home doors

Old interior doors as new - easy ways to update your own hands? How to restore interior doors? How to update old doors with your own

If you look with horror at your interior doors with peeling paint, no longer hiding imperfections with an adhesive film, chips and cracks, but the budget is painted to the penny, it's time to start restoration. It is this measure that will allow you to quickly and efficiently restore the canvas without resorting to buying new doors.

Usually made of plastic, glass, wood and its derivatives. And there are many different methods of restoration, but the most important stage is the cleaning and preparation of the canvas. It is important to carefully remove all traces of paint and varnish coatings, grease, old seals, align the canvas so that in the future the door looks like new.

Preparing a wooden door for restoration. Removing hardware and paint

The first thing to do is to carefully remove the door from its hinges and lay it on the floor or four stools.

Loops can be invisible, mortise, screw-in, removable and non-removable card. Since the entire door leaf will be restored, the hinges must be temporarily completely dismantled. To do this, unscrew all the bolts and caps, hook the door from below with a crowbar, lift it, remove it and set it aside.

In addition to the hinges, you should remove all other fittings that will interfere with further work.

Video - How to quickly remove the door from the hinges

How to remove paint. Method one - grinding

If the door is flat and there are a lot of layers of paint, you should take the canvas outside and try to clean it. grinder. The work is quite dusty, the grinding wheels clog quickly, but the result will not be long in coming.

Method two - the use of chemistry

On sale you can find various solvents and destroyers of old paint. One of them is B52. Principle of operation: surface wetting, waiting, cleaning of peeled coatings with a spatula.

In addition to the fact that this work is very difficult and harmful (solvent vapors are unsafe for health), it is worth noting that chemistry cannot cope with a large number of layers of the old coating. Therefore, this method is applicable only for cleaning small areas of the door with a thin layer of old paint.

You can make your own paint stripping mixture by mixing caustic soda, water and oat flour to a thick consistency. This slurry should be spread over the canvas, and after 30-50 minutes it should be cleaned off with a metal spatula along with the swollen paint layer.

It is important to use gloves and a respirator!

Method three - using a gas burner

For fire safety reasons, work must only be carried out outdoors. The paint heated by the burner comes off easily, but at the same time it can smoke and exude pungent odors.

This method is applicable only if you know how to handle the burner, have prepared a sufficient supply of cylinders and are ready to warn the neighbors about upcoming work.

Method four - using a building hair dryer

This method is the most productive and safe. Even if the layers of paint applied several decades ago are on the doors, they will easily peel off, and there will be no smells of burning or chemicals during operation.

Heat the paint and scrape off with a sharp spatula. Be careful not to damage the wood. Do not lean over the door as the air jet temperatures are around 600 degrees.

Method five - soft blasting

The method involves gentle, careful removal of complex dirt and old paintwork from metal, glass, wooden canvases. In this case, the door leaf will not be damaged. When working together with a jet of compressed air, Armex biodegradable cleaning agent will be applied to the surface of the door.

The main disadvantage of such a seemingly ideal method is the inability to perform work at home, the need to deliver the door to the workshop and the associated costs.

Method six - Using a drill and nozzle

The stores sell special abrasive brush heads that are worn on a drill. Metal fibers will remove old paint, but there is a chance of damage to the wood of the canvas. To process the entire door, you may need not one, but several interchangeable nozzles, the cost of which is 120-170 rubles apiece.

Video - Soft blasting

Puttying a wooden door

After all layers of old paint are removed, you should take sandpaper, fix it on the holder and carefully sand the door, making movements along the line of fibers. This measure will remove paint from hard-to-reach areas, smooth out scratches and chips.

After grinding, we vacuum the door and wipe it with white spirit, degreasing it.

Open a jar of primer, mix and apply the composition on the door with a thin layer. will extend the life of wood and serve as the basis for a new paintwork. Average consumption primers - 100 grams per 1 square meter canvases. average price packages weighing 2.5 kg - 280-350 rubles.

With a narrow spatula, we apply mixed putty for wood. Spread it out and let it dry. After that, you will have to once again process the entire door with fine-grained sandpaper to eliminate all the smallest defects.

If there is a large deep crack on the door, it can be eliminated by choosing a piece of wood that is suitable in size and color. We coat the sliver with carpentry glue and drive it tightly into the crack. After about a day, the glue will dry and the door will be ready for priming, puttying and painting.

Prices for popular types of putty

Putties

We strengthen the door

If your door has dried out from old age and is no longer strong enough, it is recommended to strengthen the canvas and the frame. And this must be done immediately after the preparation, but before the staining process.

If the canvas is deformed, a planer will help correct the geometry. We remove excess wood with a tool, simultaneously checking the accuracy of the corners with a joiner's metal square.

If the door dried out and closed very loosely, a large gap was visible between the canvas and the frame, it is necessary to cut a thin rail from plywood or board and nail it to the end face of the restored door. Then we process the rail with a file or planer, precisely adjusting the dimensions.

You can strengthen the door leaf with metal corners. But so that the door does not lose its attractiveness, you should pay attention to the decorative carved corners and install them (nail them with thin nails or fix them with self-tapping screws) after painting the canvas. Don't forget to buy a new one door handle, stylistically suitable for curly corners.

Replacing cracked glass

Cracked or simply outdated cloudy glass is not difficult to replace with your own hands. In its place, you can install a new one, for example, matte or transparent, tinted or sandblasted, embossed or smooth, colored or plain.

Note! If the glass has a thickness of 10 mm (triplex), then it is not advisable to replace it. Firstly, it is very expensive, and secondly, it is almost impossible for an inexperienced person to cope with such a task on his own.

Case 1. Glass is fixed with glazing beads

The easiest way to replace glass is fixed with glazing beads. It is enough to dismantle them, and then remove the glass with your hands. We arm ourselves with pliers and a metal spatula. We hook the bead with a spatula, and carefully pull out the carnations with pliers.

With a chisel or knife, we clean the glass bed. We make measurements. If the opening is non-standard, we make a figured pattern out of cardboard. At the same time, we take into account that the size of the glass should be slightly smaller than the opening. We wipe the glass with a soapy sponge, dry it with a clean rag, transfer the pattern from the pattern and cut it.

Attention! Use gloves to avoid cutting your hands. Perform work on a flat surface with a serviceable glass cutter.

We process the perimeter of the glass opening with sealant, after which we insert the cut piece, saw new glazing beads with a jigsaw and fasten them with thin carnations.

Case 2. Glass has a hidden fixation

If the glass has a hidden fixation, you will have to disassemble the door by unscrewing the bolts, removing the old glass and inserting a new one. Silicone cannot be used in this case, since it will not be possible to subsequently replace it. A significant disadvantage of replacing glass in such doors is that after assembly, the canvas may lose its geometry and will require editing with a planer.

By the way, instead of glass, you can use an acrylic shatterproof mirror. It is quite light, durable, highly decorative and easy to cut.

Learn about 10 the best options how to draw from our new article.

We paint the door

A door prepared in accordance with all the rules can be painted. We perform the work in two stages - applying the main layer of white paint and toning.

We choose a matte paint for wood, apply it with an airbrush or a brush, moving the brush along the fibers. We apply one layer, making sure that smudges do not appear.

Important! If there is a glass insert, then we must seal it with masking tape so as not to stain the surface with paint.

For toning, choose a glossy or matte paint of any color, for example, dark brown. We paint over the canvas in the same way. If necessary, apply another layer, but only after the previous one has dried. The more layers of paint, the more saturated the shade will be. But do not get carried away and create too thick a coating.

Important! Be sure to prepare and restore the door frame. Otherwise, the updated door will not contrast favorably with the wooden surfaces adjacent to it.

When the paint dries, you can apply a layer of glossy varnish or proceed with the installation of door handles.

Construction paint prices

Construction paint

Video - Do-it-yourself door restoration

Video - Master class on the restoration of an interior door with a glass insert. Glass replacement

You can restore not only wooden, but also. Before work, it is desirable to remove the canvas and lay it horizontally. This will make the job easier.

Step 1. We dismantle or cover with masking tape the door handle, peephole, and other fittings.

Step 2. With a metal brush or a drill with a nozzle, we clean off all traces of corrosion. We grind the surface with sandpaper (grain size 80-150). We vacuum the canvas and process it with a solvent.

Step 3. We process the door with car polish. It is not recommended to use wood fillers, as they do not adhere well to metal. The car polish will hide all the dents and micro-scratches formed after cleaning the rust. We smooth the applied polish with a spatula. The drying time of the composition is about 30-40 minutes.

Step 4. We polish the entire surface of the door with sandpaper with a grit of 400. We wipe the canvas with a clean, damp cloth, and then degrease it using a grease remover.

Step 5. We apply an anti-corrosion primer for metal to the door. In work it is convenient to use a roller and a narrow brush. After the primer layer has completely dried, re-grind the canvas with fine-grained sandpaper.

Step 6. Paint the door with metal paint. There may be several layers, but each subsequent one is applied only after the previous ones have dried. To apply paint, use a roller and brushes or an airbrush. Don't forget gloves and a respirator.

Similarly, we clean and paint the door frame, then remove the masking tape, mount the fittings and hang the door in its rightful place.

Thus, it is possible to restore not the entire surface of the door, but only a small area, but it is important to choose the tone-on-tone paint.

How to laminate an interior door with a film

For pasting doors, it is better not to use cheap PVC film, but to give preference to a durable “self-adhesive” D-C-FIX. Such a film is guaranteed to last more than 10 years, will not fade in the sun and will not rub.

The film is sold in rolls 45, 90 and 67.5 cm wide. The length of the roll is 15 m. The average retail price of this German film is 1,700 rubles. From a huge assortment, it is not difficult to choose an option with imitation of wood, stone, abstract or other pattern that suits a particular interior.

Glue the film should be carefully, enlisting someone's help. It is desirable to cut according to patterns, and immediately remove small bubbles with a wide plastic spatula. If the bubble does not go away, you can pierce it with a thin needle. For better plasticity, the film can be heated with a hairdryer.

Note! can be restored using glue-based veneer. We press the material to the canvas and heat it with an iron. We cut off the excess. We leave the restored door leaf for a while, pressing the pasted veneer with sandbags.

Prices for self-adhesive film

Self-adhesive film

Video - Pasting MDF with veneer

Video - How to glue D-C-FIX film

Video - The principle of gluing the film

How to replace door hinges. Photo instruction

We apply a loop, with an awl we outline tattoos under the drill, carefully cut the veneer with a blade

Video - Installing hinges on an interior door

The situation when interior doors become unusable and lose their appearance Not unusual. Knowing a few basic tricks on how to update old door, it will turn out to save a lot and not be spent ahead of time. Having learned how to restore the surface on your own, it will turn out not only to give the apartment a fresh look, but also to translate interesting author's ideas into reality.

By reading a few useful secrets below, you will be able to make repair work with your own hands. Do not forget about the importance of preparatory work, as this process also affects the beauty of the product. It will be possible to decorate the doors using paint, wallpaper, photo wallpaper, decoupage and other techniques.

Preparatory stage

Before transforming an old door, you must first prepare the surface and remove the previous coating. If you remove the product from the hinges in advance, it will be more convenient to carry out repair work. Place the door on a flat surface, use a table or goats for this. Remove from the canvas: handles, hinges, latches, locks. Replace parts with new ones if they become unusable. Do not forget to remove the glazing beads and remove the glass before starting repair work.

It will be much easier to act by adhering to the following points:

Using a blow dryer, heat up the surface so that the old paint is removed much faster. When the layer begins to soften, use a spatula to remove the coating.
It will be possible to repair scratches and defects thanks to putty and putty for wood.
Take sandpaper with different grits. Sand the surface and sand thoroughly.
It will be possible to fully update the old doors with your own hands if you distribute drying oil or stain on the surface. Such a measure will protect the canvas from moisture, and give the tree a beautiful shade.
Insert the glass back into the door leaf, use new glazing beads.

If you paint a door or glue wallpaper on a canvas, then do not forget to prime it first. Choose a special primer or liquid diluted glue.

Self-adhesive film

When ideas on how to glue an old door have come to a standstill, choose the simplest and most inexpensive option in the form of a self-adhesive film. Geometric stickers can be distributed on the canvas, even if you do not first remove it from the hinges. Choose a film of a bright shade to create a contrast with the overall tone. If you match the stickers to the color of the door, it will look tasteless.

Before sticking the film with a pencil, make a markup where the patterns will be located. After that, apply the sticker to the canvas and use a rag to get rid of the air under the film by carefully wiping it. A canvas on which you can draw inscriptions with chalk will look very stylish and impressive. The cost of such a film is not cheap, but such an option will look very unusual.

Dye

In the process of updating an old door, as in the first case, it is important to use another inexpensive option - paint. Here you have to remove the door from the hinges in order to get the door painted as neatly as possible. You can choose absolutely any color - it all depends on taste preferences and the interior. Buy acrylic or water-based paint as it does not bad smell. From alkyd paint better to refuse.

Experienced "artists" will be able to paint the door using dye in cans. For beginners, it is better to refuse such an idea, since it will be difficult to apply the material in one tone, since the dye will be sprayed on different sides. If you chose the standard painting option, then take matte, not glossy paint. In the second case, the dye will only emphasize all the defects and irregularities of the canvas.

Before updating the doors without changing them, take a roller to make the painting process as comfortable as possible. A wide roller is suitable for smooth and solid doors. It is best to paint the doors in 2-3 layers, applying the paint in a fairly thin ball.

How to update an old door with wallpaper: several methods

It is not difficult to glue wallpaper on the door leaf, and at the same time, all stages of work will not take much time. You can create a beautiful contrast if you choose a wallpaper with a color that will differ from the colors of the walls. Having previously prepared the doors and primed them, it will be possible to paste the wallpaper according to the following scheme:

Dilute the adhesive according to the instructions on the package.
Spread the adhesive backing onto the canvas.
Gently begin to paste the wallpaper and do not forget to remove the bubbles. This will help a plastic or rubber spatula, which must be moved from the center to the edges.
Use a metal strip and a wallpaper cutter to trim the edges of the wallpaper.
Wait until the wallpaper is completely dry to move on to the next stage of decorating if necessary.

If desired, apply additional decor on top of the wallpaper.

Molding

If, before updating interior doors with your own hands (according to the photo with instructions), you purchase foam or polyurethane moldings, as well as sockets, then the decor will turn out to be quite unusual. This option will beautifully emphasize the room, decorated in a classic style. Using rounded moldings and a bright background, you can decorate a room in Provence style.

After you have time to paste the wallpaper and they have already dried, use a pencil to mark where the moldings will be. Using a tape measure, measure out how much material you will need to complete the decor. Cut the edges of the molding at a 45 degree angle. Then take PVA or other glue, process the back surface of each element and glue according to the markup. Wait until the glue is completely dry.

Wall mural

Give the room perfect the new kind it will turn out if you stick photo wallpapers on the door. This finish will look very bright and will help transform the interior of any room. You can order photo wallpapers in any printing house. In this case, it will be possible to individually select the design and type of pattern. Before updating old wooden doors with your own hands in a similar way, you should follow the previously given instructions for sticking ordinary wallpaper.

The effect of antiquity

In the process of updating the old door with paint and sandpaper, it will be possible to create the effect of antiquity. Before moving on to the decor, cover the canvas with dark paint in several layers. After that, apply light paint on top of the previous layer. When the dye is completely dry, take your sandpaper and start sanding the top layer so that the dark paint shows through.

Using the effect of craquelure, it will also be possible to visually “age” the doors. To do this, use varnish or paint, which, after hardening, will visually form cracks.

Decoupage

Decoupage of an old door will look very nice if you use ordinary napkins for decoration. Before starting work, paint the canvas white. Then take a three-layer napkin with beautiful pattern and cut out the image with scissors. Peel off the colored layer and gently apply it to the door.

Dilute PVA glue and water in the right ratio and take a brush. Apply glue to the back of the pattern and attach it to the door. You can repeat this procedure several times until the entire application is completed. At the end, open the surface with acrylic varnish.

glass inserts

One more good way how to update an old door with your own hands (using the photo clearly) you should try to replace the glass. Install new glass in the door leaf or update the decor of the old one. The stained glass technique will look unusual.

Before you paint the doors and create an unusual stained glass window, prepare the following tools:

stained glass paints;
gloves;
circuit;
marker.

It is most convenient to paint glass in a horizontal position. Using a marker, draw the outlines, and then paint the middle on both sides with paints. You can complete the whole picture by gluing small stones or pieces of glass. These details should also be outlined with a black marker on top of the drawing.

Before ennobling an old door with your own hands, take this recommendation into service. Cut small holes in the door leaf and insert small multi-colored pieces of glass into the middle. A similar method will allow you to create a beautiful composition of glass. This option is suitable if the door leaf is made of solid wood.

Stencil decor

Uncomplicated and yet beautiful option- design of the door on a stencil pattern. You can prepare a stencil yourself or you can buy it in a building (stationery) store ready-made. Take thick paper and cut out the pattern you like. You can also prepare a self-adhesive film in the same way.

First, pre-treat the door, then take a stencil and carefully go over the top with a paint roller. Spray paint is also suitable for decoration. Make sure that the template fits snugly against the surface of the door, otherwise extra smudges and stains will appear on the canvas.

Paint the door white first, and then use stencil patterns. Black and gold drawings will look very nice on a light background. When updating interior doors with your own hands, also use, on the contrary, a dark background and light stencil patterns.

art drawing

Art lovers can pay attention to such an unusual option for decorating doors. It is enough to first paint the doors in one tone, and then use additional paints and brushes for painting. The drawing can go beyond the doorway by 10-20 cm and be a beautiful continuation of the composition.

If you don’t have any special talent, but you can restore the old door with your own hands, as you want in the photo, then first take a pencil in your hands. Draw a sketch with a pencil, and then proceed to paint. Pre-cover the floor and walls protective film so that the spray does not spoil. In order to create a memorable design, give the children paints in their hands, where on the canvas they can express their creativity. Such art will give a lot of positive memories and emotions.

Textile

In the case when there are no ideas of what can be done with the old door, but you really want to decorate it unusually, the option with textiles is ideal. This is a very time-consuming process, but the design of the doors will turn out to be truly homely and cozy. Before proceeding to the arrangement of the door leaf, first buy a fabric with the patterns you like. Avoid too light colors, as stains and defects will appear on such a surface very quickly.

Choose a material in the store that will blend in color with the rest of the decor as organically as possible. Use double-sided masking tape to make gluing textiles as convenient as possible. Spread the tape around the entire perimeter of the door. Make sure that there are no wrinkles on the edges of the door, and that there are no shreds.

Door lamination

You can update the appearance of the room if you apply the film on the doors yourself at home. To do this, buy a self-adhesive film on an adhesive basis in a hardware store. First, pre-prepare the door leaf and cover up scratches and bumps. If necessary, remove a layer of old paint.

When gluing the film, do not forget that it is very quickly connected to the surface, so you will have to work very carefully to prevent the appearance of bubbles and bumps. Paste the film gradually by millimeters, use a plastic wallpaper spatula to prevent defects.

By choosing one of the above options, it will not be difficult to update the door yourself at home. It is important not to forget about the rest of the interior of the apartment when decorating and pre-protect it with a film.

Do-it-yourself door restoration allows you to update the interior without investing. Doors made of solid wood lend themselves especially well to restoration. In fact, there are many ways to update the door, returning it to an attractive appearance. Restoration of doors can be carried out qualitatively with your own hands, but for this you need to correctly perform the preparatory work.

Do-it-yourself restoration of old interior doors

With prolonged use, many defects appear on interior doors. The most common breakdowns include:

damage and falling off of platbands;
cracks;
kinks;
detachment;
mashing;
equipment failure;
panel peeling;
broken glass;
creak.

The most difficult to correct is the curvature of the multilayer web. Such a defect often appears due to the saturation of the material with water. In addition, a similar problem may occur as a result of technical irregularities during production. A door made of fiberboard and MDF often suffers from such a defect. It is not always possible to restore a door from these materials in the presence of severe deformation and delamination.

In some cases, it is much easier to make an effort and update interior doors than to change them. Restoration should be carried out if:

non-standard sizes;
there is a risk of violation of the wall cladding and the integrity of the opening;
there is an ornament and texture of the canvas;
no irreparable defects.

You should not try to refresh the appearance of interior doors if their canvas or box is badly cracked, dried out, or the integrity of the structure is broken. In the presence of strong deformations and distortions of the elements, restoration is impossible. It is difficult to restore doors made of such cheap materials as MFD, chipboard, etc. If the leaf has delamination or swelling due to moisture, it will not be possible to eliminate such defects. Particularly problematic is the restoration of veneer doors.

Preparing for Recovery

Before proceeding directly to the restoration, you should prepare the tools and materials that may be required during work. These include:

a set of spatulas;
screwdrivers;
electric drill;
pliers;
sandpaper;
building hair dryer;
gas-burner;
chemical solvents;
electric grinder;
carpentry knife;
chisel;
varnish or stain;
hammer and nails;
flute brush;
roller;
glazing beads;
primer;
paint for wood;
putty;
antiseptic impregnation.

Kit necessary tools depends on the nature of the existing defects. To update a wooden door, it is often necessary to carry out more work than planned, since many defects cannot be hidden by paint. To improve the decorative characteristics, you can use vinyl stickers, photo wallpapers, stencils, false facades and other materials.

We remove the canvas from the hinges, free from the handle and canopies

To facilitate restoration work, it is advisable to remove the canvas from the hinges and place it on a flat horizontal surface. Removing the canvas is not difficult, but it is advisable to use the help of another person who can support the canvas if necessary. If the hinges are not painted, you can remove the retaining pins from them.

However, if the hinges have been painted over many times or are of such a design that the locking pins cannot be removed, another method may be used. First, paint is removed from the hinges at the points of their attachment to the luda. After that, in order to remove the canvas, you should open and unscrew all the screws that fix the hinges.

The removed canvas must be placed on a flat surface and the places of fastening with self-tapping screws of the handles must be freed from paint. They need to be unlocked. If already unscrewed hinges and handles are not removed after removing the screws, the problem may be in adhering paint. In this case, you can use a chisel and a hammer.

Dismantling the paneled door leaf

Most types of doors have a panel structure, i.e. their leaf includes frames, crossbeams, inserts of curly elements or glass. Such inserts complicate the repair process. To ennoble old interior doors of this type, it is often necessary to completely disassemble them.

First you need to inspect the canvas and identify the location of the tongues connecting the individual elements. In most cases, they are located at the corners of the jumpers. After that, the tongues should be drilled with a drill. To separate the structural elements, it is better to use a wooden mallet. After that, work is carried out to restore individual elements. In some cases, you can do without parsing.

Restoration of the web geometry and its strengthening

When the question arises of how to restore an old door, you need to pay attention to the safety of its correct geometric parameters, since wood can swell during operation due to moisture. Poor closure may indicate the presence of such a problem. It is almost impossible to repair an MDF door that has been subjected to such an impact. However, if the canvas is made of solid wood, it must be carefully planed from the ends.

Ways to remove old paint

To update wooden interior doors, varnished or painted, decorative coating need to be removed. Solvents are often used to remove old paint. good effect gives a remedy such as B52. It is necessary to carry out work on the street or in a well-ventilated area, since pairs of such chemicals are extremely toxic and can cause poisoning.

The process of removing old paint with solvents takes some time. To remove the coating, the chemical is applied to a small area. After the paint softens, it is scraped off with a metal spatula.

Before you update the old doors with your own hands, you can apply thermal exposure to remove the paintwork. Most often, a gas burner or a building hair dryer is used for this purpose. Under the action of high temperatures, the paint moves away from the wood and can later be easily removed with a spatula or scraper.

This method of removing layers of paint has its drawbacks. Often decorative material peels off unevenly, therefore, additional thorough cleaning of the surface with sandpaper of varying degrees of abrasiveness is required.

If you have a grinder, it is best to use it. To carry out work to remove the old coating, it is best to take the canvas outside, because in the process of doing this work there will be a lot of dust. Be sure to wear a protective mask and goggles.

If there are many layers of paint on the door, you should stock up on spare grinding wheels in advance, as they quickly shrink and become clogged with dust. Areas of bends and corners must be cleaned with a chisel and sanded. Using this method of cleaning wood, you can quickly achieve the desired result. After removing the protective paint layer, the surface must be sanded.

Glass replacement

Glass is replaced not only if it is damaged, but also when you want to update old interior doors. This stage of restoration has its own characteristics. It is easier to replace glass if they are fixed with glazing beads. They can be picked up with a spatula.

After that, it is necessary to remove the nails with pliers. After removing the glass, you need to clean the bed with a knife and spatula. After that, measurements are taken. The glass must be 0.3 mm smaller than the frame. If desired, you can use an acrylic shatterproof mirror. Both frosted and clear glass can be inserted. The opening must be treated with a sealant. After that, glass is inserted. It is fixed with staples. For fastening, thin carnations are used.

Door putty

The final step in preparing the door for decoration is its putty. It allows you to eliminate existing irregularities and defects. To eliminate chips and cracks, which are often full of old wooden doors, you need to apply a small amount of diluted wood putty to the spatula, apply to the surface and leave to dry. If there are deep defects, you can repair them with a mixture of sawdust and wood glue.

It is advisable to hammer large cracks with sized chips and treated with wood glue. This method of eliminating chips and cracks is difficult to perform, so if you do not have skills, you should not use it. It is necessary to allow the putty to dry and the wood glue to dry. The finished surface is carefully polished with sandpaper. After that, you need to apply a primer and let it dry.

Designer decoration of old doors

There are many ways to update doors without changing them, allowing you to make its surface original. When decorating doors, you can use different materials and hand tools. Design decoration doors is especially important for people who want to make the interior of the house individual.

Decorating the door with fabrics

Updating doors with fabric allows you to completely change its appearance. When decorating, you can use both plain pieces of fabric and small patches that differ in color. It is better to glue the fabric on the Bustilat mastic. The composition should be applied to a piece of fabric, and then glued to the surface. After that, it must be carefully leveled with a spatula. Additionally, you can glue sequins, cords or baguette frames.

Decorating doors using decoupage technique

The decoupage technique can also be used to decorate doors. In the process, you will need the following tools and materials:

acrylic lacquer;
patterned napkins;
PVA glue;
brush with natural bristles.

Previously, the canvas must be coated with a primer and painted in the desired color. Napkins should be stratified, separating the top layer with a pattern. After that, it is necessary to break along into 3 parts. After that, they need to be glued to the surface of the PVA door. Gradually, the entire decorated surface is filled with napkins. After about a day, the drawing is opened with acrylic varnish.

Door decoration with self-adhesive film

To simple methods of updating doors is the use of self-adhesive film. In the process, you will need the following materials and tools:

sharp knife;
film;
a spray bottle with soapy water;
soft cloth.

You can fix the self-adhesive film only on a clean, flat surface. After that, spray the surface with water. From one corner of the film, the protective layer should be removed and glued. After that, gradually removing the protective part, you need to glue it across the entire width. In this case, you need to run a soft cloth over the surface in order to expel air from under the film. When the top is glued, it is necessary to gradually remove the protective shell, move down. Thus, slowly you need to glue the door with a film to the very bottom.

Children's drawings, art painting

You can effectively decorate the door with children's drawings. If there are children in the house, you can ask them to draw drawings of any subject on the door leaf with acrylic paints. After that, the surface is opened with a water-based varnish. In addition, you can independently paint the surface with drawings of any complexity.

lamination

On sale there is a special laminate for lamination. It is glued to the base with a cold method. The only disadvantage of this method is the high cost of the laminate.

Wallpaper with moldings, photo wallpaper

Often, wallpaper with moldings and photo wallpapers are used to update interior doors, on which, thanks to the available technologies, three-dimensional images can be applied to special paper. Pasting a simple canvas with photo wallpaper is not difficult. First you need to apply glue to the canvas. After that, photo wallpapers begin to be glued from top to bottom. Bubbles must be driven out with a rubber roller. The edges are trimmed with a wallpaper knife. You need to wait for the wallpaper to dry.

Staining, varnishing and staining

Often, when a door is being restored, preference is given to varnishes and paints. Before staining, it is necessary to seal the existing glass inserts with masking tape. It is better to use paint specially designed for wood. It can be applied both with a spray gun and with a brush, making movements along the wood fibers. The painting process is carried out in 2 stages. First, a basic white coat of paint is applied. In this case, it is necessary to ensure that there are no smudges. The second layer is tinting, so it can be any color.

If during the preparation process it was not necessary to repair large cracks, which entails the appearance of visible defects, transparent varnishes can be used to emphasize the color and structure of the wood pattern. Before painting, wood stain should be treated. To update old wooden doors with your own hands, varnish can be applied both with a brush and with a spray gun. Leaks should not be allowed. It is often necessary to apply several layers of varnish. Stain is applied in a similar way.

Stencil coloring

Using stencils, you can achieve a good decorative effect. First you need to paint the canvas in the desired color. After the base layer has dried, pre-prepared stencils of drawings are attached to the surface. After that, empty areas in the stencils are painted over. You need to make sure that the paint does not spread. Stencils can be removed after the paint has dried.

Veneering, door stickers

If desired, you can independently carry out veneering with a special film. It is best to work together. First, the film should be fixed on the surface, and then ironed with a hot iron. Water under the influence of heat will firmly adhere to the surface. When attaching the film, make sure that there are no bubbles under it. On sale there are special stickers on the door, which can be fixed both hot and cold.

Having completed repairs in the room, the owners may be faced with the fact that the old interior door does not match the new interior, although in terms of its functional abilities it can still last for some time. In this case, you should think about how to update the interior door with your own hands. There are several decorative techniques that differ in the complexity of execution and the cost of materials. You just have to choose the most suitable one.

Preparatory work

Before decorating interior doors, they are prepared. For this, the following tools are used:

building glue;
tracing paper;
Press.

The door needs to be removed. Then examine the canvas for defects. If the old box has scratches, they need to be repaired with wood putty. You can decorate the canvas with photo wallpapers. If in some places the doors are peeling, then an adhesive mixture is applied, tracing paper is applied, and pressed. An adhesive mixture is also used to seal cracks and micro-crevices. If the defects are large, chips with fine dispersion are added to the adhesive composition.

Door Upgrade Methods

Simple ways to update the canvas include:

applying varnish;
staining;
the use of stain and veneer;
stained glass

Staining, varnishing and staining

Old wooden doors can be renewed by staining, varnishing and staining.

For water, synthetic and organic dyes are used. After that, the door acquires a neat appearance.

The door leaf is possible. Wood varnish is well absorbed into the wood, evenly covering the entire surface of the structure. The main plus of the protective and decorative composition is the presence of a tinting base.
To apply varnish, a sprayer or brushes are used. Experts advise to ennoble the tree with a brush that easily repeats the structure of the structure, well impregnating hard-to-reach areas. To boost protective properties, it is recommended to paint the door in 2 layers.

If you have to refresh the box again, a stain is used. Then the coating is varnished. Stain can be used to update colors canvases. It prevents the mixing of tones, and due to the subsequent varnishing, the brightness of the color is enhanced. Sanding results in a matte finish.

If there is no need to create a matte surface, polishing and drying is carried out after grinding. This technology gives the door a crystal shine.

Veneering

To decorate the door, veneer is used. This method of decorating wooden canvases is used if they are made from cheap sawdust. Due to veneering, the door acquires an aesthetic appearance. The veneer must be glued transversely relative to the wood fiber.

The veneer gives the door a noble look of a real solid wood

Self-adhesive film

You can decorate the box with self-adhesive vinyl imitating wood. With this technique, coating defects are easily hidden. Before pasting a wooden door, you will need to prepare a hair dryer, cloth, scissors.

At the first stage, the coating is cleaned of various defects. This stage is considered the most difficult. Next, markup is performed using a tape measure. These canvases are transferred to millimeter markings made by the manufacturer on the reverse side of the film. For cutting the product, a knife is used.

The film hides all minor defects and gives the surface the look of natural wood.

The cut pieces of self-adhesive are applied to the desired section of the door. On the wrong side of the film there is a protective layer, under which there is glue. Carefully separate a few centimeters of the layer to stick the product on the door.

The overlay, completely applied to the door, is smoothed out with a rubber spatula or a soft material. Self-adhesive is wrapped on all ends of the coating. Immediately cut the corners of the PVC product, install a lock with a handle.

Wall mural

With the help of modern photo printing, an image is transferred to paper right size. Photo wallpapers on wooden doors look beautiful. The image is printed any. To do this, you can use the services of an advertising agency or a printing house. The image can be selected at home or with the help of specialists.

One of the options for updating interior doors are photo wallpapers.

On plain wallpaper, you can stick polyurethane or foam moldings. In this case, the style in which the doors were decorated will change. The resulting design is suitable for a room decorated in a classic style. If you use a colored background or rounded moldings, then the doors will be decorated in the Provence style.

Before applying the pattern, the surface is leveled, treated with glue. If the paint lags behind the door, it is removed. Wallpaper is also treated with glue.

A rubber roller is used to level the canvas. If bubbles remain, they are removed with a plastic spatula. Then the remaining air is removed from the center of the structure to the edges. With the help of this spatula, the joints of the wallpaper (if any) are ironed. If the technology is performed correctly, then the joints are not visible.

Wallpapers with moldings are suitable for interiors in a classic style

The edges of the wallpaper must be cut with a knife. This is done until the wallpaper softens from the glue. Otherwise, they will tear and stretch easily. Leave to dry for several hours. The process of decorating fiberboard or solid wood continues after 12-24 hours. It depends on the temperature and humidity level.

A simple pencil is used for marking. After the drawing has been applied, you will need to measure the length of the constituent elements of the molding with a tape measure. Then they are cut off, and the edges are cut down at an angle of 45 degrees. Using PVA glue, the back surface of the pieces is smeared. They need to be glued according to the markings. When the canvas has dried, it can be installed back. According to this principle, at home, you can update the doors of the bedroom, nursery, kitchen.

Drawings and paintings

The advantages of this decor include:

beautiful and original appearance;
simple execution;
the ability to use ready-made stencils;
wide choice of materials;
implementation of different ideas.

The disadvantage of the method can be considered that its application requires the presence of an artistic skill..
At the first stage, the coating is degreased with alcohol, treated with a primer. The last composition is applied twice. Applies similarly acrylic paint. Each subsequent layer of paint is applied after the first layer has dried.

When zoning, the shape of the paneled part of the coating and the geometry of the ornament are taken into account. To give the surface a vintage look, the contours of the zones are covered with a different color. The paint can be applied with a sponge. The stripes that protrude from the door can be painted golden. Then the ornament is transferred to the surface and signed in suitable colors.

Decoration using decoupage technique

Decoupage does not require dismantling the door structure. You just need to wash and dry the coating. The opening is pre-pasted with mounting tape. The tree is well and qualitatively primed. The surface is rubbed with a simple paraffin candle, and then painted. The next step is gluing a decoupage card. Pre-soak it in water for 12 minutes. The remaining drops of water are wiped off with a rag. The back of the strips and the surface of the door are treated with PVA glue.

For decoupage doors, special decoupage cards are used.

Each piece is glued tightly. In this case, you need to ensure that wrinkles and bubbles do not appear. If such defects are not eliminated immediately after their appearance, the coating will turn out to be uneven.. If the coating is dry, putty is applied to the edge of the constituent elements. Excess composition will need to be removed with a wet rag or emery. A lacquered box will require a longer preparation for painting. Lacquer is pre-removed, defects are eliminated.

If necessary, the edges of the canvas are processed, scuffs are left. This technology will give the coating a vintage style. If observed step-by-step instruction, then the finished decorated doors will look original with details of different shapes. They can be cut from napkins. The color of the future canvas is selected taking into account the shade of the interior of the entire room. Sticking of the material is carried out according to the above method. The finished coating is varnished with an acrylic base.

Antique decoration

Antique wooden door can be seen not only in apartments, but also in houses and offices. At the same time, decor that imitates antiques is rare. It gives the door leaf individuality. By craquelure is meant a two-layer application of varnish on the door. Particular attention is paid to the process of varnish selection - each layer should have a different composition and different time drying. Preliminary cleaning, degreasing and drying of the coating is carried out.

Craquelure gives the door the look of old wood

To age the door, you will need some materials:

special varnish for craquelure;
bituminous varnish, which gives the effect of antiquity;
acrylic paint.

A craquelure varnish is applied to the prepared coating. If the 1st layer is dry, the 2nd layer is applied - bituminous varnish. It is needed to enhance the contrast when a white background is used. If a dark tone is applied, acrylic paint is applied. This technology is considered the best. If necessary, craquelure varnish is replaced with simple PVA glue, vinegar, egg white or gelatin. This method of updating doors is suitable for people who like antique style.

Decor with stencils

With skill in handling wooden products you can use a more complex canvas update. To apply decor with a stencil, you will need:

leather;
glass or mirror tiles;
stained glass;
mat;
bamboo curtains;
bars;
veneer.

To carry out such a decor requires perseverance and a good imagination. As a result, it will be possible to make an original door that will fit perfectly into any interior.

Using stencils, you can change the design of the door

The door, the canvas of which is replaced by a stained-glass window, gives the room an unusual look. To implement this idea, water-based paint is used. Previously, the desired pattern is thrown onto the surface. Paint is used to transfer the design to the glass coating. This procedure is performed in a certain sequence:

preparation of a sketch of a drawing on paper;
glass processing by cleaning and degreasing;
substituting the picture to the glass, followed by its stroke on the back side with a thin brush;
drawing the contours of the drawing with different colors of paints.

After the process is completed, the paints must dry for 22 hours. Then a piece of glass is mounted in the door, well fixed.

Renovation of the opening and slopes

In addition to the door itself, the doorway is also updated. If this is not done, then the canvas will have an unfinished look. In order to successfully complete the above work, it is recommended to gradually consider the finish.

The finishing of the slopes and the opening must match the interior of the door and the room

At the first stage, the reference guides are processed. Then they are repainted in the same color as the door leaf. In case of severe wear, plasterboard sheathing is mounted on the guides. In the presence of roughness, perforated type corners are used for sheathing. Then the opening is repainted.

Subsequently, it will be required correctly. For their installation, special clamps are used that hold the platbands well. In the absence of clamps, glue or self-tapping screws are used.

If the door is updated only with an opening, and the slopes remain the same, then the decor process is considered incomplete. Various methods are used to finish slopes. More often, special MDF strips are used to update the slopes. You can also install drywall slopes that are fixed to perforated corners or glue.

Another method of finishing the slope is plastering. This process is the most time-consuming and requires experience and qualifications in this case. Experts believe that the best solution is plastering followed by the installation of perlite slopes, which are not cheap. But in the end, you can get strong and durable slopes. They don't get mold.

Any quality interior door eventually loses its original appearance. As a result, it may need to be replaced or restored. The first option will require a lot of money, so it's best to think about a new design design. So, how to update the interior door with your own hands?

Preparatory work

Buying doors every few years is very expensive, so many people decide to do everything themselves. But before proceeding with the design of a wooden door, careful preparation should be carried out.

We carry out the work in the following order:

We remove the updated door from the hinges. To do this, you need to open it slightly, attach a crowbar to the bottom edge and press.
We lay the structure on a flat surface or rest on something.
Carefully remove the wooden glazing beads and take out the decorative glass.
We remove all components (concerns the door with a lock, hinges, handles).
We heat the surface with a building hair dryer and remove the old coating with a spatula. If this is not done, the new finish will not last long. old paint can be removed with sandpaper, solvent.
We find all chips, cracks, various defects and fill them with putty (or special putty).
We level the coating with a grinder or sandpaper so that it becomes even and smooth.
We wipe the surface to remove dust from it. Don't wet too hard.
We cover the structure with stain or drying oil.
We paint with varnish (in 2 layers). If the restoration of doors will be carried out using other materials, then we cover them with a primer (in 2 layers).
We insert glass with glazing beads, fittings and return the structure to its place.

Painting or varnishing

The fastest and easiest finishing options are staining and varnishing. Paints are different, but for the processing of doors it is better to choose acrylic, oil, alkyd and perchlorovinyl. Do not use water-based formulations, as they are wiped off over time, and hand marks remain on the surface. Concerning color solution, then the finish can match the shade of the walls or create a contrast with them.

Varnish compositions create a transparent coating on the surface, under which the pattern of wood is visible. This fact should be taken into account, because all defects will be visible. Polyurethane composition is considered the best for doors, because it is durable and resistant to mechanical damage.

How to paint a door or varnish it? We perform work as follows:

remove the old layer of paint (lacquer) with blowtorch or industrial hair dryer;
clean and degrease the surface;
we find all the chips, cracks, dents and putty them;
cover with a protective compound;
take a brush and paint (varnish) in several layers;
waiting for complete drying.

Veneer

The veneer is made from wood and is a thin plate different color and textures. For its production, oak, walnut, linden or mahogany are used.

How to update an interior door with veneer? The process looks like this:

We remove the old door from the hinges and lay it on supports (you can take ordinary stools).
We dismantle handles, hinges, locks, glass (if any).
We inspect the door for defects. They will have to be plastered.
Let it dry and clean it with sandpaper.
We dilute with water protein or mezdrovy). Its readiness is determined by a stick: we immerse it in the composition and pull it out (it should drain in a thin stream).
We heat the glue and apply it to the surface to be trimmed.
We wait about 5 minutes and apply the veneer.
We carry out grinding with a damp cloth, and then with a hot iron. Movements can only be made along the fibers, and from the center to the edges.
We lay the remaining plates with an overlap, since the material narrows when it cools.
After cooling, cut off the excess veneer and heat the surface with an iron.
We process the joints with an adhesive film so that the seams do not diverge.
We are waiting for the material to dry and remove the film.
We use varnish based on rosin and shellac. It should be applied in 3 layers, each of which must dry completely.
We return locks, handles, hinges to their place.

Wallpapers and photo wallpapers

A great way to update a room is to wallpaper the door. Even inexpensive material will make the design stylish and beautiful. In the selection process, not only your own taste is taken into account, but also compatibility with the interior. This design option is very popular abroad (in the USA, Sweden and Canada). The wallpaper on the doors, separated by compartments, looks very beautiful and unusual. If glass is present in the structure, then it is removed and plywood is inserted. Wallpaper is glued on top of it.

If there is a geometric pattern, then it is aligned vertically. On the double doors The picture must be symmetrical. Places where there will be no wallpaper should be painted in the color of the material. Installation is carried out in the following order: the surface is cleaned, degreased and primed. If necessary, grinding is done. For gluing wallpaper, PVA glue is used.

Doors with photo wallpaper look very beautiful and unusual. Of course, they are not cheap, but the variety of patterns will allow you to get a unique finish. Landscapes, animals, views of the night city, etc. will well decorate any room. The material is glued in the same way as ordinary wallpaper. But you have to think in advance about the completeness of the drawing.

Self-adhesive film

This option for finishing doors is considered one of the most expensive, since the material is quite expensive. Its main characteristics are density, beautiful appearance and durability. In order for the film to adhere well and remain smooth, it will be necessary to level the surface with high quality.

Let's figure out how to update the interior door with a self-adhesive film:

we remove and prepare the structure for finishing;
spray it with a spray gun (it’s easier to lay the material in the correct position);
turn the film on the wrong side and peel off a small area;
apply the material to the surface;
carefully place it with a spatula or roller;
pierce the bubbles with a needle and smooth the coating.

The dimensions of the self-adhesive film allow you to completely close the canvas. But if you wish, you can use small stickers on the door. This option is perfect for a child's room.

Fabric trim

Finishing doors with fabric is done in the likeness of wallpapering. IN this case it is important to choose the right glue - it should not leave stains on the material. If the choice fell on loose fabric, then you will have to tuck its edges. Working with it is a little more difficult than with wallpaper, but the result exceeds all expectations. This is due to the fact that the variety of colors of the material is wider than that of the wallpaper.

How to update an old interior door with fabric? There are several finishing options:

Paste over with small pieces of fabric collected in one canvas (patchwork).
We make the bottom of the structure (approximately 2/3) of fabric, paint the top. On the border, you can place a molding, special lining).
Instead of glass, we insert a drapery made of fabric, assembled on a thread or fishing line. It can also be completely closed.
We make several square or rectangular inserts arranged vertically.

Polyurethane lining (moldings)

Polyurethane moldings look very stylish and beautiful on the doors. If desired, you can purchase wooden lining. You can see them in stores in different colors and designs. They represent various panels, borders, arcs (and their halves), platbands. As for the surface of the products, they are: smooth, embossed, with ornaments, etc. Entire compositions are assembled from such an arsenal.

How to update an interior door with moldings? We take liquid nails or any construction adhesive and fix them on the structure. On sale you can see self-adhesive products, the installation of which is greatly simplified. To assemble complex compositions, you will have to apply a sketch on the door in advance.

Vinyl stickers

A great way to get an updated interior is to use door stickers. They can be in the form of landscapes, animals, plants, cities, children's drawings, unusual patterns, etc. As for the size, the stickers can completely or partially cover the canvas, and also consist of small elements. Their main advantage is that when they are removed, no traces remain.

There are stickers that look like a slate board. They are well suited for children's rooms, because you can draw on them with chalk. There is nothing complicated in using stickers. Small items can be glued on their own, and large ones - with someone else's help. In the process of work, you need to carefully smooth the sticker so that its surface is even.

Renovation of doors with glass inserts

If it is necessary to update doors with a mirror or glass, then several finishes can be used. Stained-glass windows painted with special paints will look unusual. For work you will also need: stencils, a sketch, contours on glass (silver, white or black).

The process of decorating doors with a stained-glass window (for example glass construction) is done as follows:

lay out the sketch on a flat surface;
lay the canvas on top;
we circle all the lines of the stained-glass window with an artistic outline;
we wait for drying and fill the space between the contours with paints (colors - to your liking);
let it dry and set the canvas in place.

So that the decorated door does not look too pretentious, you can paint any other piece of furniture (chandelier, chest of drawers, etc.) in the same way.

Mosaic

You can also decorate the door with a mosaic. It is suitable even for the bathroom, as it is resistant to moisture. Ceramic or glass compositions are assembled from these small elements. The uniqueness of the design will give additional decorations in the form of sea or river pebbles.

When choosing a material, one should take into account the fact that the weight of the door increases due to the mosaic. It is very important that door frame I was ready for such a load. Wood veneer will help reduce the load or acrylic glass(instead of stones and ceramics).

Let's try to figure out how to update the interior door with your own hands. First, sketch it with simple pencil. Then we take "liquid nails" and begin to glue large fragments. When they are in place, you can proceed to small details.

Decoupage

Restoration of doors can be done using decoupage. The work consists in applying ready-made drawings to the structure (from fabric, wallpaper, napkins, newspapers or ready-made decoupage cards). The decoration process is carried out as follows:

preparing the canvas for work;
cut out the drawings you like and soak them in water;
slightly dry them, place them on the structure and cover with PVA glue (both the drawing and the doors);
we smooth the product well so that there are no bubbles and folds on it;
apply a little putty on its edges (should be matched by color);
grind this layer with sandpaper;
if necessary, cover with varnish (in 1-2 layers).

Decoupage can be done in several ways:

finish some areas (suitable for structures with bulges and curly divisions);
decorate a small part of the canvas or close it completely;
randomly fill in free space or assemble a thematic panel from individual motifs (for example, a world map).

Art painting

Among the variety, it is worth highlighting the artistic painting. If you have the skills in this matter, you can immediately get to work. An excellent effect can be achieved if you use the floor, walls and ceiling in painting. Great option- drawing letters, names, philosophical phrases or any wishes.

But what if there is no artistic experience, but you want to get a masterpiece? Special stencils, which are sold in construction and stationery stores, will help here. If necessary, they can be cut out of cardboard or self-adhesive film.

Let's figure out how to decorate the door with your own hands:

we perform the preparation in the same way as before staining;
we apply or glue the stencil (we follow its snug fit);
Apply the paint with a roller or sprayer.

It is better to supplement the restored design with a new handle, hinges and a lock. Metal fittings wear out over time, so it should be changed.

Decor with improvised materials

How to update an interior door if there are no finishing materials at hand? Any unnecessary items will go into action: shells, lids, mesh bags, egg trays, etc.

Let's try to decorate the doors with the help of egg trays (we save them in advance):

tear or cut paper cells into small pieces;
wet them with water;
arrange the elements in a chaotic manner (or lay out a simple pattern) and fix with glue. A glue gun will help speed up the work;
place the rest of the decorative elements;
cover the surface with spray paint.

Another way to update doors is the sandblasting technique, with which glass inserts are formed. This finishing option will require the involvement of specialists, because it will be difficult to do this on your own.

Making doors with various decorative elements is a real creative process which will bring you pleasure. Also, the owner of the house will be pleased with the result of the work and the opportunity to save money. Thanks to the above finishing options, you can get a truly unique interior door (with a mirror, glass or solid).