How to remove old ceramic tiles. Removing tiles in the bathroom. How to remove old tiles from walls

To date, the preference for unusual and worthy decorative finishes downright huge: plastic panels, various wallpapers, facing tiles and so on. With all that, you first need to get rid of the old tiles. How to remove the old tiles from the wall so that everything ends quickly and with minimal effort - we will analyze this in this publication.

Tools needed for the job

Removal procedure tiles not so difficult if you work very carefully and use the necessary or, so to speak, auxiliary set of tools and personal protective equipment. You can settle everything with the help of a set of tools and things such as:

• Perforator, which has a nozzle or chisel with a hammer;
• Spatula (small and strong recommended);
• Films and rags;
• Protective glasses;
• Work gloves;
• Respirator;
• Drill and additional drills to it.

All of the above tool names are extremely important to have. Since this will affect the quality and speed of work, including worker safety.

Dismantling technology

When removing an old tile, they are first taken to prepare a workplace where it would be appropriate and most important to work effectively. If it becomes necessary to remove the old tiles from the walls, then we cover the floor with plastic wrap, cardboard or thick cloth in order to make it easy to clean up the debris that appears during work throughout the room, or there is a need to save the floor covering.

It is imperative to put an old blanket or something soft on the sink and toilet bowl, thereby protecting them from the possibility of falling into the fragments of the old tile (do not forget that ceramics are very fragile). Following the completion of the work, you will only need to carefully wrap the film, sweep and throw away the trash.

Worker safety

Be sure to wear glasses. The eyes are a very important organ to be ignored and not protected during work. Because in the event of a fragment hitting the eye, in the best option, you will have it removed in the hospital. And there is no need to explain the worst cases. You can lose your eyes "without difficulty" for the rest of your life.

Hands also need to be protected using special thick gloves (remember tiles are sharp material). In order to protect yourself from dust entering the lungs, you must wear a respirator that can be purchased at any nearest pharmacy. If you don’t have a respirator, then the best option would be to make a protective mask using a cloth or gauze soaked in several layers.

How do you get old tiles off walls?

We take up the removal of the old tile. At the beginning of the removal process, they are taken for the top row and gradually move to the bottom. However, in no case, on the contrary, so that the entire wall does not collapse at the same time. Be extremely careful!

You need to detach the tile using a chisel or chisel. They knock it down one by one, carefully picking it up from the sides. In some cases, if the tile does not lend itself, then it is destroyed by gentle hammer blows. In this case, the tile will shatter into pieces and can be easily pulled out.

Dismantling is followed by wall cleaning: the old mortar is removed. At this point, you will need a chisel and a hammer. Clean the wall diligently so that the new tile lays down qualitatively. The finished surface must be smooth, even small pieces of mortar are not allowed. That's all - your work is completed. It is only necessary to clean up the film with the remnants of the old tiles and release the wrapped objects from the blanket.

1. Do not assume that DIY tile removal is easy work. It can take several hours. However, it is not necessary to be afraid of it, the main thing is to be careful not to harm yourself and others.

2. With careful work and following all of the above recommendations, there will be no problem situations. Carelessness and recklessness can cause surface damage and complications further work. You need to be as careful and focused on the robot as possible so as not to harm the wall surface.

3. Be sure to use a puncher in your work. With it, you can quickly and conveniently do all the work that would take more than one hour with manual dismantling. By carefully applying a few gentle strokes, this tool will not be able to damage the surface of the wall. While doing work with a hammer, it is unrealistic to correctly calculate the impact load.

4. Pay great attention to the exit points of fasteners and pipes. Proceed slowly here, planning each hit. You need to hit the hammer carefully, slightly knocking on the chisel. There is no way in the world to swing and strike powerfully at the chisel. One reckless move and you will gouge a cavern into the surface of the wall. It will later need to be puttied, and this is extra work.

5. When it is necessary to remove a single tile without damaging adjacent ones, then in this case a special technology is used. Initially, using a spatula, remove the grout around the perimeter of the tile. After that, using an electric drill, they make holes (about a dozen) in order to easily split it.

6. Additionally, you can still draw tiles diagonally using a glass cutter - this will make it possible to divide it according to the outlines made. The best removal of the old mortar will give you the opportunity to put in a new one later. The surface after finishing should come out bare with the least residue of mortar and tile adhesive.

The easiest way to remove

How to remove old tiles from the wall if you do not have a puncher? We will talk about this further. To this end, we place the spatula in the center of the top tile and destroy it with a powerful blow. After that, we move the spatula into the created gap, trying to hammer it in the most deeply, tapping on it. After that, pressing on the spatula as if on a lever, we detach the pieces of tiles from the wall.

In order to easily remove the remaining tiles, you need to hammer in a spatula from the outskirts and pull it out sequentially, row by row. We hammer in the tool from the beginning of the outskirts and, tapping on it, we hammer it again deep into the old tile. Further, the spatula can be used as a lever.

Be disposed to the fact that the tile may not come off completely and completely, but crack and break off in pieces. When you clean the wall, the mastic on which it was strengthened is softened using a fan heater and scraped off with a scraper. Hold the fan heater at a distance of fifty millimeters from the wall surface.

If the tile is laid evenly, then you can lay a new one on top of the old one, even without dismantling it (for this, it is recommended to put a small one on top of the old tile metal mesh for better grip). The evenness of the surface is controlled using a level. Provided that the old tile breaks off the wall, it will certainly be fixed with mortar before laying the new tile.

Conclusion! In total, the work spent on dismantling the old tiles justifies the results, forming suitable conditions for further installation of decorative processing.

One of the most common finishing materials is tile.

Its dismantling is very simple, but do not rush and immediately get down to business, because the tile is a fragile material, fixed with cement mortar.

Therefore, excessive dismantling activities can lead to dangerous splinters and dust.

Preparing to remove tiles

Let's look at how to properly hit the tile:

1. Cover the flooring with protective material (boards, rags), unless, of course, it is to be replaced.
2. Appliances, furniture and other household items must be removed from the room or covered, as everything will be covered with dust.
3. It is often necessary to beat off the tiles in the bathroom, so it is imperative to prevent construction debris from entering the plumbing.
4. You must not forget to take care of your safety: clothes should be long-sleeved so that there are no exposed skin. Gloves are on the hands, closed shoes are on the feet, goggles are on the eyes, and the respiratory organs must be protected with a respirator.
5. Tool preparation: hammer, chisel or perforator.
6. If the work will be carried out in an apartment of a multi-storey building, then it will not be superfluous to warn the neighbors about the upcoming noise.

Dismantling tiles from the walls - remove a few fragments

After preparatory work you can start dismantling. This process does not belong to the category of pleasant things, so the question arises: how to quickly beat off the tile? The speed of dismantling directly depends on the quality of fastening the tiles to the wall and on the tool used. Therefore, if time plays an important role, then it is better to get a puncher with “peak” and “blade” nozzles.

The surest way to start the dismantling process is to search for " weaknesses» in tiled masonry. It is better to look for it at the top of the wall - this will reduce the risk of dangerous fragments falling. If all the tiles are held tightly, then you need to carefully break one of the cells by hitting it in the center with a hammer or a puncher's lance. Fragments need to be picked up with a sharp object. After removing a few elements, things will go faster.

How to remove tiles from a wall - remove everything

After several fragments of the tile have been beaten off, you need to try to open the hardened cement and beat the next tiles along with it. If this is not done, then you will have to do double work, because the cement must also be removed.

The further process does not present any particular difficulties. You just need to hit the chisel with a hammer, directing it at an acute angle to the wall. With a perforator, it won't take long.

If tiles are removed from a plasterboard wall, then there is a possibility that the wall itself will be damaged. Therefore, when carrying out dismantling, extreme care must be taken.

Removing floor tiles

You can beat off the tiles from the floor with the same means as the tiles from the wall. This process is safer, since the fragments do not scatter from a height, and another plus is the convenience, because you do not need to climb up to the ceiling.

There is one way to carefully beat off the tile without damaging it. A hammer drill is not suitable for this purpose. You will need a sharp knife, a chisel, a strong spatula and 2 hammers (one of them is rubber). The first tile will still have to be broken. Then remove all glue.

With a knife, you need to remove the putty between the tiles, and try to crawl under it with a thin spatula, removing some of the glue or cement. Next, with a rubber mallet, tap the tile abundantly, then work again with a spatula. Thus, it is necessary to loosen or weaken the connection of the tile with the base to the maximum. If there are signs of weakening, then you can try to use a chisel and a metal hammer.

This method does not guarantee 100% saving of tiles, but some part can be saved. To increase the efficiency and speed of work, you can use the "grinder" to remove the putty between the tiles.

Now you know how to properly beat off the tile without damaging yourself and the surrounding objects. You also know how to dismantle tiles without damaging them. Whichever method you choose, remember that health is the most precious thing and cannot be replaced like tiles, so follow safety precautions.

Ceramic tiles are one of the most practical wall and floor coverings in the bathroom. But any, even the most best tile sooner or later needs to be replaced. Whether you decide to update the tiles or replace them, for example, with plastic panels, you must first dismantle the old one. How to remove tiles in the bathroom: what needs to be done for this, what steps to follow and what to foresee - we will consider in this article.

Ceramic tiles in the bathroom

1. First you need to clear the space for future work as much as possible. We take out everything that can be taken out of the bathroom. It is also advisable to dismantle the faience plumbing, since when removing the tile, a piece of it can fly off to the side and damage items in the bathroom. If dismantling is not possible for some reason, you need to cover the furniture, bathroom, toilet bowl, sink, lamps and mirrors with dense material.
2. It is recommended to turn off the water supply to prevent flooding if there is a risk of damage to the pipes.
3. It is very important to take full responsibility for ensuring personal safety. The tile crumbles and breaks off when removed, the fragments can damage the skin or eyes. Wear heavy clothing with long sleeves, goggles and gloves. Cement dust or glue residue can get into the lungs, use a respirator to avoid this.

Work plan

Make a work plan. It really doesn't matter where you start: from the floor or walls, but a clear plan of action will save you time. It will depend on whether you want to keep the tile intact or just dismantle it without saving. The set of necessary tools will also depend on this. Generally, rough plan work might look like this:

• Preparatory work;
• Dismantling tiles from the bathroom wall;
• Dismantling tiles from the floor;
• Cleaning and leveling of walls;
• Cleaning and leveling the floor;
• Final work.

Dismantling with preservation of tiles

Removing grout in the joints between tiles

Here you should immediately warn that 100% saving of the tile will not work. Especially if it was installed on cement mortar by all rules. If the tile is held on with a special adhesive, you have a chance to get some whole tiles. To do this, follow these steps:

1. Treat the seams between the tiles with water using a spray gun or a regular sponge. This will help soften the seam and make it easier to remove.
2. Remove grout in tile joints. To do this, you can use a spatula, screwdriver, knife or angle grinder with a disc nozzle for concrete.
3. If the grout does not lend itself well, try aiming at the wall heat gun for a few minutes. In some cases, this helps and it can be easily removed.
4. After the grout has been removed, pass the corner of the spatula into the resulting empty space and try to carefully remove the tile.
5. If the fragment does not lend itself, use a chisel and hammer to separate it from the wall.
6. You can also use special wire hooks. On two small pieces of strong wire, the ends are bent and they are brought under the empty space on both sides of the tile, after which the hooks are pulled towards themselves.

Dismantling without saving tiles

Dismantling tiles with a perforator and a jackhammer

This method is much easier, because you can not worry about carefully removing the stove and use special electric tools. To break is not to build, but there are nuances here too. Be sure to evaluate the condition of the wall under it after removing the first tile. If the wall has been leveled and the remains of glue or cement mortar are easily removed, be careful when working with a hammer drill and do not make notches on the wall. In this case, you will have less work with further repairs.

If the wall is not even, and large pieces of plaster crumble along with the tiles, you will most likely have to do a lot of work and clean the wall to a concrete or brick base.

To remove tiles, use a perforator with a special nozzle in the form of a spatula. Try not to break the tile, but act like a chisel, leading under the edge of the tile. Even if you don’t need a whole tile, it will be much easier to dispose of it than to collect small fragments. Be sure to take precautions and do not remove a row of tiles that is higher than you. For these purposes, use a footrest.

Choose a rotary hammer with an anti-vibration system and with the ability to adjust the impact force. I wish it wasn't heavy.

Dismantling tiles on drywall

Removing tiles from drywall

If the drywall has not been sufficiently processed before laying the tiles - with putty and other mixtures, it is unlikely that it will be possible to remove the tiles without damaging the base itself.

In any case, you can try and remove the tiles using gentle technology - that is, with the preservation of both the tiles and the wall itself. What does the first condition - saving the tile will most likely be done without difficulty. But to save the wall will have to try.

Remove the grout, after wetting the entire area to be treated with water, using a chisel, chisel and hammer, try to separate the entire tile, starting from the top row.

If the drywall is only partially destroyed in small volumes, these areas can be puttied under the next laying of tiles.

In the case of large-scale destruction, of course, drywall will have to be removed. You can remove it immediately without first removing the tile. To do this, use a perforator to make holes in several places through which you can remove the screws. Cut out part of the wall along with the tiles with a hacksaw.

Removing one tile

There are also situations when you need to remove only one or a few tiles. If it was laid recently up to a week, then dismantling will not cause much difficulty. Clean the grout and use a spatula to remove the tiles. If the laying was carried out for a long time and it took a repair of pipes or other communications under the tiles, you will have to work a little.

The main condition here will not be the preservation of the tile itself, but the integrity of its environment. Thoroughly clean the tile joints and use a hammer and chisel. If the fragment does not lend itself, take a puncher and drill several holes in the desired tile. Then, using the same chisel, gently chip off pieces of the tile until it is removed. If there is drywall under the tile, carefully cut it along the tile joint along with the tile.

For the future, it will be useful to make a hatch for access to all communications, if they are under the tile.

Final works

It is necessary to carefully process the walls, remove with a spatula or knock down the remnants of glue and cement with a perforator. To remove glue, you can also use a grinder with a special grinding nozzle.

After the case is completed, you will have a bunch of construction debris left - do not take it out into the trash cans near the house - firstly, this is prohibited by law, and secondly, it is fraught with a fine. Arrange with a management company or a special organization for the removal of construction waste. If possible, take it yourself to specially designated places.

You can remove the tiles from the wall completely, remove several parts or replace one. How to remove a tile from a wall without keeping it intact is quite simple: a puncher is picked up and the coating collapses, regardless of everything that is being done around. And what to do when a tile or part of it needs to be kept intact? This article will discuss how to properly remove tiles from the walls.

There may be several reasons why you need to dismantle the tiles from the walls.

This is:

• Restoration of the cladding by replacing one or more elements damaged during operation.
• Complete cover replacement.
• Laying a new tile pattern on part of the wall, instead of a boring image.

The way how to beat off the tiles from the wall depends on the need to preserve the facing material. Tile good quality, used, may have a decent enough appearance. It can be used for tiling a balcony (see How to tile a balcony: original and durable cladding) or rooms in country house. The repair cost will be much lower.

If plans do not include reuse of the coating, it is possible to knock the tiles off the wall more in a simple way- completely breaking the old coating, keeping the wall under it as undamaged as possible.

Tile removal methods

Before you beat the tile off the wall, a method for dismantling the old coating is chosen, which depends on:

• The mortar that was used for gluing the tiles.
• The need to reuse the material.
• If the tile was glued to the cement, and he also grouted the tile joints, the chances of saving the parts intact are very small.

The difficulty of removing tiles from the wall is affected by:

• The material laid on the adhesive can be removed more easily.
• It is difficult to remove the old tile without splitting, its material is “tired” and it can burst and crumble.
• If the cladding “boils” in some places, then it will not be possible to obtain parts without splitting them.

Do-it-yourself tile removal methods are presented in the table:

Removal method	Process technology
Clean tile removal
If you want to leave the tile intact, for further use, the dismantling of floor or wall tiles begins in the same way - the grout is removed from the tile joints.	When performing the process, the seams are well soaked with water, and then the grout is removed with a knife or spatula. Sometimes this has to be done in several stages, each time, abundantly wetting, butt joints. This method removes only soft grout.
	The remaining solution is removed with a metal spatula.
One of the tiles is broken with a hammer and a chisel, preferably the top one.	Having broken one of the tiles, you can proceed to the next step.
	All seams between tiles are completely cleaned, trying not to damage the tiles. The depth of cut should be slightly greater than the height of the tile, which will help reduce the chance of chipped corners. It is almost impossible to save tiles laid on cement mortar.
All elements are dismantled with an iron spatula or a thin chisel	A chisel or spatula is driven under the edge of the tile, as shown in the picture. On them gently, but with strong blows, it is tapped with a hammer. The spatula or chisel is moved under the other edge of the part, and tapping continues. Thus, gradually you need to go down, removing row by row.
Dismantling tiles with steel wire	If the tile on the wall is not held firmly enough, it can be removed with a special hook made of hard steel wire. For this: The grout is thoroughly cleaned so that hooks can be driven under the tile. When removing the tile, the steel wire is pushed with a bent end under different sides of the tile. Slowly, the wire is pulled towards itself. In this case, the ceramic can easily separate, making a characteristic click.
Drywall tiles are removed only when one or more parts are replaced.	When applying tile adhesive to drywall, it adheres very strongly to its surface. After removing one or more boards, the section of drywall damaged by glue must be cut out and replaced with a new one. In any case, the methods are the same as described earlier: A chisel is driven between the tile and the adhesive. The tile should fly off by itself. If this is not the case, it is “gnawed out” along with the plaster. After finishing dismantling works the damage that has been done to the drywall is assessed, and the question is how to proceed: is it better to replace it with a new one? In this case, the adhesive residue on the drywall plays a role. It is very difficult and long to remove it, carefully cleaning it with special nozzles for the grinder. After laying the tiles under the comb, old glue you can leave it on drywall, then reprime the walls (see Primer for drywall - why you need it) and cover with a thin layer of mortar. It will hide the bumps from the notched trowel. Tip: If the old adhesive doesn't stick very well or if it falls off, the new tile won't last long. Glue must be carefully removed.
	After dismantling, the whole tile is cleaned of adhesive or cement residues. In this case, the choice of tool depends on the mortar used for laying. The sequence of work is as follows: Pre-soak the tiles for up to 12 hours, but not less than five. This will make the surface easier to clean. If it is not too hard glue, a regular metal spatula is used. Solid adhesive mixture or cement can be removed with an emery stone.
Tip: Be very careful when removing glue residue. At the same time, the chance of splitting the tile is much higher than when it is dismantled from the wall.
Complete removal of tiles
	The process is accompanied by noise and formation a large number dust. The device after connection is attached to the gap between the tiles and breaks them. Elements are removed quickly, and the wall remains of high quality.
	The chisel is driven under the edge of the tile and the hammer hits it with force. By pressing on the chisel like a lever, pieces of tiles are separated from the wall. At the same time, the tile is separated in pieces, cracked and broken off in parts.
Old mastic is removed from the wall	After the wall is released, the mortar on which the tiles have been laid is softened with a fan heater and then scraped off with a scraper. The fan heater should be kept at a distance of five centimeters from the wall surface.

Removing damaged tiles

During the operation of a tiled room, damage to individual parts of the cladding is possible.

It's possible:

• From mechanical impact, resulting in cracks or chips.
• When individual tiles fall out, partially capturing adjacent broken fragments. This situation is possible from the violations committed in the preparation of the surface for laying tiles.
• The wall was not corrugated after it was painted, for better adhesion of the tile adhesive and the main surface.

Removal of an individual damaged tile must be carried out with pinpoint accuracy to prevent damage to the entire cladding located nearby.

Tip: When carrying out work, strong impact on the wall should be avoided so as not to provoke the remaining tiles to lag behind.

Part removal instruction:

• The joints located around the defective tile are cleaned of grout.
• With a cutter, diagonals are drawn along the ruler on the tile, connecting opposite corners to the part.
• Several holes are drilled with a thin drill, starting the process from the center, at the intersection of the diagonals. This loosens the ceramics, as shown in the photo.

• With a chisel and hammer, separate pieces are carefully beaten off.
• The wall is cleaned of adhesive residue.
• The surface is primed.
• A new tile is being installed (see How to install tiles on a wall).

Tip: buy ceramic tiles, is always necessary with a small margin, in case of repair of the facing surface, during the operation of the premises.

A more complete picture of how to remove tiles is presented in the video in this article.

Wall tile removal technology

The dismantling of any coating begins with the acquisition of the necessary tool, the set of which depends on the chosen method of removing tiles.

• being prepared workplace for convenience and efficiency of work.
• The floor is covered with plastic wrap, which will facilitate the collection of debris, which will scatter in all directions during operation.
• If it is in the bathroom or toilet, an old blanket is placed on the plumbing, protecting them from splinters from the old tiles.
• At the end of the work, you only need to carefully roll the film, and then throw it away.
• Be sure to use eye, respiratory and hand protection.

• The tile is removed from the wall in the chosen way.
• The wall is cleaned of old mortar so that the surface is even, without pieces of mortar.
• Garbage is removed from the premises.

There are many ways to remove tiles from a wall without damaging it. The main thing when carrying out work is to choose the best option, to carry out all work carefully and slowly. Then the tile can be used not only for lining utility rooms, but also in the bathroom and in the kitchen.

Any apartment or Vacation home periodically in need of repair. Sometimes it is enough to change accessories and furniture to make the atmosphere fresher and more cheerful. But in most cases, you will have to work on a more thorough alteration. If everything is clear with the replacement of wallpaper and painting the walls, then the question of how to remove the tiles from the wall can drive many into a dead end. Especially if this process must be carried out carefully, without damaging the tile.

In fact, dismantling is not a big difficulty. Most importantly stock up necessary tools and determine how the tile was glued to the wall (using cement or adhesive mortar). It happens that the old tile needs to be removed not completely, but only some part of it. Then you should be especially careful not to damage not only neighboring tiles, but also the wall in the kitchen itself.

What will we need?

It is almost impossible to completely clean the surface of the tile and not damage a single fragment. But if you show accuracy and a little skill, it is quite possible to keep the tile intact as much as possible. How successful the work will be depends primarily on the quality of the laid tiles and on the adhesive composition, as well as on the statute of limitations.

The work may require the use of the following tools and materials:

• drill and perforator;
• metal spatula;
• hammer;
• scraper to remove the grout;
• knife
• chisels.

Do not forget about the precautions. Dismantling old tiles is a dusty and dirty process, so you should stock up on work clothes, special goggles, a mask or gauze bandage, and gloves. To make it easier for yourself to clean up after work, you can lay an oilcloth on the floor.

Dismantling process

If the tile was mounted to the kitchen wall with cement mortar, then it is almost impossible to remove it intact. Therefore, a puncher with a special nozzle is required here. If the tile was attached to the glue, then there are more chances to dismantle it without damage. The easiest way is to remove the tile without preserving its integrity. In the process, you will need a puncher with a chisel attachment. Before starting, you need to put on work clothes, goggles and a mask, as the process will be quite dusty with a lot of flying small fragments. Cement mortar remaining on the wall after removing the tiles can be removed with a hammer.

The neat way requires a lot of effort and skill. Here it is necessary to use a sharply sharpened knife and a spatula to remove the grout from the joints. To make it softer and more pliable, you can moisten the surface with water using a sponge.

After removing the grout, you should begin to dismantle the old tile. Here you will need a perforator and a flat-shaped nozzle that goes behind the tile to clean out the old mortar. If an adhesive was used during the laying process, and not on a cement mortar, then successful removal without deformation is possible. Otherwise, the tile is likely to crack.

Instead of a puncher, you can use a chisel with a hammer. After removing the grout, you need to put a chisel under the tile and gently, without sudden movements, use a hammer to beat it off the wall.

Deleting multiple items

It is not always necessary to completely remove the tiles from the walls of the kitchen. It is enough to replace two or three tiles on which chips or other defects have appeared. Here you need to be extremely careful with exactly the tile that should remain. The process of dismantling tiles from the central part of the wall or in the corner is considered especially laborious. First of all, it is necessary to soften the grout with water and remove it as in previous cases. A puncher should not be used in this case. Dismantling occurs with a hammer and chisel.

Cement mortar can greatly complicate the task. Therefore, the tiles must be removed carefully and in parts. First you need to use a drill to make several holes in the tile, and then remove it piece by piece with a spatula.

How to remove tiles from drywall?

If the wall in the kitchen is made of drywall, then removing the tiles carefully without damaging either it or the wall surface is almost impossible. The adhesive mortar adheres very strongly to drywall, eating into the surface. You can remove one or more tiles, followed by replacing a piece of drywall. But with a whole wall, everything is much more complicated. You should hope for luck, and carefully proceed to the dismantling process. The chisel must be inserted between the tile and the adhesive and tapped on it with a hammer. The tile either flies off by itself, or together with a piece of drywall. Alternatively, you can try cutting ceramics with a grinder.

At the end of the work, it is necessary to assess the damage caused to the walls and decide what to do with them next. It may be necessary to replace individual sections of the drywall structure.

Removing old tiles from a wall is not as difficult as it might seem. As in any other repair business, it requires careful preparation and deliberate action. If you stock up on the necessary tools and materials, study the tips and choose the most appropriate method of dismantling for yourself, then you can cope with the task without resorting to the help of specialists.