home materials

How to hang wallpaper yourself. How to glue wallpaper: the main rules and nuances of work. Optimal conditions for wallpapering

For cladding and decorating walls, the most common and frequently used finishing material is wallpaper. Due to their huge range, they differ in cost, texture and colors. Working with such material is simple, however, it has its own characteristics. And so, how to glue wallpaper of one kind or another? To get an answer to this question, we actually suggest that you study the information presented in this article: where to start gluing wallpaper, their types, features, conditions to which they are suitable.

But, despite this, initially you have to choose the appropriate type of wallpaper. Since everyone has their own characteristics, you should study the advantages and disadvantages of the material before leaning towards one of the options.

Types of wallpaper

The most popular are paper wallpaper , since they have quite a few pluses, but some minuses also appear in them. However, most people look at the cost of wallpaper because they like the low price. And it depends on the type of paper, which is taken as a basis. Paper wallpapers:

Environmentally friendly.
I have high air permeability, which allows the walls to breathe.
They have high moisture resistance.
Easy to work.

However, such wallpapers are not moisture resistant, quickly absorb any smell, quickly become dirty, which means a loss of attractiveness. Therefore, it is not recommended to use this type of wallpaper in the bathroom and kitchen. For such a case, two-layer paper wallpapers are produced. This type of material is more durable, moisture resistant and subject to less pollution. But this type of wallpaper is more expensive than single-layer ones. How to glue paper wallpaper correctly, we have already described in a previous article.

Also as a decoration material are popular vinyl wallpapers

, they are based on paper or
interlining, and their top layer is covered with polyvinyl chloride, unlike paper ones:

Immune to moisture.
Has increased strength.
Resistant to mechanical damage.
Has a low weight.
Virtually no dust or smell is absorbed into them.

However, vinyl wallpapers also have a number of disadvantages, since they are covered with PVC film, which does not allow the walls to breathe. In addition, they are quite difficult to work with when pasting, as some of them need careful work, and some are less capricious, but they are still hard to work with.

Vinyl wallpapers can vary significantly in their type and properties. After all, there are even those that can be painted. Because their top layer is covered with foamed vinyl, and it can be hard or porous to absorb dyes. You will learn more about how to properly glue vinyl wallpaper in the following articles.

Another common type of wallpaper is non-woven., which in their characteristics are very practically no different from paper ones.

Wallpapers like this appearance and properties are similar to fabric, since the coating material is made from natural components. Non-woven wallpaper:

Easy to paste.
Durable.
Breathe.
Do not deform.

In addition, these wallpapers always remain dry during operation, since they are attached to the wall, and the adhesive composition is not smeared on them, but on the surface to be trimmed. They can also be applied to any surface, and can be painted up to 3 times. How to glue non-woven wallpaper read in the following publications of our website.

With various ornaments and textures, there is such a variant of wallpaper as glass which most often do not need painting. This material has:

fire resistance.
Moisture resistance.
Safe and environmentally friendly.
Long service life.

Glass fiber can be washed with any cleaning agent and at the same time their surface will remain without damage. But when covering walls, they are difficult to glue, and they also require quite a lot of adhesive solution. Artificial and natural produce linen or textile wallpapers, in which the top layer is fabric, and the base is made of paper or non-woven. From this depends on their cost and characteristics. This type of wallpaper has a high degree of heat and sound insulation, however, it is unstable to moisture. Even the various impregnations that the manufacturer uses do not make them more moisture resistant.

Video: How to glue glass wallpaper

Attractive in appearance with rich texture metallic wallpaper, the top layer in which is a thin metal, and an ornament or imitation of the textures of metal surfaces is embossed on it. This type of wallpaper is resistant to mechanical stress and damage, it is easy to care for them.

The most important advantage of wallpaper is their environmental friendliness, heat and sound insulation. However, they practically do not breathe, and besides, their cost is very high.

Another original way to decorate walls is special liquid wallpaper., which in their appearance are more reminiscent of plaster than wallpaper. With the help of this material indoors, you can hide the flaws of the walls and when pasting, the seams are invisible. But they do not have moisture resistance and strength and can quickly be damaged. Therefore, it is very important to know how to glue liquid wallpaper correctly.

Choosing the right material and tool

First of all, you need to decide on the type of wallpaper and, in accordance with this, and glue, as well as assemble the required tool for work. Calculate the amount of facing material and glue, taking into account the increase, especially if the wallpaper is patterned. Typically, you will need tools such as:

putty knife;
a small container to dilute the glue;
a simple marking pencil and a brush;
stationery knife or scissors;
rubber roller;
plumb and tape measure.

How to glue wallpaper with your own hands, where and where to start?

It does not matter which room will be renovated, but a number of conditions will need to be met. Initially, you need to prepare the room, and this is to prepare the walls and remove the old coating, level and coat with a primer. Depending on the type of wallpaper you choose, you may leave some flaws on the walls, most likely the wallpaper will cover them.

Before cutting off the panel, it is required to measure the required height, such an action is performed using a meter or tape measure, in the absence of such, it is better to use a bar or a hard thread. Also, when cutting, a small margin of the web should be taken into account. After that, the prepared material is smeared with glue and left for impregnation. In some cases, the technology determines the application of adhesive to the wall. Then it is simply applied to the wall like paint or a primer, after which wallpaper is carefully applied to it. But in fact, this is the most difficult way of pasting.

When applying the prepared material to the wall, it is useful to know where to start gluing the wallpaper. To do this, the lower edge is folded over and transferred to the wall, thus sticking and avoiding dragging the canvas along the floor. In order to fit snugly, it is required to smooth it, and thanks to this, air accumulations and excess glue under the wallpaper are removed.

Selecting a start angle or line

Before you start gluing, you need to decide which side to start with. After all, there are various options:

From the corner, in this case, the walls in the room should be almost perfectly even, this also applies to corners, and this rarely happens, then it is best to stick wallpaper strips at standard landmarks.
From the door, but with such pasting, it is worth observing severe verticality. Therefore, you can start work in an arbitrary reference point that suits you. The most important thing is that the first canvas is glued correctly and a plumb line is used for this. After that, the pasting process is carried out in the course you have chosen.
From multiple lines, this method is used only when the standard options are not suitable due to the presence of multiple windows or other obstructions. Thus, many joints are obtained, and so that they are not noticeable, it is most preferable to make them on top of doors and windows.

Therefore, you need to decide where to start pasting wallpaper so that the seams are invisible.

How to observe the vertical, in case of uneven corners

When the room has crooked corners, and the selected facing material has a geometric pattern, then in any method used, verticality can be lost. It is also difficult to join the pattern to the main glued canvas. In this case, when pasting on each plane, it is better to use a new plumb line. Thus, on any of the walls, the final panel will run around the corner by one or two centimeters of the next wall.

This docking of wallpaper will give the walls a more beautiful and neat appearance. This method of pasting can only be used for thin wallpaper. And for thick ones, it is better to cut off the incoming edge of the material and display it in a vertical line.

Watch carefully how to glue the wallpaper video if you are going to glue the wallpaper with your own hands for the first time and you still have questions.

How to glue video correctly - Master class

Advantages and pasting meter wallpaper

Before ordinary wallpaper meters have a number of advantages, firstly, financial costs and time. Secondly, they have a more attractive appearance, since there are fewer seams on the wall and it is easier to glue and join the pattern, and, moreover, hide some surface irregularities. Thirdly, a huge selection of assortment in colors and textures.

Very often the question arises, how to glue meter-long wallpaper? But there is no difference in pasting from ordinary canvases.

For attentive people, the best assistant is the instruction, in it you will always find tips on how to work correctly. After all, before you glue the wallpaper in the joint, you need to make sure that this type of wallpaper is glued that way.

There is also no single answer on how to start wallpapering correctly, because in every room, usually, always different conditions. Therefore, you should think carefully before applying glue. And best of all, if you are pasting the wallpaper yourself for the first time, then just measure a piece and attach it to the wall without glue. This will help you see how the row will start. Until the wallpaper is pasted, you always have the opportunity to change your mind and start from the other side.

With due diligence and diligence, you will definitely be able to glue the wallpaper beautifully. After all, master builders are not born, and there are no special institutions for study, everyone once began to learn from their own mistakes. Therefore, even if something does not work out for you, do not despair, experience can only be gained by making mistakes.

Wallpapering is the most common option for home renovations. Ease of installation and availability of materials allow you to do the work yourself. In this article, we will tell you in detail how to glue wallpaper with your own hands, starting with the choice of materials and glue, ending with the tricks and advice of experienced maters.

Wall preparation

The preparatory stage should begin with the release of the walls from all unnecessary items. Sockets and switches, skirting boards, as well as door paneling must be dismantled to simplify work.

Let's do everything with our own hands!

We carefully prepared this article before publication, and therefore we will tell you about all the nuances of self-pasting walls: how to choose glue, how to apply it, how to stick it, etc.

It is recommended to de-energize the room to prevent damage electric shock in the production of wet works. If this is not possible, it is necessary to carefully insulate the wires of switches and sockets, and hide them in the sockets.

old wallpaper

Then you should do the preparation of the walls. If the walls are finished with old wallpaper, they will have to be torn off. First, they are removed by hand, and if you're lucky, the strips will come off entirely, but usually they come off badly, in separate pieces. The fragments remaining on the walls are recommended to be moistened with warm water and cleaned with a spatula.

Difficulties may arise with vinyl samples, with a moisture-resistant coating on the front side. It must be removed so that water can penetrate to the base and soak the glue. This will take a lot of time, but then the material will become more pliable and can be easily cleaned with a spatula.

Paint cleaning

If the walls are painted or whitewashed, the cleaning job becomes more difficult. Whitewash should be moistened with plenty of water and gradually removed with a spatula. Oil paint cleaning is more difficult and longer, but there are ways to speed up this process. First, you can use special chemical compounds to remove the paint, the second is to use construction power tools.

The chemical method of removing paint will be expensive, and will require the use of personal protective equipment, due to harmful fumes. As auxiliary tools for removing paint, a grinder or a puncher with special nozzles in the form of metal brushes can be used. In this case, a respirator and goggles are also needed due to the abundance of dust.

alignment

When the room is cleared of the old finish, they begin to level the base. The amount of work at this stage depends on the condition of the walls. A wall with a small number of chips and small defects will require only local alignment. Minor flaws should be corrected with a finishing putty, having previously treated the wall with a primer for better contact.

Pronounced uneven walls will require more attention. Puttying will be required in two layers - starting putty to correct the main defects, finishing for final alignment. At the end, the walls are sanded with an abrasive mesh and cleaned of a layer of dust.

Types of wallpaper

Now on the market of finishing materials there are many options for wallpaper that have certain performance characteristics, advantages and disadvantages. Let's highlight the main types:

Paper wallpaper. The most common type, characterized by low cost and ease of pasting. Paper wallpapers are eco-friendly and great for bedrooms and children's rooms. On the other hand, they cannot be washed and they do not retain their original appearance for long;
Non-woven wallpaper is made on the basis of paper with the addition of non-woven fibers. Differ in durability, wear resistance and not be afraid of water. Gluing non-woven wallpaper is simple - the glue is applied directly to the walls. This finishing material is able to hide minor wall irregularities, which simplifies the process of leveling the base;
Vinyl wallpapers consist of paper or non-woven backing covered with a vinyl coating. They are easy to clean and do not lose their brightness for a long time. Before gluing non-woven vinyl wallpaper, it is worth considering that they do not “breathe”, and it is not recommended to use them in children's and bedrooms;

Acrylic finishing material is paper coated with acrylic composition. Unlike vinyl wallpapers, they have a thin outer layer, and are not as durable, but they are better breathable;
Natural. This type of wallpaper is characterized by environmental friendliness, exclusivity and high price. They contain natural cork, straw, reed, etc. Drawing on the walls requires some skill;
Fiberglass material is ideal for office space. Differs in durability and durability, is not afraid of water and does not burn. After application, it is painted with water-based paints, and this can be done dozens of times;
Textile samples consist of a natural fabric material applied to a paper base. They look chic and expensive, and cost accordingly. They are sensitive to moisture and mechanical stress, and also absorb odors well;

Metallized wallpapers have an outer layer of aluminum foil, are not afraid of external influences and are easy to clean. Ideal for modern interiors;
Liquid wallpaper is the most unusual type of all listed. They are based on cellulose, supplemented with decorative dyes, fibers, sparkles. Walls before applying such a coating may not be leveled. It is not recommended to glue them in wet rooms, due to hygroscopicity;
Wall mural is a self-adhesive film on which a certain pattern is applied. You can depict everything on the wallpaper, from an ornament to a photograph, which allows you to make the room unique.

As a rule, wallpaper for the room is selected based on taste preferences, but in order for them to last longer, their features must also be taken into account.

Wallpaper glue

The selection of glue causes difficulties for many who started repairs with their own hands. In fact, the variety of options presented should not scare anyone, because in order to make right choice it is enough to focus on the type of wallpaper used. There are several types of wallpaper glue, which differ in composition:

methylcellulose glue;
CMC glue, based on carboxymethyl cellulose compounds;
starch glue.

The choice of glue is made on the basis of the following features:

wallpaper type;
microclimate of the room;
wall material.

First of all, you should decide on the type of wallpaper. Manufacturers of adhesives offer a wide range of products on the market, from which choosing the right option is not a difficult task. According to the type of compatibility with wallpaper, glue is:

for light wallpaper (paper);
heavy wallpaper (fiberglass, textile);
non-woven wallpaper;
vinyl samples;
universal, suitable for all types.

How to choose the right glue, taking into account the microclimate of the room? Materials for wet rooms must be resistant to moisture and retain their properties under any conditions. In addition, damp rooms contribute to the spread of fungus and mold. The adhesive composition must contain antiseptic substances to prevent their occurrence.

How to glue wallpaper with your own hands

Wall decoration with wallpaper is a procedure that you can easily handle with your own hands, but it is important to follow certain rules so that the result is of high quality, and the process itself does not take much time and effort.

Final preparations

Before gluing the wallpaper, you must pass the last preparatory stage- priming walls. Priming allows you to achieve better adhesion between the base and the finishing material. For the production of works, you can choose an acrylic primer or use glue. Manufacturers of adhesives indicate on the packaging how to properly dilute it, for pasting or priming walls.

The composition is applied to the walls with a roller, and the corners are processed with a brush. It is recommended to prime immediately before work, so that dust does not have time to settle on the walls, which can impair adhesion. It is also worth providing the necessary conditions in the room itself. For the duration of the work, up to the complete drying of the glue in the room, the windows should be closed.

The most optimum temperature indoors - 20 degrees. It is also necessary to put things in order, wash the floor, so that during manipulations with the wallpaper they do not spoil their appearance.

Where to start gluing

From which wall the pasting process will begin, by and large it does not matter. The main thing is to stick the first strip strictly vertically. If there is no desire to beat the level, it is allowed to take some obviously vertical object as a landmark (window slope or doorjamb). You can start gluing in the corners. The remaining strips will be glued already according to the reference first one and the fitting process will be simplified.

How to prepare glue

All modern adhesives have instructions on how to stick wallpaper on the back of the package. It is necessary to carefully study it before gluing the wallpaper and follow all the recommendations. As a rule, the preparation process is reduced to the dilution of dry glue in water, in the proportions indicated on the package. To prevent the formation of lumps, it is necessary to add glue to the water in small portions, stirring the resulting composition thoroughly.

How to glue wallpaper

First of all, you need to find information on the rules for applying glue on the wallpaper packaging. If the adhesive is to be applied directly to the strips, they must be rolled up with the smeared side inward. The edges are folded to the middle several times. The folds should remain rounded and the wallpaper strip should resemble a scroll.

If, according to the technology, glue is applied to the wall, then it is necessary to coat the base along the width of the glued strip with a margin. To apply glue in the corners under the ceiling and floor, use a brush.

Having climbed onto the stepladder, it is necessary to launch a few centimeters of the glued strip onto the ceiling. The edge of the strip must be aligned with the marked vertical or landmark. Then, with smoothing movements from the landmark to the opposite side, glue the strip near the ceiling.

with a special soft spatula. When gluing wallpaper, it is necessary to monitor the formation of air bubbles, be sure to expel them with excess glue to the edges.

The remaining parts are also glued, only you need to focus on the already glued strip. At the end, you need to cut off the extra parts in the corners near the ceiling and floor. The easiest way is to use a wide spatula and a clerical knife. The spatula is applied to the corner, and the resulting margin is cut off along its edge. As a result, the edges are smooth.

Separately, it is worth mentioning how to stick wallpaper in the corners. There are two ways. The first one involves gluing one strip overlapping on the other side of the corner with a margin. The second strip is cut off at the corner and glued directly onto the stock. If the material is thick, the joint will be very noticeable, and it is better to use the second method.

To achieve a more inconspicuous joint in the corners, the strips are overlapped on both sides and cut off with a sharp knife with a spatula. If the corners were glued tightly, then the stripes would line up perfectly evenly. The outer corners of the room are glued in the same way, using one of the methods.

How to glue wallpaper in the presence of obstacles

For those who understand how to stick wallpaper, difficulties may arise in areas near doors and windows. If the window or door is flush with the wall, it is enough to cut a strip of wallpaper along the casing or jamb with a small margin. Then, to the corner of the casing, the strip is cut at an angle of 45 degrees. The resulting parts must be hidden behind the design of the door or window, and cut off excess remnants.

If the door or window is located in different planes with the wall, the work becomes somewhat more complicated. First you need to glue the slope, leading a small margin onto the wall, cut along the edge with a spatula. Next, you need to glue the wall in the same way.

Also, difficulties may arise when bypassing sockets and switches. If they were dismantled before work, then only installation boxes with wires should remain on the walls, located flush with the wall, which will not interfere with the work.

If for some reason it was not possible to remove the wiring accessories, then it is necessary to attach a strip to the obstacle and mark its edges. Using a knife, cut out the necessary fragment according to the marks, leaving a margin that can be hidden behind a false decorative frame.

If you need to glue the wall behind the battery, it is not necessary to remove it. It is enough to get a certain supply of wallpaper from all edges for her. You may also need information on how to properly bypass heating pipes. If they weigh on clamps, you can dismantle them for convenience, and put them in place after the work is completed. Holes in the walls will not be difficult to find.

How long does wallpaper dry

The drying time of the wallpaper depends on its type. Non-woven wallpaper dries for at least a day, and the thicker they are, the longer it takes to wait. Vinyl wallpaper dries for about two days, provided the humidity in the room is not more than 60%. Drying time for paper wallpapers varies from 24 to 72 hours. It is important to remember that at this time you should not open windows, and generally allow drafts in the room. By following these rules, you can hope for a quality result.

Frequently asked Questions

Is it possible to glue wallpaper on wallpaper? - This is allowed only in certain cases. If the old samples are thin, then most likely they sit firmly on the walls, therefore, they will be a good basis for a new finish. However, how long such wallpaper will hang is a big question;
How much do the services of masters cost? - On average, finishers estimate their work from 150 to 170 rubles per glued square meter;
What to do if the wallpaper peels off? - You can use a brush to glue the detached part with the remnants of glue, or use special glue for seams;
What happens if you ventilate the room during and after work? - It may happen that in a draft the glue dries too quickly, and the material does not have time to stick.

Having decided to stick wallpaper in their home, many people do not know which option should be preferred. There are many various kinds wallpaper, each of which has its own unique features, and this choice directly affects how attractive the final result will be. When choosing the right type, it is important to pay attention to the many various factors and characteristics.

To date, there are more than ten different types of wallpaper, ranging from simple options, such as paper or vinyl, to modern models, such as liquid or quartz wallpaper. Each of the presented options has not only its own gluing methods, but also many other unique characteristics, ranging from service life to maintenance requirements. It is important to study the features of this or that option in advance, choosing the most suitable type for yourself, in which you will not be disappointed even after a few years.

Paper wallpaper is one of the most popular options that has been successfully used for several decades. You can glue it as you like, as these wallpapers are unpretentious. Low cost and a large assortment are the main advantages of these wallpapers.
Vinyl wallpapers today are the absolute leader, as they are inexpensive, have many various options colors and very reliable. The main advantage of this wallpaper is a washable vinyl coating that is resistant to abrasion. Vinyl wallpapers can be divided into two types: non-woven vinyl and paper-based. The main disadvantage of this type of wallpaper is poor breathability and not environmental friendliness. Also, these wallpapers expand when wet, and narrow when dry, which creates certain difficulties when gluing.
Non-woven wallpaper - this is the same paper, but with the addition of polyester fibers, giving them strength and reliability. Non-woven wallpaper is absolutely deservedly considered one of the most environmentally friendly options, with great breathability and durability. This type of wallpaper has no shrinkage and deformation after drying.
Glass fiber is another representative of the finishing material for walls. Mainly used in office space. They are resistant to abrasion, do not require good surface preparation before gluing, reinforce (strengthen) small cracks. In residential areas, they do not look aesthetically pleasing.
Textile wallpaper is a representative of an expensive finishing segment. They consist mainly of natural fabric materials on a non-woven or paper basis. Possess the maximum number advantages, are less prone to fading than others, but have low resistance to dust, dirt and odors.
Liquid wallpaper - inherently refers more to decorative plaster, while combining high quality wallpaper coatings and the flexibility of applying plastic materials.

Wallpaper may vary in roll width. More often rolls are half a meter wide, but there are also meter models. On the one hand, it is easier with them, you get fewer joints. However, there is a difficulty - to cope with them, it will take more effort.

Wallpaper or wall painting, which is better?

If a few years ago wallpaper was the main option for wall decoration, today many people opt for painting, considering this method to be simpler and less expensive. Of course, painting has its advantages, such as the ability to choose any color and a long service life, but wallpapers can also be of different palettes, shades and have different textures, and properly selected wallpapers can last even longer than painting. It is important to understand that high-quality paint preparation is expensive, and high-quality paint costs a lot of money. According to this, with a quality repair, choosing to paint the walls, you won’t be able to save money. Here it is important to understand what do you want to get from your interior? With a large budget, you can choose any type of finish. However, if the budget is limited, it is better to choose wallpaper.

How to glue wallpaper?

Let's first figure out which wallpaper is easier for a non-professional to glue? It's better for the layman to consider simple options wallpaper, such as paper, vinyl or non-woven. These wallpapers do not require any special approach, and anyone can handle them. Enough to have good training walls and purchase the appropriate adhesive.

Regardless of the type of wallpaper chosen, you first need to prepare the wall. Align it and remove the remnants of old wallpaper, if any. In many ways, the success of the whole process depends on the preparation of the walls.

Preparing the walls for wallpaper is as follows:

Dismantling of the old coating (wallpaper, paint).
In the presence of mold foci, treatment with an antiseptic composition is recommended.
Surface primer.
If necessary, level the wall completely or partially with plaster.
Subsequent priming of the plastered surface.
Full (2 - 3 layers) or partial puttying of walls.
Cleaning the putty surface.
Dedusting and subsequent priming of the surface.

Almost any pasting of the main types of wallpaper begins with priming the surface with glue. Why prime the walls before wallpapering? This is necessary in order to prepare the wall material in advance and provide additional adhesion.

Is it possible to glue wallpaper without a primer? You can, especially if you choose a good glue, but it's still better not to miss this moment, since it does not require much effort. How long after priming can wallpaper be glued? If the deadlines are not running out, then it is best to wait a few hours for the walls to dry completely.

Wallpaper to glue before or after the stretch ceiling?

What to do first: glue wallpaper or stretch stretch ceiling? First, they wallpaper the entire room, and then they mount the ceiling. Is it possible to glue ceiling plinth for wallpaper? It is much easier to stick the skirting board on the wallpaper than to fit the wallpaper to the skirting board. How to glue the ceiling plinth on the wallpaper? First, the ceiling with walls is glued and dried, and then the plinth is glued with a special glue.

Gluing technologies

How to glue wallpaper on the ceiling and in what direction (pasting ceiling wallpaper)? Start work from the window. If there are no windows in the room, then they “go” from the street wall.

Wallpaper is glued with an overlap and butt. Overlap wallpapering is practiced only for gluing joints in the corners of a room or other hard-to-reach places. And this method requires more material consumption. Butt gluing is used in all other cases. Let's consider in more detail how to glue wallpaper joint to joint.

Butt to Butt

The roll is cut into sheets of a certain length with an increase of 5 cm. Glue is applied to the spread sheet from the center to the edges. After that, the treated strip is folded in half for a more thorough impregnation. The impregnation time indicated by the manufacturer on the packaging must be the same for all subsequent strips. For a perfectly even wallpaper sticker, you can use a plumb line to draw an even line on the wall. For those who do not know which side to start gluing the wallpaper from the window or to the window, we will immediately say that the wallpaper is glued from top to bottom from the window.

The canvas glued to the wall is smoothed with a wallpaper spatula. Excess glue, as well as air bubbles, are removed with a dry cloth or sponge with strong pressure on the joints. The next canvas is glued end-to-end to the previous one, without “creeping” of the edges on top of each other.

Attention! Excess pieces at the bottom are carefully cut off with a knife only after complete drying.

Sticking in the corners

Most of the difficulties for people who decide to make repairs for the first time are caused by corners (internal and external). But with proper skill and following simple rules, these elements of the room will look aesthetically pleasing.

When part of the wall has already been glued and it has come to the outer corner, glue is applied to the wallpaper and the wall. The width of the canvas in this place should be such that the corner itself overlaps, and about 5 cm of the material passes to the adjacent wall. The sheet rises to the ceiling and is applied to the wall. The canvas wraps around the ledge. The upper part is pressed a little, and the lower part is cut with a wallpaper knife. The surface is smoothed with a brush or roller to remove air.
On an adjacent wall, in the same sequence, a sheet is glued overlapping on the first layer and smoothed with a brush.
So that there is no overlay in two layers at the corner, the top layer is cut off. A long metal ruler is applied to the edge of the corner. The layers are cut with a knife. The top layer is removed.

Tip: to avoid creases, skew at the outer or inner corner, do not glue the entire wide strip on it.

Inner corner

The inner corner is glued only with an overlap. An exception is glass wall paper, which is glued end-to-end at the corners, because even the slightest overlap is very noticeable.

Stages of gluing the inner corner:

The distance from the already glued strip to the corner is measured with the addition of 2 cm to the measurement result. The sheet is cut and bent according to this allowance, after which it is glued to the adjacent wall. The air from under the wallpaper is “expelled” with a dry cloth.
The same actions are carried out with the wall next to it. The sheet is glued overlapping on the previous canvas. It is smoothed out with a brush, but the place of the allowance in the corner is not strongly pressed.
Both layers are cut with a knife, and the excess top layer is removed.
The wallpaper in the corner is pressed hard to get rid of the air.
The bottom and top allowances are trimmed.

Attention! The denser the wallpaper material, the smaller the overlap should be.

How to glue the combined wallpaper?

How to glue combined (two types or more) wallpaper? Several can be used in one room. different types wallpaper. There can be several reasons for using combined wallpapers: hide the flaws of the wall or the room as a whole, focus on a separate area, zone the space of the room.

Tip: buy material of the same thickness, but different textures and colors.

horizontal stripes

Can wallpaper be applied horizontally? Yes, but there are a few things to keep in mind here. The optimal width of individual canvases is selected taking into account the height of the walls. For rooms with low ceilings, wallpaper up to 100 cm wide should be glued, and for rooms with high ceilings - from 150 cm to 200 cm.

The technology of gluing with horizontal stripes is quite complicated, because the accuracy of measuring the place where the strips join is required. To do this, draw a horizontal line, which should be parallel to the floor.

Gluing with horizontal stripes begins with gluing the top strip, after which the bottom strip is glued. At the joints, overlaps are left that are not smeared with glue. After the wallpaper dries, cut off the excess pieces and glue them.

vertical stripes

An excellent result can be achieved when pasting the walls with multi-colored vertical stripes. It is advisable to buy material of the same width and texture. The technology of gluing with vertical stripes is not particularly difficult. The connection of adjacent elements is carried out both overlapping and butt-to-butt. The connecting sections will not be visually noticeable, because they will lie on the border of color transitions.

Inserts

Wall decoration using wallpaper inserts is carried out on an already prepared surface. Inserts are applied to painted walls or walls with new wallpaper. Inserts can be from massive wallpaper, on a non-woven base, of various shapes and sizes. The inserts are glued simply, because their edges will be under the frame.

Wallpapering on various wall surfaces

The external attractiveness of the wallpaper and the duration of operation directly depend on the material, condition and surface treatment.

What wallpaper is better to glue on uneven walls?

How and what kind of wallpaper is better to glue on uneven walls? An excellent solution to this issue will be liquid wallpaper that can independently eliminate all flaws, making them completely invisible. Liquid wallpaper on uneven walls is important to apply as carefully as possible. And if everything is done correctly, then the result will pleasantly surprise you, eliminate the need to align the walls.

Concrete

Is it possible to glue wallpaper in winter in an apartment or house immediately on concrete walls, if so, at what temperature? It is recommended to glue wallpaper in the warm season, when the walls of the room are relatively warm. If you are not afraid of uneven walls, particles of concrete that will show through thin wallpaper, or if you decide to paste over the surface with dense material, then gluing is possible immediately on a concrete base.

The surface must first be prepared: dedusted and primed twice. Highly diluted wallpaper paste can be used as a primer. wallpapering technology concrete wall does not differ from gluing on a putty surface.

How to glue wallpaper on plywood?

How to glue wallpaper on plywood and is it possible to do this? You can glue wallpaper on plywood if you choose the right material and treat the surface well. Although paper wallpapers are the simplest and cheapest solution, due to their thin base, which is not able to mask and align plywood joints, they are not suitable for pasting wooden sheets. good options liquid wallpaper for plywood, vinyl, non-woven, textile, fiberglass wallpaper and bamboo canvases can be used for decoration.

Surface preparation consists in processing irregularities grinder and sandpaper with a coarse-grained surface. Crumbling joints can be leveled by gluing a sickle and sanding with sandpaper.

How to glue wallpaper on drywall? Do they plaster drywall?

Is it possible and how to glue vinyl paper wallpaper on drywall (plasterboard wall) without putty?

It is possible, but not necessary. But about everything and in order. Before sticking wallpaper, drywall is primed. This is done in order to protect the walls from mold and mildew, as well as to ensure good adhesion. A primer is applied from top to bottom with a roller or brush. The joints of drywall sheets are sealed with serpentine adhesive tape, which in appearance resembles a medical bandage. A starting putty is applied to the top of the seam. The recess is filled with putty flush with the rest of the surface. After drying, the excess is removed with a piece of sandpaper. When the processing of the joints is completed, proceed to the full filling of the surfaces.

Do I need to putty drywall before wallpapering? It is necessary, even if the drywall sheets are brand new. There is an explanation for this:

This way you can hide all the bolt heads.
Putty will help hide the transitions of drywall sheets.
If you stick wallpaper on a gypsum board without first preparing it, then during subsequent repairs it will be problematic to remove the wallpaper without damaging the surface of the gypsum board.

Putty is a dry material or a wet mix in a plastic bucket. There are two types of putties: starting and finishing. The starting putty is applied in 2–3 mm for preliminary leveling. Finishing putty is applied in a layer up to 1 mm and is intended for final finishing. Only after complete drying, the surfaces are polished: starting - with coarse-grained sandpaper; finishing - with fine-grained sandpaper.

A layer of primer is re-applied on the polished surface for good adhesion of the adhesive to the surface. How to glue wallpaper on a plasterboard ceiling? The technology of pasting drywall with wallpaper is no different from pasting a regular wall.

How to glue wallpaper on OSB board?

Is it possible to glue wallpaper on OSB board? Can. OSB boards after installation, they usually paint or paste over. Pasting wallpaper directly on the plate is possible, but undesirable, because the rolled material can quickly peel off. For gluing, it is recommended to adhere to the following algorithm of action:

fix the mesh-serpyanka;
apply a primer to the wall;
apply putty;
re-priming the surface;
stick wallpaper.

Tip: it is better to use a drill or a mixer to mix the putty mortar. So you get the right consistency and avoid unnecessary lumps.

Before sticking wallpaper, it is advisable to stick plain white paper on the treated surface.

How to glue wallpaper on whitewash?

Is it possible and how to paste wallpaper on whitewash (whitewashed walls)? You can glue wallpaper on a whitewashed wall, but keep in mind that the whitewash contains lime, which tends to crumble over time. If there are problem areas on the surface, then the cracked areas must be cleaned and puttied. Next, the surface is polished from lumps and other irregularities. If it is planned to paste surfaces with thick wallpaper material, the last procedure can be carried out not so carefully. The walls are primed twice. After complete drying, wallpaper glue is applied.

Is it possible to glue new wallpaper on old wallpaper?

Many are interested in holding as soon as possible repair work, so they immediately glue new wallpapers on top of the old ones. Experts still recommend a number of mandatory measures: dismantling the glued material, leveling the walls, priming, applying putty, etc. However, you should not discard the existing version of gluing over old wallpaper.

Attention! The wall to be pasted must be dry, degreased and pretreated with a primer.

To minimize all risks of peeling off new material, the following conditions should be observed:

old wallpaper should be thin and completely made of paper;
the material must adhere firmly to the surface;
the glued surface is smooth without voluminous patterns.

It is not recommended to glue new wallpapers on old vinyl or non-woven wallpapers. Due to its water-repellent properties, such material does not adhere well. And its relief structure can be seen under the new layer. Therefore, it is easier to remove the previous coating.

Wallpapering on painted walls

How to hang wallpaper on painted walls? Is it possible to glue wallpaper on water-based paint (sticking over emulsion)? Quite common questions that cause a lot of controversy. Yes, wallpapering on painted walls is possible, but you need to consider the type of paint applied. If it is a water-based paint, then there will be no difficulties. The only thing you need to check is whether it keeps well on the wall. If the wall is covered with oil paint, it will have to be removed, as the wallpaper paste can fall off immediately.

The painted wall for gluing is prepared in the following way:

all irregularities are puttied;
the surface is washed with a mild soapy solution and washed off with clean water;
the wall is primed with a light primer.

Summing up

Choosing wallpaper for a room is a rather difficult task. How to properly glue large wide meter-long vinyl-based wallpapers, how to glue non-woven wallpaper for painting on walls? After all, it is necessary to take into account not only the color, texture of rolled materials, but also the surface to which they will be glued. Moreover, each base requires careful preparation, otherwise the new wallpaper will not serve its due date.

They say that the strength of a married couple is very well tested by wallpapering the walls and ceiling. Indeed, those who do not know how to hang wallpaper correctly can end up with a scandal. After all, the canvases peel off, air remains under them, the joints shift or diverge ... And together with a stylish design, spoiled surfaces and money thrown to the wind are obtained.
But if we follow the advice of experts, we will be able to use the most spectacular and expensive wallpaper for walls without fear of damage, we will do all the work ourselves, and then we will be proud of the result. By the way, of the "valuable" advice that we inherited from "grandmother's" times, only one is true today - wallpapers really do not like drafts and humidity. Therefore, before work, I wash the floor, wait for it to dry, and then tightly close the windows and doors where a stylish transformation will take place. And do not forget that the wallpaper is pasted on prepared surfaces - strong and even, puttied and covered with a deep penetration primer.

We prepare the necessary devices

Here is a list of everything that the master will need for wallpapering:

light portable ladder, high enough and stable;
a clean plastic bucket for the adhesive solution;
a cuvette into which glue will be poured;
paint roller 25 cm wide, with medium thick fur and telescopic handle;
flat 50 mm brush;
wallpaper line;
construction knife, a set of spare blades;

Tools needed for wallpapering

sharp scissors;
tape measure, pencil for marking;
laser / water level or, in extreme cases, a plumb line (heavy nut on a thread);
wallpaper brush (if the wallpaper requires careful smoothing) or non-fading rags (in the standard case);
rubber wallpaper rollers: wide for the entire area of the cloth and narrow for the corners;
plastic ribbed roller in the form of a cone (necessary for working with heavy wallpaper);
wallpaper plastic spatula (for smooth canvases or for passing corners);
cardboard or strong film to cover the flooring;
sponge and rags to remove excess glue;
pliers, screwdriver - if necessary, dismantling switches, sockets, heating radiators.

Stage one - cutting wallpaper

So, how to glue wallpaper: the first step will always be cutting the canvases, that is, fitting them according to the pattern, marking and warehousing. If you chose wallpaper without a pattern, for which adjustment is not needed, then the required number of strips is simply cut in accordance with the height of the room. But for wallpaper with patterns and other drawings, adjustment is needed taking into account the step of the applied image (rapport).
Let's start cutting according to the following algorithm:

cut off the first strip. Its length will be equal to: ceiling height + 10 cm margin;
roll out a roll next to it. We combine it with the pattern on the first page, and make pencil marks along the edges;
in the marked place, the strip is bent and cut off. Both scissors and a table knife are suitable for this. It is important that the tool is easy to control. But ideal evenness can not be achieved, because the place of the cut will be on the technological margin, which is then removed anyway;

The first stage - cutting wallpaper

the first of the laid strips is necessarily marked (on the back, the direction of the pattern and its serial number are indicated by an arrow), after which it is folded with the reverse side outward - this will allow you to align the strip. The resulting roll is placed against the wall where it will be glued;
using the same technology, further cutting is carried out for the following canvases.
Of course, you can also mark up "the old fashioned way", that is, applying wallpaper to the wall. But it is more convenient to join the drawing on a horizontal surface.

Stage two - marking the walls

On the wall you need to draw a vertical line along which the first of the strips will be glued. Do not forget that wallpapering starts from the window - if you do not follow this simple rule, then all joints, no matter how you align them, will be visible.
A pencil is used to indicate the vertical, but with one caveat - the line is made dotted, not solid. If you apply too thick a layer of graphite, then it can "appear" through the glued coating (especially light). Width tolerance should also be provided - for example, for a 53 cm wide canvas, 54 cm recede. This will allow the wallpaper edge to be parallel to the markings, and not directly along it, which reduces the risk of deviation.

Stage three - glue: preparation and application

The success of the event called "how to stick wallpaper" is guaranteed only if the adhesive is correctly selected, prepared and applied. However, there are no complicated rules here - the glue is selected depending on the type of wallpaper and is diluted according to the manufacturer's instructions. But there are still nuances:

in one container, even if it is large, only one package of glue is bred;
water for the preparation of the composition must be clean and cold;
it is important to constantly mix the glue, pouring the dry powder into the water in a thin stream. It is best to use a construction mixer (nozzle on a drill) for this stage, and not sticks or other improvised devices.

One of the most important stages is the preparation and application of wallpaper paste.

By the time the composition has acquired the desired consistency, the prepared wallpaper strips will already be completely straightened, and it will be possible to start applying the glue. To do this, the strip is rolled out on a substrate made of cardboard or film, and the glue is poured into a cuvette. Roller, dipped in glue, go through the entire canvas, paying special attention to the edges. A uniform, but not thick layer is created over the entire surface of the wallpaper. It's good if you choose an adhesive with a colored indicator pigment - it's easier to see the empty gaps on the strip. After applying the glue, the strips are rolled up and left for impregnation - for 4 minutes, no more. You can miss 2-3 strips at the same time, no more. For some types of wallpaper, glue is applied to the walls. In this case, the place of gluing one strip is immediately passed, but with a margin of several centimeters in width. The stock will save you from having to coat the wall close to the already glued canvas, which means that the joint will not get dirty in the glue, will not warp and remain invisible.

Stage four - actual pasting

The prepared rolled strip is unfolded from above - for this you must stand on a stepladder. A pre-marked top is located and applied to the wall. Do not forget to make an overlap on the ceiling - its value is selected depending on the actual slope of the floors.
First, the upper part of the canvas is adjusted, after which you should go down to the floor and smooth the wallpaper from below (with a brush, spatula or roller - the choice of tool depends on the type of wallpaper). Smoothing is carried out from the middle to the edges, from the top to the bottom, so that all the air between the surfaces is "squeezed" out.

A folded strip of wallpaper is unfolded from above - use a stepladder for this

Then you need a rubber roller to roll the joint. It is impossible to squeeze or rub the seams so that they do not stand out after the canvases dry. If excess glue forms under them, then it is immediately erased with a sponge.
After all the canvases are glued, it remains only to cut off the overlaps. The room is protected from drafts until the wallpaper is completely dry.

Problem areas - corners and ceiling

If problems almost never arise with smooth surfaces, then the solution to the question "how to glue wallpaper in the corners?" requires a special approach. So, it is recommended to cut the canvas in the corners with a margin of 5 mm, bending it at an angle, and glue the next canvas directly on top if the wallpaper is paper. If the wallpaper is heavy, then the resulting overlap should be aligned vertically (cut off), and then continue gluing end-to-end. If you try to paste over the corner with a solid canvas, folds or horizontal deviations are inevitable.

As for the ceiling, here the pasting direction is perpendicular to the window. Here, as in the case of walls, an even strip is necessarily marked, then the canvas smeared with glue is applied and leveled, pressed, straightened and rolled out with a rubber roller. Wallpapering on the ceiling is just the case when you need an assistant, but you can deal with the walls alone.

7 important things to know

And in conclusion - a few more professional secrets:

sockets and switches (linings on them) must be removed and then installed back on top of the wallpaper;
radiators are also desirable to dismantle. This is easy to do if we are talking about modern system heating with convenient quick-release fasteners - "American". And under the old cast-iron batteries, 15 cm strips are wound up;
a light ladder is better than bulky wooden scaffolding, which can damage the "freshly created" coating;
instead of a plastic spatula, a rubber roller is used - it allows you to roll out the canvases without stretching, guaranteeing the stability of the seams;
cutting the residues along the plinth should be carried out only with a knife with replaceable blades, each time breaking off the blade so that it is perfectly sharp;
remove blotches around window slopes better the next day, dry. It does not matter if the joint will be closed with a decorative overlay;
in order not to miss air bubbles (due to fatigue or poor lighting), it is worth walking along the glued strip with your fingers, checking for rustling;
following these simple rules will allow you to enjoy high-quality results in a short time.

Do-it-yourself wallpapering is a task that anyone can handle House master. Accuracy and compliance with technical requirements are two components of success in this rather simple matter. Leveling walls requires professional skills and physical strength, but you can stick wallpaper on the wall yourself. Repairing an apartment will be cheaper if you carefully study the rules for pasting walls and strictly adhere to them.

How to paste wallpaper yourself: the secrets of success

A person who decides to carry out cosmetic repairs on his own has many questions. Is it possible to stick wallpaper alone? How to choose the right glue? How to stick wallpaper exactly? How to glue wallpaper end to end? How to quickly paste wallpaper? How to glue wide wallpaper? How to glue wallpaper in the corners of a room? These questions can be reduced to one: how to properly glue wallpaper on the walls.

Do-it-yourself wallpapering the walls, as in the photo, will become a reality if you break the task into parts and follow the recommendations.

Preparing walls for pasting

How to glue wallpaper correctly so that the result does not disappoint? A good start is half the battle: before gluing it is necessary to carefully: it must be perfectly even, white, free from litter and dust. The main rule is that it is impossible to glue wallpaper on curved walls, and it is better to invite specialists to level it. Plaster is applied to uneven areas.

If there is oil, water-based paint or old wallpaper on the walls, you will have to work hard before gluing new ones.

Is it possible? Many experts advise not to do this. To take off the old paper cover, it is enough to walk with a wet roller or a rag with soapy water. After 10-15 minutes, the paper will easily separate from the walls.

As you can see in the photo, the old coating is not always completely removed. Residues are rewetted and removed with a spatula.

If there is a waterproof film on the surface, it should be cut or scratched with a wire brush before wetting. When the surface swells, it's time to clean it off.

Removal old paint

Is it possible to glue wallpaper on sanded and primed oil paint? Professionals do not advise doing this: there is a high probability of delamination. Oil paint is removed mechanically or with the help of special chemicals. The lagging paint is removed with a spatula, and then options are possible.

Removing paint with a hammer and chisel is a laborious and lengthy process, but relatively environmentally friendly. More often, a grinder with metal brushes or a perforator is used to remove old paint. The disadvantage of this method is a large number of dust that will settle for several days. Together with the paint, a part of the concrete base is removed - as a result, the surface is dotted with irregularities, and it has to be well putty.

To remove only the paint, washes are used. Removal of paint using special chemicals is carried out in two stages: a wash is applied to the surface, and then the softened paint is cleaned off with a spatula.

It should be remembered that paint removers are very toxic, so work is carried out in a well-ventilated area, be sure to use a respirator and gloves.

To hang wallpaper on walls covered with water-based paint or whitewash, it will have to be carefully removed with water and a scraper. Hot water will make the task easier.

Pasting the walls with wallpaper can begin only after the complete removal of the previous finishing materials, correction of uneven areas, finishing puttying and grinding. The importance of these steps cannot be underestimated: proper preparation- a guarantee of excellent results.

When the walls are leveled, puttied and sanded, it remains to apply a primer that will protect the coating from moisture, prevent lag and reduce glue consumption. The primer is evenly distributed over the surface with a brush or roller about a day before wallpapering on the wall.

How to choose tools and equipment

How to glue wallpaper correctly, avoiding common mistakes? First you need to prepare the equipment.

For work you will need:

ladder;
tray;
bucket;
knife-cutter and wallpaper scissors;
narrow metal spatula;
wide spatula;
plastic spatula / wide rubber roller;
small rubber roller;
brush / roller for glue;
roulette;
pencil;
level or plumb.

The photo shows the most necessary tools: a special tray allows you to evenly distribute the glue over the roller, a plastic spatula or a wide roller is useful to press the canvas, and a narrow roller is designed for joints.

It is better to apply glue on the desktop. If it is not there, it is done on a film-covered floor.

High-quality wallpapering: what to look for

Before starting work, the question naturally arises: what to glue the wallpaper on? The adhesive composition can be selected independently, depending on the type of coating, or you can contact a sales consultant for help.

Another problem is where to apply the glue: on the wallpaper, on the wall, or on both surfaces? Pay attention to the special symbols highlighted in red in the figure: they will help you navigate.

The basic rules for wallpapering are simple

Windows and doors must be tightly closed. Why is a draft dangerous? The glue will dry too quickly, which will cause the glued sheets to peel off the walls.

A prerequisite for gluing wallpaper is de-energizing the room. It is necessary to turn off the electricity when approaching an outlet or switch: glue, like any liquid, can lead to a short circuit.

Before gluing, you need to cut the required number of strips and mark the top with a pencil on the back. It is convenient to put a mark on the edge, which will be cut off later. This will speed up the bonding process.

If the rolls are plain, the length of the strip is calculated based on the height of the ceiling with an overlap of 5 cm above and below. If there is a pattern, the length of each strip is increased by its step in order to properly join the pattern.

Work should begin by marking the wall: in order for the lines to be even, you should use a level.

Care must be taken to ensure that the adhesive does not get on outer part wallpaper: if they are light, the spots will be noticeable.

But how, so that the glue does not show through at the joints? It should not be applied much, do not be afraid that the joints will lag behind the wall a little: after drying, this deficiency can be corrected by spot application of glue from a special tube.

Beginners are often concerned about the question of how to glue the wallpaper in the corners - internal and external. Wallpapering in the corners is done at the final stage, when the main area of the room is already pasted over. It is especially difficult to glue the corners with wallpaper if there is a window opening nearby: the canvas adjacent to the window is carefully cut.

How to glue wallpaper in the corners of the room?

There are several ways.

Method 1. One glued canvas is wrapped at an angle so that a strip of about a centimeter is obtained on the adjacent wall, as in the diagram.

The second canvas is cut so that the edge fits exactly on the corner. The joints are passed with a narrow roller. If you work in this way, overlaps may be visible.

Method 2. To make even the thickest wallpaper look neat at the corners, both canvases are glued, going onto the adjacent wall by about 2 cm. Then both excess strips are removed with a cutter: for this, a wide spatula rests against the corner, which is gradually shifted until the overlaps are will be cut off completely.

The outer corners of the room are glued in a similar way. To paste over the corner protrusions, one strip is led around the corner by 1-2 cm, and the second is glued exactly along the corner. The glued corner will look neat. If the wallpaper is very dense, resort to using a cutter.

Features of pasting walls with wallpaper of different types

Modern wallpaper production makes it possible to produce products based on paper, textiles, polymer materials. Sticking wallpaper of different types has features.

paper wallpaper

How to glue paper wallpaper? It is eco-friendly and easy to operate decorative coating successfully competes with many new finishing materials. But how to glue wallpaper on a paper basis? This will help step by step instructions.

A starting line is marked on the wall, stepping back from the angle of 30-40 cm. They put a dot at the top and draw a strictly vertical line to the floor with the help of a level.
The strip smeared with glue is folded so that the glue is inside (this stage is relevant for those who glue without an assistant). If the adhesive is applied to the wall, it covers a slightly wider surface area than the roll. Under the ceiling and near the floor it is more convenient to use not a roller, but a brush.
The glued strip is pressed from above with an overlap on the ceiling of 4-5 cm (this will later allow you to cut the wallpaper in a straight line).
The side of the wallpaper is leveled and pressed with a flexible plastic spatula or a wide rubber roller strictly along the starting line.
By moving the pressure roller from the center of the strip to the edges, excess air is expelled.
Using a wide metal spatula and a paper knife, the excess part of the strip under the ceiling and at the baseboard is cut off.

A start has been made, it remains to decide whether to glue end-to-end or overlap. Previously, no one asked this question, because paper wallpapers could only be glued with an overlap. Now overlapping wallpaper is rarely glued, and there are rules here. The wallpaper must be thin, and the width of the overlap cannot be more than 15 mm.

Some types of modern paper wallpapers, for example, duplex, cannot be overlapped: because of the thickness of the paper, it looks ugly. But how to glue paper wallpaper end-to-end? According to the described scheme, only the newly glued area will play the role of the starting strip each time. Sticking wallpaper end-to-end directly depends on the quality of the preparation of the walls: if they are even, there will be no problems.

The following video shows how to properly glue the wallpaper back to back.

At the final stage, the slopes can be decorated with plastic corners.

Vinyl wallpapers

Wall covering with vinyl wallpaper has its own characteristics.

It should only be with special glue, having carefully studied the instructions: it will indicate what glue should be applied to.

The adhesive is applied to the walls in a thin layer. Before you start pasting the walls with vinyl wallpaper, the glue is allowed to dry for about 20 minutes.

How to glue wide vinyl wallpaper? To mask the joints on them, work starts from the corner closest to the window. The bottom of the strip is kept folded while the top is smoothed out.

Non-woven wallpaper

How ? Interlining is a non-woven fabric that is wear-resistant and difficult to stretch: this feature determines the technology of pasting walls with wallpaper on this basis. When choosing, interlining is also often used.

Do-it-yourself wallpaper should be glued, not forgetting the following nuances:

the base must be well puttied and have a uniform white color: due to the thinness of the coating, the walls can shine through;
the glue is carefully prepared from the powder according to the instructions and applied only to the wall;
non-woven coatings do not shrink, so they will not disperse at the joints, but the protruding glue should be immediately removed with a dry cloth, otherwise it will be noticeable after drying.

The non-woven base allows you to produce wallpapers with a width of 90-140 cm. But how to glue wide wallpapers correctly? It should be borne in mind that the walls must be very even: with a large width, even a slight curvature will affect the correctness of the joints.

How to glue wide wallpaper? To keep the canvas from moving, you need an assistant. Glue is applied, as a rule, only on the wall, and the canvases are smoothed from top to bottom. Otherwise, the technology is the same as for narrower canvases. Wallpaper should be glued correctly, avoiding glue getting on the outside. Sticking wide wallpapers is not as difficult as people who are accustomed to standard 53 cm wide rolls fear.

Armed with the knowledge of how to stick wallpaper with your own hands, and having studied many of the intricacies of the wallpapering technique, you can get to work. If the rules were followed at each stage, you can be proud of the result.