an animal or a person.

Also, fountains can be complex multi-level or made of several interconnected containers. In this case, each of these elements can be equipped with its own nozzle, being an integral part of a more complex installation.

Stylistic design

Fountains used for decorative purposes can be made in a wide variety of styles. The belonging of the structure to one direction or another depends on various factors - appearance, shape and size, material of manufacture.

There are several design options applicable to decorative fountains:

Installation location

To decorative fountain was able to successfully cope with his role, it is necessary to correctly approach the place of his placement.

Prepare the site in advance so that you can approach the fountain or stay close to it. Make sure that the structure is not covered by other elements of landscape design.

DIY decorative fountain

It is not necessary to pay money to the master for the manufacture of the original decorative fountain. Any owner can cope with this task on their own.

Materials and tools

And first of all, you need to prepare the tools, materials and fixtures necessary for work:

• container that you will use as a bowl. It could be old barrel or bath. The main thing is that the product is strong enough without damage to withstand the volume of water;
• a pipe or a sufficiently strong and dense hose for water supply;
• pumping unit;
• materials for waterproofing;
• filter;
• nozzle;
• shovel.

Manufacturing process

After you have prepared everything you need, you can proceed to the manufacture of a decorative fountain:

The fountain you made will last longer if you regularly check the condition of the devices and promptly eliminate the malfunctions that arise, as well as clean the bowl of debris that gets into it.

A decorative fountain can become one of the main elements of your site and change its design for the better. You just need to get it right to make it. With a little imagination and using unnecessary materials, you can surely create a creation with your own hands that will look no worse than those made. professional craftsmen products.

doing landscaping household territories, some owners at some point come to the understanding that there is not enough fountain on the site. You should not give up this idea if you have everything planned out for a long time and there is no extra space left. After all, it does not have to be a large structure. Even in small areas, you can find a place to arrange a compact decorative fountain there, which will give you coolness and become a great relaxation area.

If you decide to create it yourself, then you need to thoroughly prepare for this work. And first of all, you must understand what kind of installation this installation should have, what material it should be made of and how water should flow in it. These and many other factors will determine whether you are satisfied with the end result.

If for the first time you have to make your own fountain in the country, then you should not build an installation of a complex configuration. This will not only require more time, money and effort from you to create it, but will also create certain difficulties for you in the future during your care. It is best to build a small standard-shaped fountain, which can be made from the most common materials and will be no more difficult to care for than any other object on your site.

Even if the pond on your site is small, it can contribute good contribution to beautify your area. And if you decide to build a fountain with your own hands, it will be interesting. It will not just be a place of leisure, but you will also receive a mountain of praise from friends, acquaintances and neighbors.

However, not everyone wants to take on such an idea, because they think that the construction of such a hydraulic device is very expensive and time-consuming, and also requires the intervention of a specialist. If you want to know how to make a fountain at home, then we want to please you that anyone can afford to build a fountain with their own hands at home, you just need to know all the points of design and construction. In this article we will look at how to make a fountain.

Fountain types

Due to the type of construction, products are divided into two types:

1. Open fountain. As a rule, in such buildings, water is supplied to the nozzle. The jet is formed due to the fact that there are differences in water levels. Here you need to monitor the water level, and the water quickly becomes dirty. In order to create such a pressure, you need to raise the container by a meter from the nozzle.
2. Pump fountain. This is the most common design option. Here the pump is placed on the bottom, which creates a constant cycle of water. For structures of this type, the pressure is quite strong and visually looks more beautiful.

tiered fountain

According to the type of pumps, fountains are divided into submersible and stationary.

1. Submersible pump. It is placed at the bottom of the pond. With the help of a pipeline, water rises to the surface, and the nozzle creates a certain form of flow. In this embodiment, water seems to erupt from the earth.
2. A stationary fountain is usually built from stones in the form of a figure, the shape of which can be any to your taste. Such structures are installed in a park or square, as they are a kind of art.

Ideas for a fountain (video)

Where to install the fountain

When choosing the optimal place for construction, it is important to take into account such a factor as the slope of the earth. If the surface on the site is uneven, then it is better to install the structure at the bottom. Thanks to this, it will be easier to adjust the volume of groundwater, and the oxygen saturation of the air will also increase.

Install the fountain where it will be convenient to admire it

It is not advised to build a fountain:

1. Near the house, as with a strong wind, water will fall on the house itself.
2. In an area with direct sunlight, which will contribute to the rapid flowering of water.
3. Under a tree, as fallen leaves or overgrown roots can ruin the product.

It is necessary to place the fountain so that it does not interfere with moving around the yard, but on the other hand, so that it can be clearly seen from different sides. We advise you to locate it near the place of leisure.

The smallest distance that should be between the structure itself and green spaces is 0.5 m. Thus, the plants will be protected from a large number moisture. The same principle is relevant for furniture near a water feature. The most optimal location of the structure is a place in the shade and without wind, near water and an electrical network. So I will save your efforts and material costs.

After we have decided where the fountain will be, you can proceed to its design or what will be the shape and depth of the building

Construction materials

To save money and power costs, it is possible to build a pond with a pump placed in it.

Materials for building a fountain:

1. Capacity
2. Pump
3. water insulator
4. Shovel
5. Stone of various sizes
6. Decor elements

How to choose and install a container

In the case of a small fountain, an ordinary small basin can serve as a reservoir.

For a larger option, you can use a bath or a pit dug with your own hands. When using a bath, you need to dig a hole so that its edges are below ground level. First, all holes are closed in the container, then it descends into the pit, where it needs to be strengthened with stones and earth.

If you want to dig your tank, use a film for this. It, in turn, should be dense and of high quality. In a dug hole, the film is pressed against stones. Also, stones are lined to the bottom. They should not be sharp, as this may damage the film. They need to be evenly distributed throughout the bottom.

How to choose a pump

To build a fountain, it is not necessary to buy expensive materials, since you can use the elements used in the household. But you don’t need to save money on buying a pump, since the quality of the pump determines how long it will work without problems, and the more beautiful the end result will be.

The best choice for construction is to use submersible pump. But if you have a large or cascading fountain, installation of a surface pump is welcome.

The main indicator when buying a pump is its power. If your fountain has a small water pressure, then you do not need to buy a powerful pump. It is important to know that the power corresponds to the diameter of the pipe, and the pressure must be strong, otherwise it will be the result of an unsuccessful fountain.

The erection of the fountain

The construction of the fountain consists of five stages:

1. Digging a pit
2. Trench reinforcement
3. Fixing the tank or installing the film
4. Pump installation
5. Fountain decor

Now consider some options for building a fountain with your own hands.

Examples of building fountains

With the use of a tire

For this we will need

1. Old used tire, for example, from under a tractor
2. Cement, water, gravel and sand
3. concrete mixing tool
4. Film
5. Level
6. Stones of various sizes
7. Mastic or silicone
8. Pump

Fountain made of tires lined with stone

Sequencing:

1. Preparing a concrete solution.
2. Pour the solution onto the bottom 10 cm high and level using a level.
3. After the solution dries, put the tire on the bottom, after cutting off the sidewall on one side.
4. Using mastic or silicone, glue the tire to the base.
5. Concrete is poured along the edge of the tire, thereby strengthening the structure.
6. We put the pump in the center of the tire.
7. We decorate the fountain. With the use of a tire

Using film

For this type of fountain you will need:

1. Thick film
2. Shovel
3. Sand
4. Pump
5. Stones of different sizes

Fountain in a film pond

Sequencing:

• First, you need to dig a pit, remove everything superfluous from the pit, for example, stones and ram the bottom.
• Next, you need to fill the pit with sand.
• The next thing to do is to lay the film. We lay it so that the edge goes beyond the hole. Then we press the film with stones along the contour of the pond.
• Then we install the pump, depending on its type and instructions.
• We decorate an almost built work of art according to your taste.
• Fill the pond with water.

Using an old bath

For this case, you need to have in stock:

1. Shovel
2. stones
3. Pump
4. Bath
5. Insulating tape
6. Metal shears
7. Metal sheet
8. Drill

Fountain from old bath

Sequencing:

1. We tear out a hole according to the size of the bath.
2. We lower the bath into the pit and clog all the holes
3. From a sheet of metal, you need to cut wide strips and lay them around the perimeter of the bath, pressing down with stones.
4. Decorative gravel can be placed in the bath itself.
5. Installing the pumping system.
6. It is possible to set the backlight, and change the color of the water with the help of blue. Thanks to this, the bath will not be noticeable.
7. We decorate our design.

Using a plastic bottle

For such, if I may say so, a fountain, you need to have available:

1. Plastic bottle
2. Carnation
3. Insulating tape
4. garden hose

Practicality in everything!

Sequencing:

1. Remove all stickers from the bottle.
2. We punch holes in the bottle with a hot nail.
3. We install the hose in the bottle and tightly wrap it with tape.
4. We place our structure in the planned place and turn on the pressure.

This mini fountain is suitable for watering the garden and garden.

home decorative fountain

For this we need:

1. Flower pot
2. Glass paint
3. water pump
4. contours
5. aquarium decoration

Flower Pot Fountain

Sequencing:

1. We paint the pot with paints.
2. Make a small hole in the bottom of the pot.
3. We mount the pump under the pot stand.
4. We pass the tube through the hole made.
5. We put pebbles on the bottom.
6. We make decoration.
7. We fill the container with water.

Decor

If you decorate your fountain, it will further emphasize how unique it is. Near the pond you can put natural stones, you can even different colors, expose houseplants, put various figures of toys or animals, etc.

Design lighting can amaze your guests with its originality. This is done using special equipment. Lamps are placed along the perimeter of the structure, and lighting is installed at the bottom.

Plants and decor for the fountain

Aquatic plants can be placed at the bottom of the reservoir, and shrubs can be planted around it.

Fountain Care

After you make a fountain at home, it will, of course, need to be well looked after. In order to maintain order, and the water was clear, and the building had a pleasant appearance, it is important to constantly clean the tank. Using special tools, you can remove leaves and similar things from the pond that can spoil the water, as well as damage the equipment.

When the summer season is over, you will need to drain the water from the reservoir, remove the equipment into the room, and cover the rest with oilcloth to protect it from dirt.

Making a fountain with your own hands in a summer cottage or in your apartment is not so difficult and does not require large material expenses. Before erecting a structure, you need to find out what its shape, size and location will be. You can place it anywhere - in your garden or near the gazebo. Subsequently, the fountain needs to be well looked after - control the cleanliness and water level, as well as remove fallen leaves.

Such structures are often installed in suburban areas. The fountain can decorate any free area or become its oasis. If you connect your imagination and use various decorative elements, the fountain will look even better and more original.

How to mount a fountain in your garden (video)