DIY homemade from improvised. DIY crafts from improvised means at home. Collection of handmade stamps

Crafts made from old items and things that can be given a second life can make your home much more comfortable. Some do-it-yourself homemade crafts for the household can significantly save the home budget, make work easier, or make the surrounding interior more interesting. And even if difficulties arise in the process, overcoming them will be worth it.

DIY for the home workshop

In almost any home there is always some set of tools necessary for the household. But sometimes situations arise when working in your own workshop or garage requires some kind of device that is either impossible to purchase in a store or is very expensive. In this case, the way out can be found by making it yourself.

Blacksmith's forge from a cylinder

This device for heating metal will become an indispensable assistant in the home workshop. The forge can be safely used to make original items using artistic forging. These will be truly unique forged items.

For the bugle, it is best to use an empty gas cylinder with a capacity of 25 liters. Its ends are cut off by a grinder, and the hearth door and its back will be made from the cut parts. Inner part the cylinder is covered with refractory ceramic wool, which is able to withstand temperatures of more than 1200 0 C. From above it is coated with fireclay (lined), which can withstand temperatures up to 1500 0 C. Fireclay slabs or refractory bricks are laid on the bottom of the hearth after lining.

A hole is drilled from above and a small drive is inserted, which allows inserting the nozzle of a gas-powered burner, which can create a temperature of more than 1000 0 C in the furnace - quite sufficient to heat the metal to a certain temperature suitable for forging.

Collapsible garage crane beam

In the manufacture of such a lift, the cash costs will be much less than buying a factory model. For its manufacture, you will have to spend money only on materials, half of which, perhaps, can be found in the garage.

Materials needed to assemble the lift:

1. Two racks - a profile pipe 100x100x2350.
2. Cross bar - steel pipe arbitrary length with a diameter of 100 mm.
3. Four supports for the rod - profile pipe 100x100x600.
4. The basis and braces - a corner with regiments on 100 mm.
5. Two metal rollers for the cable.
6. Four wheels for movement.

For the lifting mechanism, it is best to use a worm gear hand winch with maximum load up to 500 kg, which is attached to one of the racks of the crane beam.

The design does not take up much space in the workshop, moves easily on hard surfaces and is quite convenient for removing the engine from the car.

Mobile tool rack

The main highlight of this rack is its small size., but at the same time it is possible to place a large number of tools, and if necessary - quickly move it to any place or adjacent room. It is very convenient to use such a rack in your workshop or when conducting construction and repair work in large rooms, especially when you need to frequently move tools.

The rack can be assembled on the basis of a collapsible plastic rack mounted on a self-made platform with wheels (trolley). The platform is made exactly to the dimensions of the rack from a metal corner with shelves 45x45 mm or a sheet of plywood with a thickness of at least 10 mm. For movement, furniture metal wheels are used.

Additionally, it is possible to make and fix fasteners for building levels, extension cords and other tools that can be stored in a hanging position to the rack.

Help for the hostess

There is not always a financial opportunity to buy, for example, something from new furniture in a furniture store or place an order for its manufacture. But you can always get out of this situation by making the right thing with your own hands, while making it attractive and unique, using improvised means for this.

Cork kitchen apron

A kitchen apron is a wall surface located between the countertop and wall cabinets. Usually this part of the wall is lined with tiles. But many other materials can be used to cover it, for example, wine corks can be glued to the wall.

Such an exclusive decor looks quite great.

Before sticking, each cork is cut lengthwise into two halves with a sharp clerical knife. It is desirable to paint the wall black, which will emphasize the seams between the plugs.

Corks are glued to the wall using liquid nails in a checkerboard pattern or with a certain pattern, since it is unlikely that they will be laid out perfectly evenly, and curved rows will visually look disgusting.

The corks themselves are not afraid of moisture, but they quickly get dirty and are poorly washed, so it is best to close them with a tempered glass screen. True, you will have to spend a little money on it and order glass in a special workshop, where they will cut it to a given size and make holes for sockets and fasteners.

Glass is fixed to the wall with anchor dowels, which can be purchased at almost any hardware store.

Although an apron decorated with wine corks can be expensive, the result will be worth it.

The surface of the countertop, as well as the wall, can be decorated with corks and covered with tempered glass.

Hinged folding table

A folding table fixed to the wall allows you to save some space in the apartment. In the folded state, it can protrude from the wall at a distance of no more than 10 cm and does not interfere with anyone at all, but when unfolded, it can replace a full-fledged table.

There are many options where you can use a folding table fixed to the wall. Here are just a few of the most basic ones:

Shower for giving

There is probably nothing better than refreshing yourself under running water on a hot summer day, especially if he was working in the garden. Naturally, only a shower will solve this problem and relieve the fatigue that has accumulated during the day.

The shower can be installed independently without outside help, the main thing is to choose a place for it and decide on the type of shower cabin.

Three types of cabins stand out among summer showers, which you can freely build on your own:

Installation of a simple shower is done in this way:

1. A shower cabin frame is being made, which can be assembled from metal, wooden beam or other improvised materials.
2. A metal or plastic water tank is installed on the roof of the assembled frame, which can be from 50 to 200 liters in volume.
3. It is advisable to paint a metal container black for better heating of the water. Additionally, several electric heating elements can be installed in the container, then you can take a shower even in cloudy weather.

The booth can be sheathed with boards, plywood, slate, or simply covered with a tarpaulin or cellophane film with folding canopies.

To build on your own

The topic of construction or repair, probably, worries everyone. And, of course, everyone who deals with it wants to finish it as soon as possible with minimal financial costs. Therefore, if you want to save money, you can make some materials for construction on your own. For example, it can be wall SIP panels or such useful tool, like a vibrating plate, the need for which often arises among many owners of a personal plot.

Homemade SIP panels

For their manufacture, you need to prepare a flat, hard platform. After laying a sheet of OSB 10-12 mm thick on it with a rubber spatula with teeth, apply glue to it.

Then lay sheets of foam grade 25-30 on the glue. After that, an adhesive mass is applied on top of the laid foam, as well as on the bottom OSB plate, and the second sheet of OSB is laid on top.

If several stacked boards are being made at the same time, work should be done quickly until the adhesive has set. Usually in this way you can prepare no more than 4-5 panels at a time.

After harvesting, the formed slabs need to be pressurized with a press. Since at home, of course, hydraulic press no, it can be replaced with a thick plywood sheet laid on prepared SIP boards over the entire plane and loaded for 2-3 hours, for example, with several bags of cement, sand or other cargo. You can even use a car by driving onto a plywood sheet along a pre-made flyover.

After the glue has completely dried, the home-made panels are ready, they can be folded into a separate pile and proceed to the preparation of new panels. The manufactured panels should lie unloaded for another day, after which they can be used for their intended purpose.

Vibrating plate manufacturing

To make a homemade vibrating plate, you will need to prepare:

1. An electric motor with an eccentric brand IV-98E, which is the main part of the vibrating plate.
2. Steel sheet, at least 8 mm thick, 450x800 mm in size. It can be ordered at any metal base.
3. Two pieces of channel no more than 400 mm long.
4. An inch pipe for the handle and two rubber bushings for attaching it.
5. Of the tools you will need a welding machine, a grinder and a set of wrenches.

From the narrow sides of the plate, stepping back from the edges by 80-100 mm, make an incision with a grinder to a depth of about 5 mm. After that, bend the edges towards the notch at an angle of approximately 25 0 and weld them by welding. Bends are needed so that the vibrating plate does not sink into the material compacted by it and moves freely along its surface.

Then, across the plate at a certain distance, calculated for mounting the electric motor, two channels are welded with the shelves down. Through advance drilled holes in the channel, with the help of M10 bolts, an electric vibrator is attached to them.

The tube handle is attached to the vibrator via soft rubber grommets, which can be purchased at an auto parts store or hardware store in the hardware department.

Thus, you can make a lot of useful things in the household with your own hands, spending on this only a part of the money that you would have to pay when buying a finished product. You just need to make some effort and have certain skills.

According to the results of many experiments, it can be seen that hand-made production of unique and non-standard souvenirs is a very exciting and interesting work. It promotes the development of flexible thinking, creative taste and aesthetic imagination.

Participation in such a cognitive process is within the power of even small children, because making crafts from improvised means with their own hands takes even not assiduous and not very obedient children for a long time.

For the manufacture of any materials of natural and artificial origin. After all, improvised raw materials are always available and do not require any waste.

And the masterpieces that are made from materials that are no longer needed or not suitable are fully competitive with store counterparts, since they have no analogues. Such products will organically fit into any interior, which will add to it exquisite originality.

What crafts can be made from improvised means

• various photo frames;
• coasters for hot cups;
• many different toys;
• decorations for every taste and color;
• key holders;
• original quilling souvenirs;
• different candlesticks;
• crafts for flower beds and garden plot;
• designer suits and dresses for matinees;
• playground design for children;
• graceful decorative flowers;
• interesting decorations;
• and many other various design masterpieces.

To make it easier to make souvenirs with my own hands, photos of improvised crafts that can be found on the worldwide web will help with this. No need to copy, you just need to understand the technique of work and do something of your own.

By the same principle that postcards are made, it is possible to make a bright panel from paper and cardboard. But in this case, in order for the souvenir to look complete, you also need to think about a frame that can be made from various materials.

Instructions for crafts from improvised means

Let's take a closer look at the example of crafts from plastic bags - a kite, which the kids like so much. For manufacturing, you need to prepare:

• 2 bags with polyethylene;
• 2 skewers;
• Scotch;
• black marker;
• scissors;
• fishing line, which can be seen with strong threads.

The process of creating a masterpiece:

Straighten the bag and put skewers on it, as if in a cross, but the longitudinal should be a third higher, from the middle. Now, with the help of a marker, you need to draw lines that connect the ends of the skewers.

Then, it is advisable to cut out the figure that turned out. Tape the skewers to the bag with adhesive tape.

From the second plastic bag, you need to cut a piece, 4-5 cm wide, of any length - for the snake's tail. It is possible to make a tail from several short pieces of packages, having previously combined them with tape. After that, you should tie the tail to the lower half of the flying kite.

At the end, you need to make a hole in the place where the skewers cross, and securely tie the fishing line there. Ready!

Step by step crafts for beginners

To make crafts - a goose from kinder eggs, you will need:

• yellow testicles from kinders;
• buttons: 1 for the nose, 1 for the tail and 2 for the eyes;
• ribbon;
• awl;
• elastic thread;
• glue.

The process of creating a masterpiece:

With a preheated awl, all the eggs are pierced, one opposite hole.

Then an elastic band is threaded from the tail to the head. Next, you need to put on a button-nose and thread the elastic in the opposite direction, through another hole.

Since both ends of the thread appear in the tail, it is advisable to secure them using a button. Now you need to glue the eyes and strengthen the button on the tail of the caterpillars. In this way, it is possible to manufacture a whole family of similar caterpillars.

Master classes on crafts from improvised means

For a cardboard Christmas tree, you need to prepare:

• cardboard;
• glue;
• Scotch;
• paints, felt-tip pens, pencils;
• scissors;
• glitter, stickers, or something else - for decorations.

The process of creating a masterpiece:

Cardboard must be folded in half and cut where it folds. The halves that came out are folded in half again.

On one particle, on the opposite side of the fold, half of the Christmas tree is drawn.

The sheets are folded together and cut along the drawn line; so two identical Christmas trees are obtained. Then you need to secretly mark the middle of both Christmas trees.

On one Christmas tree, an incision is made from the top to the middle along the midline, and on the second, from the bottom to the middle. Now, it is advisable to insert the Christmas trees into the cuts, and you get one lush Christmas tree.

For greater stability of the Christmas tree, adhesive tape is used - both halves are glued together with it.

To decorate the Christmas tree, pencils, felt-tip pens, sparkles, paints, etc. are used. At this stage, everything that only the imagination suggests is done.

Conclusion

Every parent who loves his child sooner or later thinks that it is useful for a child to do at least something with his own little hands.

Indeed, in the life of children, more and more space is occupied by gadgets, and real exciting activities have a much higher value. That's why making crafts from improvised means will become perfect activity for kids and adults.

Photo crafts from improvised means

Someone will certainly take a look at this collection of ideas and say what is easier to buy new furniture or decor. But this article is not for them, but only for true connoisseurs of the unique style and products. handmade. Here you will find the 10 most beautiful interior items that you can do for your home without spending extra money.

The best crafts for the home with your own hands from improvised materials for 2018!

1. Decoupage and other do-it-yourself furniture repair ideas

Restoration of old chests of drawers and sideboards is perhaps one of the main trends of our time. Many pieces of furniture fail over time: tables and chairs loosen their bodies, upholstered furniture is pressed through and requires a new “stuffing”. But chests of drawers and sideboards can stand for themselves long years and bother you with their outdated appearance.

Home needleworkers and decoupage masters have not only found a way to update the design old furniture, but also raised the fashion for the use of vintage "grandmother's" chests of drawers in the interior. Detailed instructions on painting and decoupage you will find in our article .

Below are some photos of amazing home projects to inspire you.

Restoration of an old chest of drawers with replacement handles and hand painting:
Painting and finishing an old cabinet with metal buttons:
As a result, the furniture acquired an original Moroccan-style decor effect. Simple, like all ingenious:

By the way, in this way you can create more sophisticated things for the home:

Decoupage and painting amazingly transform old furniture facades, but not every person has enough time and patience for this painstaking task. Therefore, the best DIY home ideas also include refurbishing furniture with duct tape in marble, gold, and other unusual finishes. A minimum of effort - and the most ordinary piece of furniture will turn into the main decoration of your interior.

2. Beautiful things for the home with your own hands: carpets

Perhaps the most pleasant thing about creating things for the home with your own hands is when one of the guests asks: where did you get such beauty? A stylish rug with a zebra print (or other motif of your choice) will certainly deserve such a compliment. And not once.

The fabric can be any. The main thing is that it should not be too demanding in care: it is not afraid of moisture and is easy to clean. In this case, the master chose the vinyl fabric. It is heavy and strong enough to look like a true carpet. What's more, the quality of vinyl these days is very impressive, and it's available in a wide variety of colors and interesting textures.

Everything necessary materials and tools:

• Thick paper;
• Vinyl upholstery;
• Scissors;
• 2 Krylon pens or regular fabric paint.

Procedure:

1. Create a paper stencil. Draw and cut out the outline of the zebra skin, then the drawing itself on it. Do not worry about your artistic talent - the skin of a zebra and should not look uniform or symmetrical. In extreme cases, the pattern can be copied from a picture on the Internet or even printed out to cut out.
2. Attach the stencil to the vinyl fabric and outline the stripes with Krylon pens (spray or brush). After that, the stencil can be removed and continue to paint the areas inside the contours.
3. Let the paint dry and you're done! To be sure the pattern will hold, you can "seal" the carpet by spraying a clear coat of acrylic spray paint over it.

Krylon handles create a stunning gold leaf effect on the surface of the fabric. In addition, the paint in them dries quickly and is very securely held. If you can’t buy them in your city, then use regular fabric or wall paint. As the next hero of our article.

He took a cheap white rug as a basis and decided to give it an interesting look with his own hands using a chevron pattern. All he needed was thin duct tape, scissors, a thick brush, and two different shades of latex paint.

Finally, another inspiring example where a makeshift stamp is used instead of a stencil. The craftsman had a rubber bath mat, leftover wall paint (which had been slightly thinned with water for a vintage effect), a roller and an old IKEA wool rug. We look at the photo that he managed to cook from these ingredients.

3. Unusual "marble" DIY crafts (photo)

7. Turn photos into wall decor

This is much cooler than just hanging photos in frames! Your personal photos or any images you like from the internet can turn into beautiful wall art for any room. To make such a decor with your own hands, you can use any of the following methods.

1. Find or buy a substrate. A thick sheet of polystyrene foam or polystyrene foam can act as it (as in this case), board and other improvised materials.
2. Print the photo, having previously edited its dimensions so that they are about 5 cm larger than the substrate. These "extra" centimeters will go to the folds.
3. Cut the photo and backing into pieces if you want a modular set rather than the whole picture. Otherwise, skip this item.
4. Overlay the photo on the substrate and wrap the ends. The author of this product used double-sided adhesive tape to secure the photos. You can mount with ordinary glue or other available means. The very surface of the photographs can also be treated with glue or gloss paste.

1. Print the image and prepare the canvas to which it will be transferred.
2. Pull the canvas over the frame and apply a thick layer of medium gel on it. These gels are widely available and today you can buy them in any store of finishing materials.
3. Place the photo on the oiled canvas and press down. Leave it like this for several hours, but periodically sprinkle with water from a spray bottle.
4. Carefully, use your fingertips to start erasing the back of the image from the canvas. Remove all paper in this way.

As a result, you will get a beautiful one with scuffs that will only give it a touch of vintage style. It remains only to apply the last layer of medium gel on it as a protective coating.

For inspiration, here are a couple more ways to decorate your interior with a photo.

We apply the old window frame as a photo frame. How do you like the idea?

8. Creative homemade lampshades for lamps

Homemade lampshades made of fabric, paper, thread and other improvised means will not only decorate your home, but also bring an unusual atmosphere into it every dark time of the day.

Look for the best ideas for your taste in our article . The next photo shows a popular creative thread lampshade.

9. Succulents - do-it-yourself living home decor

A succulent living wall is perhaps the most amazing DIY craft you can make for your home. Agree: if you saw it in someone's design of a living room or another room, you would not be able to remain indifferent!

Dekorin will tell you how to get such an impressive and sustainable decor:

1. You will need a shallow wooden container for planting and a metal mesh.
2. To fix the mesh on the container, use an impromptu wooden frame, which can be made from small boards or chips. Attach to staples or nails.
3. Prepare any for composition. They easily take root in the most difficult conditions and look best when you combine different shades and shapes of leaves. Common examples of succulents: aloe, various cacti, young or stone rose (Sempervivum), stonecrop (Sedum), mountain grate (Orostachys), etc.
4. Fill the container with soil and plant your chosen plants in it. Use any cactus mix for drainage.

Here are examples of crafts for the home that you can do with your own hands using the above method.

10. Crafts for the house with your own hands from glass containers

Glass bottles and jars often accumulate on balconies and in pantries. What they just don’t turn into today: lamps, candlesticks, vases, table decor ... It’s amazing how easily they become part of a stylish interior, you just need to use a little ingenuity, as well as paints, fabrics, threads, paper and other improvised means. Last batch of photos for today. Also read:

10 best ideas what you can do at home with your own hands updated: March 21, 2018 by: Margarita Glushko

There are different ones, some are made of paper, others are made of wood, and still others are made of both, and even with the addition of a third. This section contains exactly those that are commonly called the simplest, they are the result of the simplest actions and do not require serious professional skills and knowledge. Although it is immediately worth noting that not everything is as simple as it seems. Therefore, even when making the simplest crafts it is important not to relax and clearly follow all the instructions that are presented in our articles. In more detail, this section contains information on the manufacture of simple homemade products from paper, clay, matches, plastic bottles, cans and from many other commonly available materials. By the way, we even have an article about how to become a house general and a vampire. It is important to note that almost all of this section does not involve spending money. Here you can find many options for making various children's crafts, as well as crafts for Everyday life, for example, key rings. In addition, here you can find the option of making a gift for your family or friends, and especially for a child. Everyone can do what is presented here, so you need to start with the manufacture of homemade products that are in this section.

Astronomy is a very rare hobby that is not suitable for everyone. But everyone wants to watch the stars and the moon. But if you have a growing child and also very inquisitive, then the best gift there will be a telescope.

Apple iPhone 6 16 Gb is an iPhone with a completely redesigned design compared to previous generations. A fundamentally different approach! Miniature gadgets that are easy to operate with one hand have been replaced by a smartphone with increased dimensions (height 138.1 mm, width 67 mm), which will have to...

Cross-stitch is a popular activity for many needlewomen. The process itself is quite simple, does not require large expenditures, and also has a good effect on nervous system. The result of such work is always pleasing to the eye ....

Sewing machine often becomes the center of family comfort. Housewives, even stylists, and all those who aspire to make their own small family business out of sewing spend a lot of time behind it....

Interesting homemade for giving are waiting for you in this article. You will learn how to make a lawn mower from an old washing machine, make a sink, a country shower, a dryer from improvised materials.

Useful homemade products for giving - do-it-yourself washing

Not everyone has the financial ability to buy a Karcher car. If you can't buy it, why not invent it? A home-made car wash will allow you to do without running water, reduce water consumption and thoroughly wash the car, fence, garden path or other items.

Here's what you need for such a homemade to give:

• plastic canister with a capacity of 5–20 l;
• hose connector kit;
• automobile nipple;
• piece of hose;
• silicone sealant;
• sharp knife;
• compressor or car pump;
• irrigation gun.

Take a set of hose nozzles, which includes 2 connectors, a 3/4 threaded fitting, a 1/2 adapter.

Here is the principle of operation of such a homemade product for giving: you connect the gun to the hose, attach this device to the bottom of the canister. A nipple will be built into its neck.

Fill the container with water, but not to the top. Then screw on the lid and pump air in. This will create pressure, and the water will run well when you start to pull the trigger of the gun. Here's how to assemble such a mini sink.

Carefully cut a hole in the lid with the tip of a knife. It should be slightly smaller than the diameter of the nipple stem. Also cut a circle of the desired diameter at the bottom of the sidewall of the canister.

Insert the nipple into the cap.

Now, helping yourself with the wire, place the coupling in the hole intended for it. Apply silicone sealant to secure the coupling to the canister.

It is necessary to tighten the cover and carry out other work only after the sealant has completely cured. Then you will connect one end of the hose to the water gun and the other to the canister.

Pour water into the container, but not to the top so that there is room for pumping air. But do not pump too hard, so that the canister does not deform and burst under pressure. See how the fitting should be screwed in and the connectors installed.

If everything is done correctly, then when you press the trigger of the water gun, the water will spurt out in a good stream. You can adjust the pressure by twisting the tip of the gun.

In the country, it is hardly possible to do without a shower. Try to make something unusual, but tropical, then you can enjoy even more water treatments.

How to make a rain shower from improvised materials for a summer residence?

If you have only recently acquired a plot and you do not yet have a washing room, then you can take a shower right on the street, enclosing a small area near the fence with a curtain. To make such rain shower, very few components are required, these are:

• bracket;
• wire;
• flexible hose;
• metal beer can;
• hose adapter;
• awl;
• nails.

Nail the metal bracket onto the wooden fence to get the fixture at the right height. Screw the adapter to the tip of the hose, fix it on the slot of the beer can. The joint can be treated with a sealant. Using an awl, make many small punctures in the jar.

Tie the top of the hose to the bracket with wire, and attach the other end to a water pipe or pump. When you lower the pump into a barrel of heated water, you will be able to take pleasant water procedures.

You can also make a rain shower head using a disc container. In its center, you need to fix the plastic adapter that is attached to the shower hose, and the central axis of the discs must be removed. Using an awl, make holes at the top of the lid. Glue all fasteners well with sealant. Such a nozzle is held on the bracket with a thick wire or on a rigid pipe.

If you have a desire to make a rain shower, then you can use plastic pipes for this.

You need to bring water to them, first make a lot of small holes with a soldering iron, and then enjoy the pouring drops. Children really like such water procedures.

But do not forget to first check the water in the container from which it will be poured into the shower, it should warm up in the sun.

And to make a stationary shower, you must first pour water into a tank or barrel, which will be located under the roof or on the roof of the building. On a warm summer day, the water here warms up well, and you can wash yourself plenty. To be able to do this in cooler weather, then it is necessary to provide a heating system in such containers.

Do-it-yourself country shower

Before installing it, you need to make a shower cabin. If possible, you can make it out of wood by placing this small structure on the base. Put wooden door or limit yourself to this shower curtain.

There are more simple options. If you have oilcloth, then use it.

Another option is to purchase impregnated fabric or use an old awning or tent.

If you made a fence from corrugated board and you still have materials, then try to make a shower for giving from them. Metal pipes need to be dug in according to the markup, poured with concrete. When it dries, cut sheets of corrugated board are welded to the racks. One of them will become the roof.

If you have little wooden planks, then implement the option shown in the next photo on the right. And on the left is a shower, which is made like a wattle fence. So the materials for it will cost almost free.

When the shower is ready, you can install a water tank on it. To make it warm up better, you can make a kind of metal or hose coil. Then the water will warm up more actively.

These and other homemade products for giving allow you to make the most of the available containers.

To be able to get warm water even when it is not heated by the sun, use electric heating. To do this, you can position the plastic barrel vertically or horizontally. Then it will be necessary to mount the ten on one side, and on the other? water inlet fitting. Make an overflow hole so that excess liquid flows out, and you can see that the container is already full.

Now it remains to install the tank. Usually, a shower roof is used for this. You can put a flat tank here, made of iron or plastic. You can also make a soul canister from a metal or iron barrel. If you need to heat the water, then a heating element is mounted in the barrel.

Check out other examples of what can be done on personal plot with your own hands.

Interesting homemade products for giving with your own hands

Garden tools are very necessary for working on the ground. Often in the store they sell not very high-quality sets. After a short use, the handle of the shovel breaks off, or the teeth of the chopper are bent. Therefore, if possible, try to make tools with your own hands.

Take:

• cutting;
• fragment of a water pipe;
• scrap from a two-handed saw;
• screws;
• screws;
• fragment profile pipe section 3 cm.

Using a grinder, cut a piece of pipe. Taking a lever tool, you need to cut a piece of pipe, unbend the sector, and in the place where the stalk will be, you need to work with a hammer to give the future chopper the desired shape.

To make a blade, take a piece of a two-handed saw and draw the outlines of a future chopper. Punch two holes.

At the same distance and the same diameter, you need to make 2 holes on the chopper itself, and then cut out a fragment from a two-handed saw.

Drill these holes with a drill and a drill designed for metal work. Connect these two parts with rivets, which are screws.

Now drill a hole in the top of the chopper to attach the handle here.

Make also a scoop, which is very interesting to work in the beds. Then such homemade products for giving will allow you to get a very durable set of tools.

Saw off the desired piece of the handle with a grinder and begin to unbend its part with a chisel.

Then, helping yourself with lever tools, straighten this part almost completely.

It remains to work with a hammer so that the scoop blade acquires the desired shape. Using a felt-tip pen, draw the outlines of its working part and cut it out with a grinder.

Using an abrasive wheel, clean the edges of the shovel and make them more even. Now process the tool with an emery petal wheel. That's how shiny this shovel will become.

Also drill a hole in it for the handle, then insert it and secure with a screw.

Cover the cuttings of both tools with an antiseptic, and then with varnish. Now you can use the tools for their intended purpose. If you want, follow the same principle to make a cultivator for beds.

It is very exciting to create such things for giving with your own hands. Maybe after you make the tools, you will want to make a device on which you can dry part of the harvest. See how one gardener did it.

How to make a dryer for fruits and vegetables?

See what materials you need to take for this:

• sheet metal;
• square pipes;
• locking mechanism;
• polycarbonate sheet;
• self-tapping screws, screws;
• 2 door hinges.

But what tools you need to arm yourself with:

• grinder;
• welding machine;
• drill;
• stationery knife;
• tape measure and marker;
• scissors for metal;
• hacksaw.

First you need to make the basis for the drying cabinet. Make a frame from square pipes. Horizontal and vertical racks sawed off so that the edges are even. And the ends on the connecting elements should be beveled.

The door here will be metal. To make it, cut 4 fragments from an iron pipe and weld them into a rectangle. Then you need to sheathe this base with metal, using screws with nuts and self-tapping screws. If possible, weld a steel sheet. To make a mount for baking sheets, attach wooden blocks to the back of the frame. Take self-tapping screws for this. In this case, on each side there are 4 wooden blocks for 4 baking sheets.

An absorber is installed in the dryer. Take sheets of metal and paint it black. Use heat resistant paint. When it dries, put this blank on the bottom of the dryer.

For the absorber, take a thick aluminum or copper sheet, in extreme cases, steel. These materials conduct heat well.

Now you need to sheathe the dryer from the outside, make the roof transparent, made of polycarbonate. Then the sun's rays will penetrate well here. You can also use glass. Cover the ventilation windows with mosquito nets to keep insects out.

Attach hinges and a locking mechanism to the door. Fasten the door in place. See what a wonderful beautiful and roomy dryer turned out.

It remains to make the opposites. They must be breathable. First, knock together the frames from the bars, and then attach a metal mesh to them.

Now you can cut fruit and watch how your device will work. Put a thermometer in the dryer to monitor the temperature. It should be in the range of 50-55°C. At lower temperatures, cover the lower openings by placing a rag here.

In such a home-made dryer, you can dry not only fruits, but also vegetables, herbs, fish, meat, roots.

If this diagram of the device of such a device seemed complicated to you, then you can make a dryer from a metal barrel. A hole for the door is cut out in it, and racks made of metal mesh are inserted inside.

So that water does not flow here and there is better ventilation, such a roof is installed on top.

You can upgrade this fixture with a fan and an electric heater inside.

If you want to make a lawn mower with your own hands, then this is also possible.

Turn an old washing machine into it, for example, like this one.

And if you still have an old bedside table, then you will make a platform out of it for a future almost self-propelled device. But you only need a door from the nightstand.

Drill holes in the center of the motor shaft. Make a cutting knife from an old two-handed saw. It is necessary to saw off from it to the size of the desired shape, cut a recess inside.

Attach two wooden pickets that will become the handles of the mower. Do not forget to fix the motor and extension cord to it. Now you can experience such an interesting unit.

If you are interested in other homemade products for giving, then it will be useful for you to watch the following video.

Lots of interesting ideas waiting for you in the first video.

A with cool homemade from plastic pipes you can get to know each other if you watch the second story.