home Window

Water tank from a wheel for a vegetable garden. Do-it-yourself tire drain pit: step-by-step instructions for arranging Options for decorative solutions for a tire pond

Every living being or plant needs water. Therefore, if there is even a small land plot, it is necessary to take care of its reserve. Even in modern time when there is a central water supply, wells and wells, there are times when water disappears. It mostly happens in hot and dry weather.

metal container for water

In this regard, in order to prevent the death of garden plants, it is recommended to place a container for a reserve supply of water in a darkened area. If necessary, which can be used at any time for its intended purpose. Such vessels are made of metal or plastic, and are also industrial or home-made.

The material from which the metal container is made is selected primarily from the purpose of the liquid stored in it.

Water tank - the right item on the site

If the water will be used for drinking and cooking, then the tank should be:

It is made according to GOSTs from stainless and high-quality steel;
Equipped with a hole for ventilation;
Have a tight-fitting lid
The ventilated opening must be protected with a special mesh to prevent debris from entering the inside of the vessel;
For convenience, you can embed a water tap into the container;
Provide for the presence of a hatch in the side of the vessel. With it, it will be convenient to wash the barrel.

To ensure that the quality of drinking water does not deteriorate, the barrel must be washed at least twice a year.

If the nutrient moisture is intended for watering plants or other household purposes, then the reservoir for it can be used from any component. For such needs any will do even a used vessel, the most important thing is that no chemicals have been stored in it before.

A tank that collects rainwater will help save money on water consumption. For these purposes, it is recommended to take the usual fifty-liter container. You can also use another tank, with special filters already installed that will purify the water. If such a vessel is left for the winter, then thanks to the thawed snow, in early spring the container will be filled to the brim with water.

plastic containers

Such vessels have gained wide popularity due to the following advantages:

The cost is much lower than metal tanks;
Huge selection of various sizes;
tightness;
No need to paint primer and paint;
Do not corrode;
Have long term operation;
Do not respond to sudden changes in temperature;
Frost-resistant, some materials withstand thirty degrees of frost.

A plastic vessel is made of technical or food plastic, it all depends on its purpose. Plastic for food barrels is made of frost-resistant and high-strength plastic, which does not transmit ultraviolet radiation. That is why, life-giving moisture retains its positive qualities for a long time and does not deteriorate.

Almost all barrels are equipped with a threaded hole with a plug, which is designed for trouble-free installation of a faucet. When purchasing such a container, it is necessary to check the availability of a quality passport.

Plastic vessels under water have a very wide variety of shapes, and are both horizontal and vertical. At present, the shape of the European cube is widely used. Such containers are made of a polymeric material, which, for greater stability, is equipped with a metal wide-band grate from the outside.

At the top of this vessel there is a wide mouth, which allows you to fill the plastic cube with water using a bucket or hose. Below, the manufacturer provides a valve for draining the liquid.

A barrel in the form of a cube is readily used by users to equip showers, water plants, and other significant household needs.

Do not forget that eurocubes are often used to transport various liquids, including chemicals. Therefore, it is not recommended to use them for storing drinking water.

In construction hypermarkets, you can purchase a drinking water tank that has a certificate of conformity. However, such a capacity will cost a lot of money. Therefore, in order to save a certain amount of money, the tank can be made by hand.

Handmade container manufacturing

Do-it-yourself water tank can be made using used tractor tires. To do this, you just need to get this material at a low price, or just ask. Then install the tires from the tractor on personal plot, in the following order:

Choose a suitable place for the tank, preferably in the shade;
Level the area where the container will be installed;
Cut out the inner upper part of the tire;
Install the tire on a pre-leveled area;
Prepare cement mortar. To do this, you need to mix one part of cement with three parts of sand, then add water so that the consistency looks like thick methane;
Pour the resulting solution into the bottom of the tire, and use a trowel to level it;
To prevent the ingress of debris or rainwater, you need to cover the tire with polyethylene;
Make a weekly exposure so that the cement mixture hardens well;
After a week, remove the cellophane from the tire and fill it with water.

This device is not suitable for storing drinking water, but you can water plants with such water. Such water is especially well suited for horticultural crops growing in a greenhouse. Because it heats up quickly. In addition, the tractor tire tank is a good rainwater collector. The main advantages of such a vessel are long service life and reliability.

Typically, such designs are made to store a small amount of water. Therefore, if the capacity is needed much more, it is necessary to look for other manufacturing options.

Wooden container

Currently, more and more summer residents began to use water vessels made of wood. Since they decorate well any, even the most nondescript piece of land.

To make a wooden container with a volume of eight cubes with your own hands, you need to purchase the following materials:

Three three-meter wooden beams;
Sixteen bricks, which must be wrapped in polyethylene to create waterproofing;
Ten four-meter boards, at least five millimeters thick;
Six oriented strand boards, measuring two and a half and one and a quarter meters;
geotextile insulation;
Thick plastic film, preferably black;
Self-tapping screws.

To boron all of the above elements, you need to do the following:

Lay bricks on the leveled area around the perimeter so that the distance between them is the same;
Lay three beams on the bricks;
Using self-tapping screws, attach five boards to the beam;
Place and attach OSB boards on top of the boards;
Make a frame from the boards and fix it on the base;
Sew up the frame with the remaining sheets of OSB;
Cover the inside of the container with geotextile;
Lay a film on top of the sealant so that its edges hang over the edges of the vessel;
Fill the tank with water;
For greater reliability, fasten the film from the outside with a stapler;
On top of the vessel, nail two halves with a cross.

The main advantages of such a vessel are:

Not high costs for the purchase of necessary components;
Not hard to make with my own hands;
Easily disassembled and moved to another location.

The negative points include the fact that the water in such a tank will not be potable.

For more information on how to build a greenhouse from plastic pipes, we will tell in our material.

Here our readers will learn how to make a fence from a profiled sheet.

Is there a well on the property? Here you will learn how to choose a submersible pump for her.

Summer shower containers

Usually, all summer cottages are equipped with a summer shower, which is located on the street. Such a shower can be filled with a hose or bucket from a well, well or water pipe. However, for human body too much cold water not very useful in hot weather. Therefore, before using the water, you need to warm it up a little.

In order not to buy expensive automatic heaters, you can install a plastic or stainless steel container on the shower roof, which, thanks to the sun's rays, will quickly heat up.

by the most the best option for a shower, a vessel made of galvanized iron is considered. It is not too expensive and has a long service life.

In contact with

Classmates

vokrugdachi.com

Do-it-yourself country water tank

Samodelkin 8-01-2010, 17:26 62 127

In contact with

It makes no sense to prove the need to have a supply of water for irrigation on the site. If something happens to the irrigation system, and your flowers and vegetables will turn into hay during the days of the July heat. When my old steel tank leaked, I needed to urgently find a replacement for it. Having assessed the harsh reality, I decided to make a structure that would decorate the site, be durable, inexpensive, and not attract “guests”. After going through different options, I chose, it seems to me, the most successful one: to make the base of the container from sheets of galvanized steel, “dressing” it in concrete. I connected the sheets of steel measuring 1000 x 2000 mm to each other with a ring. In order for the container to have a volume of 1 m3, I made a ring of 2 sheets. The seam before “pressing in” was treated with sealant for plumbing work, as well as all subsequent seams. It turned out a springy flexible ring, which can be given any shape. For a capacity of 1 m3, it is enough to make a foundation 120-150 mm thick, laying it on a cushion of rubble. The area of the foundation must be larger than the area of the container. Having chosen a place, he took out the soil to a depth of 200 mm, filled the pit with rubble and sand, rammed it, spilled it with plenty of water, and prepared concrete. I laid out half of it on rubble, on it - reinforcement made of steel rods and pipes, and poured the rest of the concrete on these structures. Water should be added to the concrete so much that it does not spread, but resembles gingerbread dough. This does not require formwork, and the edge of the foundation will look like stone "nodules". Concrete is not poured into place, but is laid with a shovel and rammed, or with a wooden mallet. The next operation is the installation of a metal base. The laid concrete is carefully leveled. To do this, he poured a cement-sand mixture (1: 3) of the consistency of liquid sour cream onto the foundation and dispersed it with an even rail. Letting the leveling layer dry (lose fluidity), put a sheet of galvanized steel on it and pressed it with bricks. This is the bottom of the future tank. Previously, the sheet was cut to fit the configuration of the container and protruded along the perimeter by 20 ~ 30 mm. In this state, the foundation was left to dry for a day. A day later, a manufactured ring made of galvanized steel was installed on the bottom, having previously made 2 holes in it: one at the bottom at the very edge for the drain pipe, the other 300-400 mm above the edge for the selection of clean water. If all the previous work was done carefully, then gaps in some places of no more than 5 mm are permissible between the wall and the bottom - they will not affect the quality of the container. Having installed the wall and fixed it with bricks, he overlaid the joint between the wall and the bottom with a steep but plastic "dough" from a mixture of cement and sand (1: 1) with the addition of PVA glue (1 tbsp. spoon of glue per 0.5 l of water). After drying the "dough" for a day, he removed the bricks and completed the sealing of the joint in the places occupied by the bricks. Having completed the sealing of the joint, I installed a tube (aluminum, stainless steel, plastic) into the wall hole at the bottom, carefully overlaid it with a cement solution. Then he proceeded to the construction of a concrete wall. The concrete for the wall is prepared the same as for the foundation. He performed the work as follows: he took a portion of concrete with a trowel, laid it against a steel wall (it played the role of a one-sided formwork), lightly rammed it so that the concrete spread and pressed tightly against the wall. And so around the perimeter. When laying concrete, one must strive to ensure that the wall thickness is not the same. Then a surface is formed that resembles the natural texture of a stone. At the same time, you can show your abilities as a sculptor, guided by a sense of beauty and harmony. When constructing a wall, one should not forget that a drain pipe should go out at the bottom, and at a height of 200-300 mm from the bottom, another pipe with a thread for the valve must be mounted into the wall to select clean water. So that during the laying process the steel base does not deform, it is advisable to lay brick columns inside the tank, which do not allow the wall to “go” inside under the pressure of concrete. concrete. The last stage is finishing. Various options are possible using ceramics, bottle glass, natural stone, etc. I chose a simple option: the entire surface of the container was smeared with a cement-sand mortar (1: 1) and treated with a wet broom. Grey colour cement looks good in the greenery of the garden. Such a container has many advantages, it is quite cheap, there is only one drawback: it cannot be moved. Therefore, the place must be chosen carefully, remembering that a capital structure is being built.

In contact with

To write a comment, you must enter the site through the social. network (or register): Regular registration

Information

Visitors in the Guests group cannot leave comments on this post.

usamodelkina.ru

Water tank

People, plants, animals need water. Without it, they cannot develop and exist. And therefore it is important to have a stock of it on your site. Of course, almost everywhere there is running water, wells, wells. But there are circumstances when the water disappears. This happens most often in hot, dry summers. And then all your labors invested in flowers, vegetables, fruit trees and shrubs will disappear. It will be painful to watch your plants wither.

To avoid such sad situations, it is recommended to install a storage tank for water on your site.

According to the materials of manufacture, they are:

metal;
plastic.

According to the manufacturing method to be done on:

industrial;
homemade.

metal container

Depending on what the water will be used for, choose what material the metal container should be made of.

If the water is drinking, for cooking, washing, then the water tank must be made of high-quality, stainless, gost steel. Such a tank should have a ventilated hole with a tight-fitting lid. It is a good idea to install a protective grid on this hole. A water faucet is embedded in a stainless steel container.

Twice a year, it must be washed with disinfectants so that the quality of drinking water does not deteriorate. Therefore, in the side part there is a hatch through which it is possible to wash the stainless steel barrel.

If you will use water for technical needs:

glaze;
household purposes;
rainwater collection,

then you can purchase a tank from any metal.

In order not to increase the consumption of drinking water, it is best to install a rainwater collection tank in the country. It can be either a simple fifty-liter metal barrel or special storage tanks with filters for water purification.

And if the barrel is inexpensive, besides, you can use a used one, the main thing is that chemicals are not stored there before, then special containers for collecting rainwater are quite expensive. True, the water collected in them can be used for washing and for watering. But in barrels you can leave water for the winter.

plastic container for water

These containers are the most popular. The advantages of these containers:

cheaper than similar ones made of stainless steel;
a large selection of different volumes;
tightness;
do not require additional care (painting, primer);
do not rust;
long service life;
not afraid of temperature changes;
withstand 30 degree frosts.

The plastic container can be made of both food-grade plastic and technical plastic.

Plastic food barrels are made of high-strength, frost-resistant plastic. It does not transmit ultraviolet rays, so drinking water in them does not deteriorate for a long time.

Most of these barrels are equipped with threaded holes with a stopper, the diameter of these holes allows you to install taps in the tank.

Each plastic container has a quality certificate.

Plastic containers can be vertical and horizontal.

Eurocubes are in great demand, which they willingly purchase for the dacha. They are made from polymer materials, for greater stability, the cube is placed in a metal crate. It has a neck at the top and a drain cock at the bottom.

Cube containers are widely used in private households. They can be used as a storage tank for:

glaze;
soul;
household needs.

It is worth mentioning that eurocubes are used to transport various liquids; they cannot be used as containers for drinking water.

If you have enough money, you can buy a factory-made water tank for your summer cottage.

But, having spent a little time, you can make a water tank with your own hands, and it will be no worse than the factory one.

How to design a container yourself

It is very easy to make an unusual storage water tank from old tractor tires with your own hands. To do this, you just need to purchase decommissioned tires of large diameter and install them on your site.

The container can be easily installed with your own hands, for this:

Align the place where the container will be located well.
Cut out the upper inner part of the tire.
Place the tire on the prepared surface.
We take three parts of sand, one part of cement, diluted with water to a state of thick sour cream. We mix everything well.
Pour the bottom of the tire with the resulting solutions, level the surface.
We cover the tire with cellophane so that water does not get in in case of rain. We wait a week until the solution hardens.
Remove the film and fill the tank with water.

The water that will be stored here is, of course, unsuitable for drinking and washing. But on the other hand, it will heat up quickly, and it will be possible to water the plants in the greenhouse with it. In addition, the tank will serve as an excellent reservoir for rainwater. The advantage of the tank is reliability and durability.

Such containers are suitable as a fallback for a small amount of water. If you need a large volume, then it is worth making storage tanks more solid.

wooden water tank

To make a container that can hold 7 m3 of water, you will need:

three beams three meters long;
sixteen bricks wrapped in polyethylene for waterproofing;

ten boards with a length of at least 3.5 meters and a thickness of 0.5 centimeters;
six OSB boards 2.5x1.25 meters;
geotextile insulation;
black polyethylene film.
self-tapping screws.

Manufacturing steps:

Along the perimeter of the leveled area, we lay out the bricks at the same distance.
We lay three beams on the bricks.
We fasten five boards to the beam with screws.
We attach 2 OSB boards from above with self-tapping screws.
We make a frame from boards, fasten it to the base.
We fasten the remaining OSB sheets along the frame.
We tighten the container from the inside with a geotextile attached from above with brackets.
Then we lay the film, hanging freely over the edges of the box.
We fill the container with water.
For reliability, we fasten the film from the outside with a stapler.
On top of the container we nail two boards with a cross.

Advantages of this container:

low cost;
just do it yourself;
easy to disassemble, move to another place.

True, to use such a container, a pump is needed, and the water in it will not be potable.

Containers for summer shower device

On a hot summer day, after working in the garden, you want to take a warm shower. But in order for the water to be hot, you need to heat it. You can buy an electric heater for the dacha, but it's not economical.

It is easier to install a storage tank in which water will be heated by the sun. Any barrel can serve as such a container - galvanized, stainless steel or metal, plastic.

To do this, just set the container at a height and fill it with water.

The easiest way to install plastic containers.

A stainless steel container will not rust, the water in it will not bloom, it will be drinkable. But stainless steel products are expensive.

An alternative may be a galvanized barrel, of course, it is not so durable, but if the galvanization is not broken, it will not rust either.

Most economical option- this is a metal water tank, but it must be painted to protect it from corrosion.

Was this article helpful?

The best Water Tanks in the Country - which one to choose

Water tank in the country - idea photo

We will not deny that water storage tanks are needed on any suburban area. During the first year of owning a summer cottage, my husband and I suffered greatly from the fact that we had to carry water all the time in buckets from a water tower located 500 meters away from us. After some time, we had a suitable container for water in the country - a 250 liter blue plastic barrel.

Container for storing water in the country

Yes, this greatly simplified and improved my life in the country - the water tank is used up in three days, and we have water in the water supply just every three days. So replenishment with fresh water occurs regularly.

Such a capacity is especially relevant if there is no running water in the country. In this case, you can think about a rainwater storage tank, at least you will have industrial water for irrigation. And you can collect precipitation just in such containers.

Ideas for containers for storing water at their summer cottage

The most common water tanks are 100 l, 250 l, 500 l, 1000 l, 5000 l. Very convenient plastic container - eurocube, reinforced with a metal frame. Calculate your own water consumption for each family member and purchase a slightly larger water tank, so to speak, in reserve.

Plastic tanks for storing water in the country

If your consumption, like ours, is small, then you can purchase water containers for a summer cottage of 100 liters, 200 liters, 1000 liters. If the volumes are not enough, then several small containers can be combined into a single whole, while receiving a significant increase in the total cubic capacity.

If your family and consumption are large, then immediately take water containers of 2000 liters, 3000 liters or 5000 liters. Of course, you need to understand that large volume containers are very expensive.

Container for storing water at their summer cottage

So, decide for yourself what volume you need a container for storing water in the country?

Water tank shapes

The most versatile are rectangular water containers. They can be easily placed in a corner, connected together, stacked one on top of the other. the same applies to rectangular containers - there are a wide variety of them on the market.

Such containers are often used for the accumulation and storage of drinking water, or industrial water for irrigation and showering.

Large capacity for collecting rainwater in the country

Round water tanks are also very popular - a similar tank for giving can be installed on a pedestal and get natural water pressure in your summer plumbing. And cubic water tanks and rectangular tanks can also be raised to the podium - tower and get a little pressure in the water supply system.

Drinking water tanks - what materials are suitable

When we chose what material our water tank will be made of, we studied the reviews and opinions on the forums. As a result, we settled on plastic, simply placing the barrel in the shade, where the sun does not fall.

The idea to build an artificial reservoir in the country comes to the mind of many land owners. Undoubtedly, such a source of coolness and positive emotions will please not only the owner himself, but also his guests, becoming a real highlight of the landscape. The mere sight of the water surface helps a person to relax, tune in to a lyrical mood, causes bursts of inspiration. But, having critically assessed only six acres of their own land, some give up their dream. But in vain! We will tell you about how to bring it to life by making a mini-pond from a tire with your own hands in the country, and at the same time recycle old rubber that is unnecessary on the farm.

A decorative mini-pond should please and attract everyone's attention. Therefore, the place where it should be located should be chosen very carefully. There are several rules that we recommend that you follow so that the choice is successful:

The pond should not be constantly in the sun. Penumbra - the best place for him. Otherwise, the plants will be too hot, and they will begin to wither, and the water will bloom quickly.
Open and ventilated places are also not the best option.
If you build a pond under the crowns of trees, the water will constantly become clogged with leaves and small debris. The cleaning process will become regular and tiresome for you.

It is good if the pond is clearly visible from different viewpoints. Let beautiful objects be reflected in it: running clouds, a house or trees. Know that small bodies of water look best when viewed from above. Therefore, they are often placed in natural landscape depressions.

In such a place, the mini-pond will be clearly visible from different viewpoints. In addition, it will not be under constant exposure to direct sunlight.

If you doubt your own choice, arrange a test for yourself. Take a piece of polyethylene that will represent a mini-pond and place it in the place of your choice. Walk around the site and see how well it can be seen from the main viewpoints.

Where can I find the right tire?

Before looking for a tire, let's decide what exactly we want to find. If there is a catastrophic lack of space on the site, then to make our dream come true, it will be enough for us to find a tire from any car.

To implement a large-scale project, the size of the wheel must be impressive. After all, there are wheels whose diameter exceeds human height. Using them as a base, you can build a whole lake!

Tires come in different sizes. It is not so difficult to find such a Gulliver among them, and it is hardly necessary if the size of the plot does not exceed the standard six acres.

For large objects, you must have:

tire from KAMAZ;
rear wheel from the tractor "Belarus";
tires from the mighty BELAZ.

If your own unnecessary tire is not lying around in your garage, then a suitable copy can be found in a tire shop. There often accumulates unnecessary rubber to be disposed of, so you will get it for free.

Used tires can also be found at car dealerships. It is possible that you will have to pay there, but purely symbolically. Ordinary car owners can also offer what you are looking for. So check out their ads as well.

What will your reservoir be like?

In a tiny reservoir, it is unlikely that you will be able to get fish. Although goldfish from an aquarium can feel good in a small artificial pond. However, this building can be decorated in other ways. For example, Siberian iris can be planted along its banks.

Perfect companions for any pond

water lilies;
swamp turkey;
floating pond.

In the end, you can also use artificial decorations that imitate the same lilies, but do not require attention. Small imitations of ducks can look good on its surface, and turtles along the banks.

Plants planted around an artificial reservoir can completely transform it, turning it into a favorite vacation spot for all family members.

The rubber base should be securely covered with decorative flagstone so that it would never occur to anyone how a mini-pond was formed on your site. Often, small alpine slides become companions of water structures, which, by the way, solve the problem of creating a shadow.

To provide additional effect, you can highlight the structure with solar-powered garden lights. All the energy that they accumulate on a sunny day, they will use up at night in the form of a soft, mysterious glow.

Pond decorations also have their downside - they attract the attention of kids who love to play in such a fabulous place.

Whatever your mini-pond, you should remember that for small children left unattended, it can become a source of danger.

Step by step instruction

Any work is preceded preparatory stage. We need to put together all essential tool and material in order to be distracted as little as possible in the process of performing work.

Stage # 1 - preparing the tool and materials

We don't need a lot of tools.

two types of shovels: bayonet and shovel;
building level;
electric jigsaw or ordinary hacksaw.

In addition to the tire, with the diameter of which we have already decided, we will need:

PVC film or special covering material for pools, which is sold in specialized stores;
sand;
gravel;
large stones for decorating the banks of the pond;
plants for decorating a pond and framing.

If everything you need is prepared, you can get to work.

Stage # 2 - preparing the tire for work

Despite the fact that we are going to bury the tire, at the first stage of work it must be cleaned of dirt. But her training doesn't end there. We need to cut off its upper part.

It is unlikely that an ordinary knife is suitable for this purpose. We recommend using a low speed jigsaw. You can also use a hacksaw for metal, but then this operation will have to spend more time and effort.

Stage # 3 - digging a recess for the reservoir

Before you make a recess, you need to level the site. Now we need to decide how much we want to deepen the rubber base of the future structure.

She may be:

immersed in the soil for the entire width of its tread;
deepened by one third;
remain on the surface of the prepared site.

Based decision, digging a hole. Its shape should correspond to the outer diameter of the tire, but with small allowances around its entire circumference. You should not completely deepen the rubber base into the pit: if you leave the rubber edge on the surface, rainwater will not flood the container.

Before installing the tire in the resulting recess, it is necessary to level the bottom and fill it with sand by about 15 cm. The sand should be soft and without pebbles. In this case, he will be able to protect the gasket placed on the bottom of the reservoir from damage, and water leaks can be avoided.

When forming a recess for a tire, you need to compact the sand well at the site of the future bottom of the mini-pond and check the level of the quality of the work performed

We check the quality of the work performed. Do not forget to tamp the bottom and only after that place the rubber base on it. After that, you should use the level again to check the horizontal position of the tire.

Stage # 4 - waterproofing device

For the arrangement of waterproofing, it is better to use a dense covering material, which is specially designed to protect the bottom of the pools. You can buy it in specialized stores for pools. Sometimes it can be found among the goods for the garden. The material must be taken in such a way that it protrudes from the tire walls by about half a meter.

Yes, we prefer a special waterproofing material over conventional polyethylene. Someone may argue that because of this, our structure becomes less like a homemade product, for the creation of which, as a rule, improvised materials are used. But it is better to make a design that will serve you for more than one year without replacing the bottom. After all, even very thick polyethylene will not be able to withstand the load and will definitely leak.

However, each owner decides for himself which material is best for him to use. When choosing ordinary polyethylene, consider replacing it when you begin to strengthen the walls of the future pond. The building may need to be demolished.

Even if you fold the plastic film in half, it will leak. To replace it, the mini-pond will have to be dismantled, so the top of the structure will have to be made collapsible

So, the covering material is freely distributed along the bottom of the pit, and its edges are brought out half a meter beyond the edges of the tire placed in the recess.

The membrane of the material must be rationally distributed inside the tire. For this purpose, the future country mini-pond is filled with water, which will put pressure on the bottom and walls of the structure. Under its pressure, the reservoir will take its shape.

Take the time for quality work and you will get an excellent result that you can be proud of for several years

Now the covering material must be carefully straightened. To fix the coating in the desired position, you can press it down with rounded boulders laid on the bottom from opposite sides.

Stage # 5 - form the walls and decorate the pond

We smooth the edges of the material and sprinkle them with sand and gravel. This will permanently fix the membrane. Now she won't slip. Sand will serve as the basis for further decoration of the pond.

Further strengthening and decoration of the reservoir completely depends on the imagination of its author. At the initial stage, you can simply overlay the pond with stones.

If you manage to find a large tire, you can make a mini-pond not only for kids, but also for adult family members.

Options for placing stones depend on the degree of functionality of the structure:

For swimming. If the tire was large, then such a structure can even be used for swimming. The banks of such a pond should not be overloaded with stones. With their help, it is enough to form a platform around the walls. A large number of stones can cause injury to bathers.
For decorative purposes. If the reservoir is needed only to create a beautiful image, you can fantasize with the location of the stones in order to emphasize their beauty as advantageously as possible. In this case, do not be afraid to show their sharp edges. They look spectacular.

Stones can be laid out in several rows, placing rounded and large boulders below, and smaller pebbles on top. Even the bottom of a mini-pond can be decorated with cute, medium-sized oval-shaped pebbles taken from a river or brought from the sea. But it is better not to use sand and gravel to decorate the bottom, because the water from them can become cloudy.

Do not overload the mini-pond with decorative elements. He is so handsome. Even in a minimalist style, it remains a magnificent place that attracts the eye.

In any garden, regardless of the will of its owners, many small animals live. It can be, for example, moles, hedgehogs or mice. If you do not want to find the corpse of an unfortunate hedgehog in the water one morning, place a picturesque snag in the pond. She will not only do appearance structures natural, but also help the animal avoid death.

To visualize the whole process of work, watch the video:

Other ideas for arranging such a pond

If you think that a pond from a single tire is all that the fantasy of domestic craftsmen gardeners could give rise to, then you are deeply mistaken. There are a lot of options for using tires to create reservoirs. And we will tell you about the most popular of them now.

If you take not one, but two tires of equal or even different sizes, you can make not one, but two reservoirs that will be in contact with each other with treads. The most interesting thing in this building will be its decorative design. For example, at the junction of two rubber bases, you can build a beam bridge from birch logs. It can be both decorative and a continuation of the garden path.

By changing the degree of penetration of tires, you can create ponds with overflow. To do this, one tire is fixed on the surface of the site, and the other is buried. With the help of such an overflow, by the way, it is possible to organize the drainage of rainwater flowing from the roof.

On the basis of ponds with overflow, you can make a homemade waterfall. To do this, you need to lead a hose to the upper tank, from which water is supplied under low pressure. It can be carefully camouflaged with stones located along the banks. Water, overflowing the upper part of the structure, will effectively run into its lower half, imitating a waterfall.

If the landscape of your site allows, then why not build such a magnificent waterfall, which is based on the same tires

The swimming pool in summer is something that cannot leave any child indifferent. A large tire will make it easy and simple to make it. Kids will have something to splash around in under the supervision of adults. It is best to surround a children's paddling pool with a coastal zone of tiles so that you can safely step on it with bare feet. To protect the children, the water in such a pool must be filtered. A pump can be used for this purpose. Or you can just change the water more often.

A good idea to enliven a pond is to use a fountain in it. To do this, you can adapt a turbine with a nozzle for an aquarium or a small pump. For the fountain to work, it needs to provide power. Do not forget to protect yourself: the electrical wire must be insulated with a corrugated pipe and buried.

See what the construction of a tire fountain looks like:

Even if there is no meth for a pond in the garden, using a tire, it can be done on a balcony, on a terrace or in a loggia. Artificial stones will help to give the structure an attractive look, which can be glued with a water-based composition to the side surface of the tire.

Of course, this list of ideas cannot be exhausted, because human imagination knows no bounds. Watch this video - we're not fooling you:

Many people assume that building a country pool is an expensive pleasure, and to make it, you need to spend a lot of time and effort, but this is not always the case. Old tires that have served their age, which are lying around unnecessarily, can serve excellent material to create a reservoir at their summer cottage. It is not difficult to equip a small, pretty pool from a wheel with your own hands, it will take a minimum of funds and very little time.

Which wheels are suitable for the pond

The choice of tire depends on the size of the pool you intend to build on the site. If you want to make a decorative pond to decorate the country landscape, tires from cars are quite suitable. But if you decide to make a pool out of a wheel with your own hands in the country, where you can swim, you need to use tires from large trucks, special equipment or a tractor.

For this, rubber from the L-700 or T-150 tractor is suitable, you can use the rear wheels of the Belarus tractor. Even better, if you manage to get a tire from a Belaz dump truck. Its size allows you to equip a pool in which two adults can swim at the same time.

Stages of pool construction

Choose an open area for the pond away from trees. So that over time the base does not blur and crack, it is advisable not to place it in the irrigation zone, but to choose a dry place.

How to prepare a wheel

Clean the tire of all kinds of dirt. To make a pool from a wheel in the country, you will need one side part, and the second will need to be cut off, leaving only the side. Use a sharp knife, and to make it easier to cut, pre-spread the rubber liberally with regular laundry soap. In places where you need to cut the cord, use a hacksaw.

You should not use a grinder to trim unnecessary parts of the tire, it turns the rubber into sticky small crumbs, which will then be very difficult to wash off.

How to make a base

Before deciding how to make a pool out of a wheel, decide how you want to see your future reservoir: so that it rises completely above the ground, or that its body is partially dug into the ground. If the first option is chosen, it is necessary to remove a layer of earth with a diameter slightly larger than a tire for one bayonet of a shovel, fill it with sand and compact it well.

In the second option, you need to dig a hole 2/3 of the wheel height deep, make a pillow of sand or gravel with a layer of about 15 cm, and level the surface. Next, the base under the reservoir must be concreted and a tire installed on it. After that, 2 more buckets of cement must be poured into the center and leveled so that there are no cracks or cracks left inside the structure. The pool will be completely ready in three days.

Drain hole equipment

In order for the water in the reservoir to be always clean and fresh, it must be changed periodically. The design turns out to be quite high, so manually draining water from it is inconvenient and difficult.

To automate the process, it is recommended to make a drain system in the lower side of the wheel. To do this, you need to prepare a small hole at the bottom of the tire, insert a pipe with a tap into it and fix it with a lock nut and washer. How to make a do-it-yourself pool drain system from a wheel can be seen in the photo.

How to improve the pond outside

Possible options decoration - paint outer part tires with multi-colored paints or lay out a wall around it from natural stones. The base around the structure can be overlaid paving slabs, plant flower beds, sow lawn grass and break up the lawn.

As you can see, you can make a pond with your own hands almost for free. One has only to apply a little ingenuity and imagination - and your country house will have a great place for swimming, which is a great alternative to expensive stationary structures.

The pool in the country is gradually becoming an indispensable part of the interior and an essential condition for a comfortable stay. It's so great sometimes to plunge into cool water after putting things in order in the beds and in the garden!

A tire pool can be a great alternative to an inflatable pool in the country, as it is more reliable and durable.

If you like to do it yourself, we offer a practical and low-cost option - a tire pool.

This design can last much longer than an inflatable pool, which must be handled very carefully. And if you also connect all family members to the creation process, then this lesson will be very entertaining.

How to create a home pool from a tractor wheel?

In order to equip your site with a small pool, you will need the following accessories:

a large wheel, for example from a tractor or KamAZ;
sand and gravel;
cement;
sharp large knife or jigsaw.

So, let's start creating a pool from a wheel:

It all starts with tire processing. It is necessary to cut one of the sides so that the end result is only a side. In order to cut the cord, you can use a hacksaw. It is not recommended to use a grinder, since during its operation the rubber will not only fly apart, but will also become very sticky, and it will be extremely difficult to get rid of it.
The next step is to install the pool. To build a fixed pool, you need to prepare a site for it. First, the turf is removed on the bayonet, equal in area to the tire. If you plan to make a concrete path to the pool, then you should increase the perimeter, as you will need to increase the fill radius. After that, a small sand cushion is made.
The next step is concreting. It is necessary to mix the cement mortar with which the prepared circle will be filled. A tire is installed in the concrete that has not yet hardened. The next step is to level the cement. Looking into the tire, where the rim was previously, you need to pay attention to whether the solution goes beyond the edges or not. If not, then you need to add a couple more buckets of cement. This is done in order to create tightness.

After that, level the bottom and leave the structure to dry. To protect the future pool from possible bad weather, you can cover it with a film. If the structure is erected on a sunny site, due to exposure to sunlight, moisture will evaporate and settle on the surface of the tent. Therefore, from time to time, the protection should be removed and the space ventilated so that the cement dries efficiently.

Once the bottom is dry, you can start decorating the pool. We will leave this item free for your imagination.

Thus, the construction of a pool from a tire will take no more than an hour.

In order for the pool to serve its owners with benefit, you should pay attention to a few recommendations of homemade masters:

If desired, you can create a transportable pool. For this purpose, a plywood circle is cut out under the existing tire, two medium-length bolts are screwed into it in the place where the rim will be. They will serve as a mount for the cement plug. After that, a tire is laid on the workpiece and poured with cement. After it dries, the pool is ready for use. Transportation will be easier if the legs are adjusted to the bottom of the structure.
For stationary pools, it is better to choose a place as dry as possible. Otherwise, before creating a sand cushion, it is necessary to lay a layer of gravel, while the cement layer will be slightly increased. If this is neglected, cracks will appear in the cement base very soon and the water will not hold for a long time.
It is better to paint the tire before pouring. But keep in mind that water heats up much faster in black tires, as this color attracts heat well.

As for changing the water, this issue should be addressed even before you pour the concrete. You can install the valve with two washers and a lock nut. Such a device will not leak, as the compressed rubber provides tightness.

It is advisable to change the water in the pool every 2-3 days. This will reduce the risk of contracting any infection.

The decorative tire pool is not intended for swimming, but it decorates the interior of the garden.

At your dacha, you can also create a decorative pool, which will play the role of a small pond. In addition to stones and algae, you can launch several fish into it.

For such purposes, you can also use a large tire from large vehicles. You will need gravel, concrete-cement mortar, bitumen or ordinary film, vegetable soil.

The process has the following sequence:

First of all, you should prepare a pit. Its diameter should be 20-30 cm larger than the existing tire, and the depth of the pit should be equal to 2/3 of its width. The base bottom should be well leveled.
Then a layer of gravel is poured to the bottom and carefully compacted, after which it is concreted.
After that, the bitumen is melted and the bottom is poured with it until the substance reaches the tire bead. Thus, waterproofing is created. Instead of bitumen, you can cover the bottom with a film. It must be carefully straightened along the bottom, and the edges bent outward.
The space that forms between the tire and the walls of the pit must be tightly covered with soil and this piece of land must be compressed.

If there is a desire to increase the area of \u200b\u200bsuch a pond, then you can also remove the upper part of the tire, which is bent inward.

Such a decorative pool is decorated with stones, flowers and other garden attributes. Now you can fill in the water and run the fish.

This decoration will look great on small plot, and over a large area. But the main thing is to remember that even such small reservoirs require care. Therefore, the water must be periodically changed, and the bottom of the pool cleaned.

Creating a pool or ornamental pond from a tire will not only take you a little time, but it will also bring great pleasure from the fact that you made it yourself.

The choice of blank largely depends on the place that you can allocate on your site for this decorative "highlight". Not enough space - a tire from a passenger car, more space - good:

KAMAZ tires;
rear wheels of the tractor "Belarus";
tire from a 45-ton "BELAZ".

Used tires can be found in a tire shop (free of charge) or at a car company (for symbolic money). An offer of a product of this kind can be found on the Internet.

What kind of pond can be built?

Of course, in such a pond it will not be possible to breed fish, but land water lilies, marsh turkey and floating pondweed, and along the banks - Siberian iris, it is quite real.

With a decorative flagstone, you can hide the rubber base, break an alpine hill next to it - and no one will guess about the fundamental principle of your decorative pond.

Photo of mini-reservoirs from tires with your own hands, which you can do in the country with your own hands.

Even such a non-standard pond may be a source of danger to children left unattended.

What will the craftsman need in the course of work?

Tool:

shovels (bayonet and shovel);
building level;
hacksaw or jigsaw.

Consumables:

sand;
crushed stone;
stones;
soft sealant;
plants for decoration.

Video about creating an artificial pond from a car tire with your own hands.

How to move towards the result, having the right tire on hand?

How to make a decorative mini-pond from old tire with your own hands? Step by step instructions with photos:

on the surface of the leveled area;
buried in the ground by a third;
buried in the ground for the entire width of the treads.

Digging a hole in the form of a tire, a size slightly larger than its outer diameter. We determine the depth based on the previous paragraph.

Level the bottom and fill it with sand(15 cm).

We lay the tire on the compacted bottom of the pit.

As a soft sealant PVC film can also be used, but a special covering material for pools is preferable, which is easy to purchase in specialized stores. It is freely spread along the bottom of the pit and the edges are brought out (half a meter beyond the limits of the tire laid in it).

In order for the film membrane to be rationally distributed inside the tire, water is poured and carefully straighten the covering material. To fix it, you can use rounded stones, laying them on the bottom at opposite ends.

The edges of the film material, brought out of the tire, must be straightened and covered with sand to hold, then decorate gravel, wild flagstone or turf laid on powdered soil.

At this stage of work, the "newborn" pond can be revive the fountain, for which a small pump or turbine for an aquarium with a nozzle is suitable. For the operation of such a fountain, an electrical connection is needed. For safety, it is fashionable to put the wire in a plastic hose and dig it in.

Another video on how to make a pond with a tire fountain.

An interesting addition would be garden lamp lighting on solar batteries. During the day, it accumulates energy, and in the evening it gives soft light.

If the bottom of a man-made reservoir is camouflaged with gravel or sand, the water will become cloudy.
So that small animals living in the garden do not accidentally die in the pond, you can place a picturesque snag in it, along which they can get out of the water.

Options for decorative solutions for a tire pond

It is possible to build from different-sized or equal-sized tires two ponds contacting protectors. In the process of decorative design above the junction, according to Russian tradition, install a bridge from birch logs unpeeled from the bark - a beam bridge. The bridge can be a plank, and even with a railing. It can be purely decorative or part of a garden path.
If one tire is installed in a recess, and the other on the surface of the site, you can get two ponds with overflow. An overflow can provide rainwater drainage from the roof or a homemade waterfall.

You can make it by bringing it to the upper pond, through the thickness of decorative heaps of stone, a thin hose with a weak water pressure. The flow of water, which will fall from the height of the stones, will provide overflow to the lower pool.

Swimming pool from a small tire can even be used to decorate a balcony, loggia, terrace. In this case, the side surface of the tire is pasted over (on a waterproof basis) with an artificial stone.
A large tire will allow you to create paddling pool for children. To do this, you need to strengthen the tire as best as possible, preventing possible shifts, and securely tile the coastal zone with tiles to ensure the safety of walking barefoot. In addition, you will need a pump to filter the water, or replace it periodically.

Photo of finished ponds in the country or a plot of the house with your own hands from tires.

If you have a desire to bring beauty into the usual order of your garden and you have a used tire at hand, hurry up, and a decorative pond surrounded by unusual plants can decorate your garden already this season.